Military Engineer Services-MES has published Welcome Maintenance , Periodical Services And Repairs To Wall , Flooring , Plastering , Roof Sheet , False Ceiling , Sanitary , Joinery Etc For Triveni Complex , Sangam Complex , Corps Hq , Klp Qtrs At Rms Under Age B/R-I Of Ge 868 Ews. Submission Date for this Tender is 16-12-2020. Shed Construction Tenders in Rangapahar Nagaland. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 09-Dec-2020 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 16-12-2020 |
| Name of Work: Welcome maint, periodical services and repairs to wall, flooring, plastering, roof sheet, false celling, sanitary,joinery etc for Triveni Complex,Sangam Complex,Corps HQ KLP Qtrs at RMS. | |||||
|---|---|---|---|---|---|
| Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Demolition of cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level. | 12 | Cum | |
| 2 | 2 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings. | 132 | Sqm | |
| 3 | 3 | Dismantling asbestos cement (Corrugated or semicorrugated) sheets in roof covering. | 15 | Sqm | |
| 4 | 4 | Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified . | 150 | Sqm | |
| 5 | 5 | Dismantling boarding of any description and fixed in any position fixed with nails or screws. | 20 | Sqm | |
| 6 | 6 | Dismantling timber scantlings 40 sqcm and over in section, in unframed work any position. | 1.9 | Cum | |
| 7 | 7 | Demolition of reed lathing single or double including battens and plaster or chicken wire lathing. | 40 | Sqm | |
| 8 | 8 | Dismantling floor hearth or wall tiling including cement mortar bedding but not backing. | 676 | Sqm | |
| 9 | 9 | Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames). | 5 | Each | |
| 10 | 10 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each. | 10 | Each | |
| 11 | 11 | Taking down shutters of any description not exceeding 1 Sqm each. | 6 | Per leaf | |
| 12 | 12 | Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete. | 5 | Per leaf | |
| 13 | 13 | Refixing of shutter in the same opening not exc 1 sqm each | 4 | Per leaf | |
| 14 | 14 | Refixing of shutter in the same opening exc 1 sqm but not exc 2 sqm each | 5 | Per leaf | |
| 15 | 15 | S&F for pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified | 100 | Sqm | |
| 16 | 16 | S&F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. | 10 | Sqm | |
| 17 | 17 | S&F for 0.63mm galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 275, fixed with L-type or J-type or cranked hook bolts complete all as specified and directed. | 10 | Sqm | |
| 18 | 18 | S & F 0.80mm thick plain galvanized Mild steel sheeting, class-VIII having minimum zinc coating of 120 gm per Square metre as in ridge, valley gutter complete all as specified and directed. | 12 | Sqm | |
| 19 | 19 | S & F 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc fixed with 'L' hooks or cranked bolts complete all as specified and directed. | 10 | Sqm | |
| 20 | 20 | M&L for 6 mm thick Asbestos cement two-piece adjustable plain wing ridge complete all as specified and directed. | 5 | RM | |
| 21 | 21 | S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed aluminium grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified. | 100 | Sqm | |
| 22 | 22 | S&F for 4 mm thick veneered decorative Plywood (no of ply 05), grade-I (with BWR resin) with decorative face veneers on one face, fixed with screws to timber frame work complete all as specified and directed. | 50 | Sqm | |
| 23 | 23 | S & F for second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps. | 20 | Sqm | |
| 24 | 24 | M&L for second class hardwood as in scantlings clean sawn timber fixed complete all as specified and directed. | 1.9 | Cum | |
| 25 | 25 | M&L for rendering 15 mm thick in CM 1:4 on one side of lathing finished even and smooth without using extra cement. | 40 | Sqm | |
| 26 | 26 | M&L for rendering 12 mm thick in CM 1:6 on other side of lathing finished even and smooth without using extracement. | 35 | Sqm | |
| 27 | 27 | S & F for 0.71 mm dia wire netting of galvanised steel wire of size 12 mm mesh fixed with tinned tack of wire staple. | 40 | Sqm | |
| 28 | 28 | M&L for 15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor. | 180 | Sqm | |
| 29 | 29 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete. | 100 | Sqm | |
| 30 | 30 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick exc 0.11 Sqm but n exc 0.18 Sqm set and jointed in neat cement slurry over and including 15mm thick screed bed of CM 1:6 and pointed in white/coloured cement to match all as specified. | 150 | Sqm | |
| 31 | 31 | All as per item No 30 here-in-before but in skirting. | 10 | Sqm | |
| 32 | 32 | M&L for non - skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. | 80 | Sqm | |
| 33 | 33 | All as per item No 32 above here-in-before but in skirting. | 8 | Sqm | |
| 34 | 34 | M&L for ceramic coloured printed tiles of size 300x200mmx7 mm thick, on verticals surfaces, set and jointed in neat cement slurry and pointed in coloured. | 160 | Sqm | |
