| 1 | 1 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off premises etc complete all as specified and as directed by Engr-in-Charge. | | 218 | Sqm |
|---|
| 2 | 2 | Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness below or above the ground floor etc complete all as specified and as directed by Engr-in-Charge. | | 14 | Cum |
|---|
| 3 | 3 | Demolition of brick/stone works masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and pre-cast concrete articles complete all as specified and as directed by Engr-in-Charge. | | 6 | Cum |
|---|
| 4 | 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed by Engr-in-Charge. | | 5.75 | Qtl |
|---|
| 5 | 5 | Dismantling boarding any description, fixed in any position with screws complete all as specified and as directed by Engr-in-Charge. | | 10 | Sqm |
|---|
| 6 | 6 | Dismentling of fillets, rails etc under 40 sqcm in section in framed work complete all as specified and as directed by Engr-in-Charge. | | 50 | Rm |
|---|
| 7 | 7 | Dismantling wall and ceiling board (fibre, pulp, insulations etc) or insulation board any thickness including cover fillets complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 8 | 8 | Dismantling plain or corrugated steel sheeting of any guage, thickness, including Nainital or similar pattern roof covering complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 9 | 9 | Taking down eaves, gutters and rain water pipes (any size or patterns) including all fittings, heads, shoes, bends, swan-necks etc complete all as specified and as directed by Engr-in-Charge. | | 200 | Rm |
|---|
| 10 | 10 | Taking down cement plaster on brick/stone surface of wall built in cement mortar including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by Engr-in-Charge. | | 300 | Sqm |
|---|
| 11 | 11 | Taking down chowkhat with shutter (without taking off shutter from chowkhat) area not exceeding 1.5 sqm each complete all as specified and as directed by Engr-in-Charge | | 30 | Each |
|---|
| 12 | 12 | Taking down chowkhat with shutter (without taking off shutter from chowkhat) area exceeding 1.5 sqm but n exc 4.0 sqm each complete all as specified and as directed by Engr-in-Charge | | 30 | Each |
|---|
| 13 | 13 | Taking down shutter of any description area n exc 1 sqm each complete all as specified and as directed by Engr-in-Charge. | | 20 | Per Leaf |
|---|
| 14 | 14 | Taking down shutter of any description area exc 1 sqm but n exc 2 sqm each complete all as specified and as directed by Engr-in-Charge. | | 10 | Per Leaf |
|---|
| 15 | 15 | Dismantling water tanks and removing exc 250 & n exc 500 trs capacity complete all as specified and as directed by Engr-in-Charge. | | 8 | Each |
|---|
| 16 | 16 | Dismantling water tanks and removing exc 500 and n exc 1000 trs capacity complete all as specified and as directed by Engr-in-Charge. | | 5 | Each |
|---|
| 17 | 17 | Taking up or down steel tubing and connections including for refixing or removal 15mm bore complete all as specified and as directed by Engr-in-Charge. | | 70 | Rm |
|---|
| 18 | 18 | Taking up or down steel tubing and connections including for refixing or removal 20mm bore complete all as specified and as directed by Engr-in-Charge. | | 40 | Rm |
|---|
| 19 | 19 | S&F Pre-painted galvalume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 20 | 20 | Re-securing or bolting rubber packing and adjusting alumunium door/door shutter of any description area exc 1 sqm but not exc 2 sqm each complete all as specified and as directed by Engr-in-Charge. | | 10 | Each |
|---|
| 21 | 21 | Re-securing or easing and adjusting without taking down wooden shutter of any description area not exc 1 sqm each complete all as specified and as directed by Engr-in-Charge. | | 30 | Per leaf |
|---|
| 22 | 22 | Re-securing or easing and adjusting without taking down wooden shutter of any description area exc 1 sqm but n exc 2 sqm each complete all as specified and as directed by Engr-in-Charge. | | 40 | Per leaf |
|---|
| 23 | 23 | Running welding in repairs thickness of metal to be welded exc 6mm but n exc 9mm complete all as specified and as directed by Engr-in-Charge. | | 30 | 10 Cm |
|---|
| 24 | 24 | M&L 2nd class hardwood chowkhats, plain, solid, straight, wrought, framed, rebate on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed by Engr-in-Charge. | | 0.25 | Cum |
|---|
| 25 | 25 | M&L for mild steel works as in hold fast/wind ties etc. complete all as specified and as directed by Engr-in-Charge. | | 10 | Kg |
|---|
| 26 | 26 | M&L PCC (1:2:4) type B1 using 20mm grade stone aggregate as in padding, hold fasts/filling of chowkhats or similar work complete all as specified and as directed by Engr-in-Charge. | | 0.5 | Cum |
