| 1 | 1 | EARTH WORK | BI01010001010000000000000515BI0100001112 | | |
|---|
| 2 | 1.01 | 2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. | BI01010001010000000000000515BI0100001113 | 26.25 | sqm |
|---|
| 3 | 1.02 | 50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge | BI01010001010000000000000515BI0100001114 | 6.563 | cum |
|---|
| 4 | 1.03 | 2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. | BI01010001010000000000000515BI0100001115 | 1.321 | cum |
|---|
| 5 | 2 | CONCRETE WORK | BI01010001010000000000000515BI0100001116 | | |
|---|
| 6 | 2.01 | 4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference. | BI01010001010000000000000515BI0100001117 | 0.661 | cum |
|---|
| 7 | 2.02 | 4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference. | BI01010001010000000000000515BI0100001118 | 5.25 | cum |
|---|
| 8 | 2.03 | 13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) | BI01010001010000000000000515BI0100001119 | 30.651 | sqm |
|---|
| 9 | 2.04 | 50.6.1.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete. Min. average compressive strength as per IS shall be 40-50kg/cm2 and has to be assessed by testing at Govt. lab. ( Variation in rate due to change in size of block and level of floor as per DSR/PRICE has to be considered). | BI01010001010000000000000515BI0100001120 | 1.761 | cum |
|---|
| 10 | 2.05 | 10.16.2 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference. | BI01010001010000000000000515BI0100001121 | 844.612 | kg |
|---|
| 11 | 2.06 | 12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | BI01010001010000000000000515BI0100001122 | 103.5 | sqm |
|---|
| 12 | 2.07 | 12.51.4 : Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Barge board (Upto 300 mm). | BI01010001010000000000000515BI0100001123 | 15 | metre |
|---|
| 13 | 2.08 | 12.51.6 : Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Gutter (600 mm over all girth). | BI01010001010000000000000515BI0100001124 | 22 | metre |
|---|
| 14 | 2.09 | 13.48.3 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture. Make: Asian, Berger, Nerolac or eq. in the order of pref. | BI01010001010000000000000515BI0100001125 | 26.595 | sqm |
|---|
| 15 | 3 | Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL | BI01010001010000000000000515BI0100001126 | | |
|---|
| 16 | 4 | 2:Rate should be inclusive of installation, testing and commissioning cost for all items | BI01010001010000000000000515BI0100001127 | | |
|---|
| 17 | 5 | 3.Rate should be Exclusive of GST. | BI01010001010000000000000515BI0100001128 | | |
|---|
| 18 | 6 | 4.Work should be executed as per DSR/PWD/Irrigation Dept. specification and direction of Engineer at site. | BI01010001010000000000000515BI0100001129 | | |
|---|