| 35 | 35 | M&L for coloured glazed ceramic tiles in vertical surface 300mmX450mmx 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed. | 68 | Sqm | |
| 36 | 36 | M&L for rendering 10 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces to received vertical tiles complete all as specified and directed. | 288 | Sqm | |
| 37 | 37 | M&L for 40 mm thk PCC 1:2:4 type B-1 using20mm graded agg as in flooring finished even and smooth with using extra cement complete all as specified and directed. | 20 | Sqm | |
| 38 | 38 | Demolition of brick work including all quoins arches pillars etc built in cement mortar. | 4.15 | Cum | |
| 39 | 39 | M&L for brick work in cement mortar (1:4) using sub class 'B' bricks straight or curved on plan exc 6.0 m mean raidus | 3 | Cum | |
| 40 | 40 | M&L for brick work with sub class 'B' bricks straight or curved on plan in any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed | 10 | Sqm | |
| 41 | 41 | Taking down cement plaster on walls built in cement mortar etc including racking out joints, hacking for key, scrubbing down with water etc. | 80 | Sqm | |
| 42 | 42 | M&L for 15mm thick cement plastering in cement mortar 1:4 brick or concrete surfaces of wall finished fair and even,complete all as specified and directed. | 60 | Sqm | |
| 43 | 43 | M&L for 15mm thick cement plastering in cement mortar 1:6 brick or concrete surfaces of wall finished fair and even with out using extra cement complete all as specified and directed. | 20 | Sqm | |
| 44 | 44 | S&F for second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete. | 0.8 | Cum | |
| 45 | 45 | S & F for 30 mm thick flush shutters , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. | 25 | Sqm | |
| 46 | 46 | S&F factory made 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, both face is covered with decorative choice sunmica lamination 0.9mm thick type I with lipping to match fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed. | 13 | Sqm | |
| 47 | 47 | S&F for second class hardwood 30 mm thick plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated. | 6 | Sqm | |
| 48 | 48 | S&F for second class hardwood glazed and skeleton door shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats. | 6 | Sqm | |
| 49 | 49 | S&F for second class hardwood glazed and skeleton window and ventilator shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats. | 15 | Sqm | |
| 50 | 50 | S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening. | 30 | Rm | |
| 51 | 51 | S&F for Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame wedded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site. | 9 | Sqm | |
| 52 | 52 | S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified | 35 | Kg | |
| 53 | 53 | S&F for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section of size 40 x 18 x 1.29mm thick including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. | 10 | Sqm | |
| 54 | 54 | S&F for anodised aluminium door shutter, aluminium section weighting 0.55 kg/m including necessary joining, cleats,glazing clips,rubbber neoprene, packing headls 2 nos in each door hinges anodised aluminium snap beading screw etc.complete all as specified. | 18 | Sqm | |
| 55 | 55 | S&F Sheet glass 4.8mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane. | 24 | Sqm | |
| 56 | 56 | S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane. | 15 | Sqm | |
| 57 | 57 | Hacking out old broken glass of any thicknesssize or description from wooden frames or metal frames fixed with wooden beads/ putty. | 10 | Sqm | |
| 58 | 58 | S&F for galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples. | 15 | Sqm | |
| 59 | 59 | S&F in repairs, galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples. | 20 | Sqm | |
| 60 | 60 | Cutting holes (superficial area Exc. half brick but not exc one brick) into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required. | 5 | Each | |
| 61 | 61 | S&F for mild steel conforming to Fe 410-0 or Fe 310-0 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; hand made sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles. | 20 | Kg | |
| 62 | 62 | M&L second class hardwood plain fillets exc 13sqcm and not exc. 25sqcm, square or rectangular in section, wrought, secured with nails or brads. | 30 | Rm | |
| 63 | 63 | M&L for preparing surface of wood and wood based matreials, new or old, of any description and girth and treaed with tar or coal tar black paint and sanding newly tarred surfaces with clean sharp sand. | 30 | Sqm | |
| 64 | 64 | M&L for preparing surfaces of small articles such as holdfast etc. of steel or iron, new or old, area not exceeding 0.1 Sqm each and treating with tar or coal tar black paint. | 1 | 100 Nos | |
| 65 | 65 | M&L for prelaminated particle board 12mm thick, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination as in pelmet boxes or in narrow widths not exceeding 15 cm each, rebated or flat edged including 6mm thick teak wood lipping allround. | 12 | Sqm | |