|---|
| 27 | 27 | S&F 35mm flush shutters (ISI Marked) solid core construction, with block board core and plywood, commercial type on both sides complete all as specified and as directed by Engr-in-Charge. | | 40 | Sqm |
|---|
| 28 | 28 | S&F 35mm thick glazed and skeletion shutters 2nd class hardwood without sash bars complete all as specified and as directed by Engr-in-Charge. | | 40 | Sqm |
|---|
| 29 | 29 | S&F 30mm thick glazed and skeletion shutters 2nd class hardwood without sash bars for window,ventilators complete all as specified and as directed by Engr-in-Charge. | | 15 | Sqm |
|---|
| 30 | 30 | S & F glazed and skeleton shutters 30mm thick in 2nd class hardwood, open rebated and prepared to receive glass, gauze, etc (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc for window & ventilators complete all as specified and as directed by Engr-in-Charge. | | 15 | Sqm |
|---|
| 31 | 31 | S&F factory made steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed by Engr-in-Charge. | | 6 | Sqm |
|---|
| 32 | 32 | S&F factory made steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and as directed by Engr-in-Charge. | | 6 | Sqm |
|---|
| 33 | 33 | S&F factory made steel ventilators with top hung shutters including hinges,steel peg stay complete all as specified and as directed by Engr-in-Charge. | | 5 | Sqm |
|---|
| 34 | 34 | S&F GI mild steel wire cloth 0.56 nominal dia wire and average width aperture 1.18mm and fixed with pinned tack or galvanized staples complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 35 | 35 | S&F in repair GI mild steel wire cloth 0.56 nominal dia wire and average width aperture 1.18mm and fixed with pinned tack or galvanized staples all complete all as specified and as directed by Engr-in-Charge. | | 20 | Sqm |
|---|
| 36 | 36 | Hacking out old broken glass any thickness from metal/wooden frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 37 | 37 | S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 38 | 38 | S&F 3mm thick figured glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed by Engr-in-Charge. | | 10 | Sqm |
|---|
| 39 | 39 | S&F MS 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by Engr-in-Charge. | | 10 | Each |
|---|
| 40 | 40 | S&F in repair MS 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by Engr-in-Charge. | | 15 | Each |
|---|
| 41 | 41 | S&F mild steel sliding door bolts 300mm long complete all as specified and as directed by Engr-in-Charge. | | 30 | Each |
|---|
| 42 | 42 | S&F in repair mild steel sliding door bolts 300mm long complete all as specified and as directed by Engr-in-Charge. | | 40 | Each |
|---|
| 43 | 43 | S&F 100mm size MS butt hinges, medium weight, cold rolled complete all as specified and as directed by Engr-in-Charge. | | 90 | Nos |
|---|
| 44 | 44 | S&F in repair 100mm size MS butt hinges, medium weight cold rolled complete all as specified and as directed by Engr-in-Charge. | | 50 | Nos |
|---|
| 45 | 45 | S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-Charge. | | 30 | Each |
|---|
| 46 | 46 | S&F in repair 200mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-Charge. | | 40 | Each |
|---|
| 47 | 47 | S&F 150mm long aluminium handle cast type anodised complete all as specified and as directed by Engr-in-Charge. | | 30 | Each |
|---|
| 48 | 48 | S&F in repair 150mm long aluminium handle cast type anodised complete all as specified and as directed by Engr-in-Charge . | | 40 | Each |
|---|
| 49 | 49 | S&F 75 mm long mild steel medium weight collrolled butthinges complete all as specified and as directed by Engr-in-Charge. | | 80 | Each |
|---|
| 50 | 50 | S&F in repair 75 mm long mild steel medium weight cold rolled butt hinges complete all as specified and as directed by Engr-in-Charge. | | 50 | Each |
|---|
| 51 | 51 | S&F 125mm size aluminium handles, cast type anodised complete all as specified and as directed by Engr-in-Charge. | | 20 | Each |
|---|
| 52 | 52 | S&F in repair 125mm size aluminium handles, cast type anodised complete all as specified and as directed by Engr-in-Charge. | | 40 | Each |
|---|
| 53 | 53 | S&F 150mm long aluminium anodised barrel tower both of extruded section complete all as specified and as directed by Engr-in-Charge. | | 20 | Each |
|---|
| 54 | 54 | S & F in repair 150mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-Charge. | | 40 | Each |
|---|
| 55 | 55 | S&F small fitting shaped door and window stops n exc 200 cucm each of 2nd class hard wood complete all as specified and as directed by Engr-in-Charge. | | 30 | Each |
|---|
| 56 | 56 | S&F 50mm butt hings medium weight cold rolled and mild steel complete all as specified and as directed by Engr-in-Charge. | | 80 | Each |