| 66 | 66 | M&L for prelaminated particle board 18mm thick, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination as in shelves of cup boards etc., rebated or flat edged including 6mm thick teak wood lipping on exposed edge, supported on teak wood wrought fillet of size not less than 25x25mm on three sides. | 10 | Sqm | |
| 67 | 67 | M&L Second class hard wood small fittings such as brackets of any type, shaped door and window stopers and the like, including all necessary labours, articles not exceeding 200 cu. cm each. | 7 | Each | |
| 68 | 68 | S&F Butt hinges, medium weight, cold rolled mild steel, 50mm size. | 20 | Each | |
| 69 | 69 | S&F Butt hinges, medium weight, cold rolled mild steel, 75mm size. | 45 | Each | |
| 70 | 70 | S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size. | 60 | Each | |
| 71 | 71 | S&F 300mm ordinary mild steel rat tail rod patttern springs includding roller and roller plate complete. | 10 | Each | |
| 72 | 72 | S&F Aluminium, anodised, barrel tower bolt 200mm long of extruded section and fixed complete. | 40 | Each | |
| 73 | 73 | S&F Aluminium, anodised, barrel tower bolt 150mm long of extruded section and fixed complete. | 30 | Each | |
| 74 | 74 | S&F 40 mm cupboards knobs fixed with nut screw and washer of brass polished | 10 | Each | |
| 75 | 75 | S&F for 300mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts fixed. | 20 | Each | |
| 76 | 76 | S&F Extruded aluminum alloy handles, fabricated type, anodised 100 mm size. | 10 | Each | |
| 77 | 77 | S&F in repairs Mortice lock,vertical type Brass 2 levers, size 100 mm \n | 7 | Each | |
| 78 | 78 | S&F Extruded aluminum alloy handles, fabricated type, anodised 150 mm size. | 42 | Each | |
| 79 | 79 | S&F Hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws 100mm size. | 15 | Each | |
| 80 | 80 | S&F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. fixed in repairs. | 30 | Rm | |
| 81 | 81 | M&L for french polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats. | 30 | Sqm | |
| 82 | 82 | M&L for preparation of new plastered surfaces of walls and applying two coat of dry distemper over a coat of white wash distemper all as specified. | 50 | Sqm | |
| 83 | 83 | S&F in repair for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. | 7 | Each | |
| 84 | 84 | Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed | 8 | Each | |
| 85 | 85 | S&F in repair floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor | 15 | Each | |
| 86 | 86 | Preparation of new plastered surfaces of walls and applying two coats of white wash complete all as specified and directed. | 120 | Sqm | |
| 87 | 87 | M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified. | 450 | Sqm | |
| 88 | 88 | M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. - | 110 | Sqm | |
| 89 | 89 | Material and labour for preparation of old steel surface and applying one coat of synthetic enamel paint complete all as specified and directed. | 130 | Sqm | |
| 90 | 90 | M&L for Preparation of old decorated surfaces and appplying one coat of white wash on walls, cornices etc. complete all as specified and directed. | 450 | Sqm | |
| 91 | 91 | All as per item No-90 above but two coat of white wash. | 550 | Sqm | |
| 92 | 92 | All as per item No. 90 above but on ceiling. | 150 | Sqm | |
| 93 | 93 | Complete removal of existing treatment of walls and preparation of old surfaces of wall including scrapping down, smoke soot, efflorescent salts trading oil and greasy spots etcapplying two coats of cement base paint over a coat of chalk whitening/primer complete all as specified and as directed. | 1800 | Sqm | |
| 94 | 94 | All as per item No 93 here-in-before but one coat of cement base paint on wall. | 4000 | Sqm | |
| 95 | 95 | All as per item No 93 here-in-before but one coat of exterior emulsion paint (weather coat) on wall. | 1500 | Sqm | |
| 96 | 96 | M&L for complete removal of existing treatment of wall and applying two coats of exterior emulsion paint (weather coat) over a coat of approved primer complete all as specified and directed. | 850 | Sqm | |
| 97 | 97 | M&L for Preparation of old decorated surfaces by washing, scrubbing down, and applying one coat of oil emulsion distemper on walls.all as specified and directed | 4000 | Sqm | |
| 98 | 98 | All as per item No 97 above but two coat of distemper . | 1500 | Sqm | |
| 99 | 99 | M&L for complete removal of existing treatment of wall and applying two coats of distemper oil emulsion over a coat of 3mm thick wall care putty filling complete all as specified and directed. | 1200 | Sqm | |
| 100 | 100 | M&L preparation of newly plastered surface of any description and applying two coat of plastic emulsion paint complete all as specified and as directed. | 200 | Sqm | |