|---|
| 57 | 57 | S&F in repair 50mm butt hings medium weight cold rolled and mild steel complete all as specified and as directed by Engr-in-Charge. | | 50 | Each |
|---|
| 58 | 58 | S&F 15mm dia steel tubing and fittings and connection in new or old position to walls, ceiling, floors or laid in floor etc complete all as specified and as directed | | 60 | Rm |
|---|
| 59 | 59 | S&F 20mm dia steel tubing and fittings and connection in new or old position to walls, ceiling, floors or laid in floor etc complete all as specified and as directed | | 40 | Rm |
|---|
| 60 | 60 | S&F PVC(SWR) pipe 110 mm dia single socketed in any length with rubber ring joints, fixed to wall with and including PVC stack and clamp complete all as specified and as directed by Engr-in-Charge. | | 150 | Rm |
|---|
| 61 | 61 | S&F PVC(SWR) pipe 75 mm dia single socketed in any length with rubber ring joints, fixed to wall with and including PVC stack and clamp complete all as specified and as directed by Engr-in-Charge. | | 50 | Rm |
|---|
| 62 | 62 | S&F PVC(SWR) bends any radius 110 mm dia complete all as specified and as directed by Engr-in-Charge. | | 25 | Each |
|---|
| 63 | 63 | S&F PVC(SWR) bends any radius 75 mm dia complete all as specified and as directed by Engr-in-Charge. | | 15 | Each |
|---|
| 64 | 64 | M&L for brushing neat cement slurry with 3.00 Kg of cement per sqm complete all as specified and as directed by Engr-in-Charge. | | 225 | Sqm |
|---|
| 65 | 65 | M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36sqm with and including over 15mm thick screed bed in CM (1:6) in floors, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 66 | 66 | Description all as per srl item No 65 here in before but as in skirting, dado etc with and including over 10mm thick cement plaster in CM (1:4) complete all as specified and as directed by Engr-in-Charge. | | 5 | Sqm |
|---|
| 67 | 67 | M&L for joint free non- skid colour ceramic tiles,7 to 8mm thick square/rectangular area of each tile exc 0.11 sqm but n exc 0.18sqm as in floor with and including over 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed. | | 30 | Sqm |
|---|
| 68 | 68 | Description all as per srl item No. 67 but as in skirting including 10mm thick screed bed in CM(1:4) complete all as specified and as directed by Engr-in-Charge. | | 5 | Sqm |
|---|
| 69 | 69 | M & L joint free non skid ceramic colour tiles, 7 to 8mm thick square/rectangular area of each tile exc 0.06 sqm but not exceeding 0.11sqm, as in floors with and including over 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface coloured cement to match the floor complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 70 | 70 | M&L for joint free coloured glazed ceramic colour tiles in vertical surface as in skirting / dados of size 350 mm x 250 mm x 7mm /450mm x 350mm x 7mm thick with and including over 10 mm thick cement plaster in CM (1:4); set and jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces complete all as specified and as directed by Engr-in-Charge. | | 20 | Sqm |
|---|
| 71 | 71 | M&L for machine cut kota stone slab flooring 20-25 mm thick with and including over 15mm thick screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polishing complete all as specified and as directed by Engr-in-Charge. | | 20 | Sqm |
|---|
| 72 | 72 | Description all as per srl item No.71 here-in-before but as in skirting with and including over 10mm thick cement plaster in CM (1:4) complete all as specified and as directed by Engr-in-Charge. | | 3 | Sqm |
|---|
| 73 | 73 | M&L for machine cut black granite stone slab 20 mm thick (as in cooking platform) with and including over 15mm thick CM (1:6) cement screed base laid and jointed with grey ement slurry mixed with pigment to match the shade of slab including rounding of edges, grinding and polishing complete all as specified and as directed by Engr-in-Charge. | | 20 | Sqm |
|---|
| 74 | 74 | Rounding to edges of stone slabs on edge such as in steps cooking platform and other similar situations complete all as specified and as directed by Engr-in-Charge. | | 20 | Rm |
|---|
| 75 | 75 | M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed by Engr-in-Charge. | | 3 | Cum |
|---|
| 76 | 76 | M&L for 100 mm thick cement concrete as in foundations/sub base of floor in cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregatres) complete all as specified and as directed by Engr-in-Charge. | | 80 | Sqm |
|---|
| 77 | 77 | M&L for 40mm thick cement concrete (1:2:4) type B1 (using 20mm graded aggregate) as in sub base of floor, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge. | | 80 | Sqm |
|---|