| 101 | 101 | Preparation of old decorated plastered surface of any description and applying one coat of plastic emulsion paint complete all as specified and as directed. | 110 | Sqm | |
| 102 | 102 | S&F 15mm bore bib cock chromium plated fancy type, screwed down, screwed for iron pipe or for brass ferrule. | 20 | Each | |
| 103 | 103 | S&F in repairs 600mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm longfixedwith two plugs (Gutties) of 2nd class hard woodembeded in cement mortor 1:3 with MS screwscomplete all as specified. | 10 | Each | |
| 104 | 104 | S&F PVC Shelves of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105 gms) | 8 | Each | |
| 105 | 105 | S&F in repairs PVC connection 15mm size with PTMT nuts, of 450 mm length complete all as specified and directed. | 20 | Each | |
| 106 | 106 | S&F in repairs 600x450 mm size of 5.5mm thickness looking mirror, bevelled edge of selected quality glass with aluminium frame made of channel alround,mounted on 6 mm thick commercial ply or AC building board, fitted to wooden plug with CP screws complete all as specified and directed. | 10 | Each | |
| 107 | 107 | S&F in repairs for 15mm dia of pipe Angle valves,fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed . | 10 | Each | |
| 108 | 108 | S&F in repair of PVC low level flushing cistern dual flush top push,10 Ltr capacity symphonic action type white as approved, ball valve float valve and handle, flush pipe incl CP bracket | 10 | Each | |
| 109 | 109 | Supply and fixed in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed | 3 | Each | |
| 110 | 110 | Taking down AC/Salt glazed ware pipes and fittings upto 110mm. | 30 | RM | |
| 111 | 111 | S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor | 30 | RM | |
| 112 | 112 | S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor | 10 | RM | |
| 113 | 113 | S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall | 10 | RM | |
| 114 | 114 | S&F of 110mm dia PVC (SWR) bends | 10 | Each | |
| 115 | 115 | S&F 75mm PVC(SWR) bends any radius with access door. | 4 | Each | |
| 116 | 116 | S&F of 75 mm dia PVC (SWR) Vent cowl | 4 | Each | |
| 117 | 117 | S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. | 4 | Each | |
| 118 | 118 | S&F in repairs for 75mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof | 10 | Each | |
| 119 | 119 | Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing. | 55 | RM | |
| 120 | 120 | Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing. | 20 | RM | |
| 121 | 121 | Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling as directed, for 15mm bore GI tubing. | 5 | RM | |
| 122 | 122 | Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling as directed, for 20mm bore GI tubing. | 5 | RM | |
| 123 | 123 | S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore. | 50 | RM | |
| 124 | 124 | S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore. | 15 | RM | |
| 125 | 125 | M&L 75 mm thick cement concrete type C2 1:3:6 (40 mm graded aggregate) as in plinth protection, using extra cement for finishing. | 120 | Sqm | |
| 126 | 126 | S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) all as specified and directed | 4 | Each | |
| 127 | 127 | S&F in repair Flush pipe of polyethylene of low or high density or PVC, 32 mm dia, for urinal and wash basin all as specified. | 4 | Each | |
| 128 | 128 | S&F urinal sprender of PTMT any colour | 4 | Each | |
| 129 | 129 | S & F waste coupling of PTMT (half or full threaded) 32 mm dia ,complete all as specified and as directed. | 15 | Each | |
| 130 | 130 | S&F in repairs vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Sheet cover complete all as directed. | 3 | Each | |
| 131 | 131 | S&F plastic water closet seat cover, black closed pattern with flat bottom and cover and MS chromium plated or aluminium hanging device ,fixed in repair, complete all as specified and directed. | 10 | Each | |
| 132 | 132 | S&F PVC waste pipe, 32mm bore, 750mm long for basin, fixed in repair, complete all as specified and directed. | 30 | Each | |
| 133 | 133 | S&F in repairs CP wall mixer (3 in 1) complete all as specified and direcated and as approved by GE. | 2 | Each | |
| 134 | 134 | S&F in repairs CP Central hole basin mixer fancy type 15mm dia all as specified and directed. | 2 | Each | |
| 135 | 135 | S&F in repairs CP Health Faucet with 1 mtr metalic Expandable tube & hook complete all as specified and directed. | 8 | Each | |
| 136 | 136 | S&F 15mm dia pillar tap cast copper alloy chromium plated fancy type (ISI Marked) | 8 | Each | |
| 137 | 137 | M&L for chequered cement concrete tiles 300x300x25mm thick with 15mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar 1:6 set, jointed and pointed and pointed in neat cement slurry with grey cement and pigment, edges chamfered with cement over PCC 1:3:6 type C2 (40mm graded stone aggregate) 75mm thick as in sub base etc, concrete complete all as specified and directed. | 100 | Sqm |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