| 78 | 78 | M&L for forming contration (Dummy) joints 30 mm deep x 10 mm wide, filled with sealing compound (1 part of bitument and 3 part of sand) complete all as specified and as directed by Engr-in-Charge. | | 20 | 10 RM |
|---|
| 79 | 79 | M&L for anodised alumunium snap grid frame work for false ceiling grid of size (605mmx605mm) complete hanges from GI wire complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 80 | 80 | S&F 4mm thick texture finish type ceiling board fixed to timber/metal framed work with screw as in ceiling snap grid complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
| 81 | 81 | M&L for mild steel deformed TMT bar 10mm dia and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by Engr-in-Charge. | | 40 | Kg |
|---|
| 82 | 82 | M&L for mild steel works as in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes and similar works conforming to Fe-290, Gde-E165 etc complete all as specified and as directed by Engr-in-Charge. | | 350 | Kg |
|---|
| 83 | 83 | Excavation in post holes or similar holes each not exc 0.5 cum getting out, returning, filling and ramming earth in layers not exceeding 25 cm, watering and removing surplus soil to a distance nexc 50 mtr and making good surface complete all as specified and directed. | | 6 | Each |
|---|
| 84 | 84 | M&L for PCC (1:3:6) Type C-2, (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed by the Engineer-in-Charge | | 0.5 | Cum |
|---|
| 85 | 85 | S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed by the Engineer-in-Charge | | 85 | Kg |
|---|
| 86 | 86 | S&F plates (plain or chequered) channels, square cut or notched (odinary and couter sunk) forming holes, without any attachment of Gde Fe 410-W (Gde-E- 250) complete all as specified and directed by the Engineer-in-Charge | | 10 | Kg |
|---|
| 87 | 87 | S&F mild steel works as in hand rails, wind ties for roof, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc; flat iron fillets for securing wire etc including all necessary drilling, bolting or riveting, etc; and similar work conforming to Fe 410-0 complete all as specified and directed. | | 80 | Kg |
|---|
| 88 | 88 | M&L for applying two coats of synthetic enamel paints over a coat of red oxide primer on new steel surfaces over 10 cm width or girth including preparatinon of surfaces complete all as specified and as directed by Engr-in-Charge. | | 100 | Sqm |
|---|
| 89 | 89 | M&L for applying two coats of synthetic enamel paints over a coat of red oxide primer on new steel surfaces not exceeding 10 cm width or girth including preparatinon of surfaces complete all as specified and as directed by Engr-in-Charge. | | 10 | X RM |
|---|
| 90 | 90 | M&L for applying two coats of white wash on new wall/concrete surfaces including preparation of newly plastered surfaces all as specified and directed. | | 25 | Sqm |
|---|
| 91 | 91 | M&L for preparing the new plastered surfaces of wall and applying two coats of cement based paint over one coat of primer complete all as specified and as directed by Engr-in-Charge. | | 100 | Sqm |
|---|
| 92 | 92 | M&L for preparing newly plastered surfaces and applying two coats of distember oil emulsion white or tinted on walls after one coat of white primer with and including average 2mm thick white cement wall care putty to achieve even and smooth surface complete all as specified and as directed by Engr-in-Charge. | | 125 | Sqm |
|---|
| 93 | 93 | M & L for preparation of new surfaces and applying two coats of synthetic enamel paint over one coat primer exc 10 cm width/girth including preparation of new surface on wooden surface complete all as specified and as directed by Engr-in-Charge. | | 50 | Sqm |
|---|
| 94 | 94 | M&L for 18/19 mm thick preliminated particle board exterior grade preliminated one side with decorative choice laminated & other side balancing white laminated fixed with screw to timber frame work complete all as specified and as directed by Engr-in-Charge. | | 10 | Sqm |
|---|
| 95 | 95 | S & F 30 mm continous (piano) hinges mild steel, bright finish or electrogalvanised complete all as specified and as directed by Engr-in-Charge. | | 25 | Rm |
|---|
| 96 | 96 | S&F 75 mm hasp and staple MS stove enammeled black, including bolt to hinge plate and fixed with screw complete all as specified and as directed by Engr-in-Charge. | | 13 | Each |
|---|
| 97 | 97 | S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed by Engr-in-Charge. | | 13 | Each |
|---|
| 98 | 98 | M&L for rendering on other than fair faces of brick work 15mm thick in CM (1:6) and to be finished smooth and even with out using extra cement for internal surface complete all as specified and as directed by Engr-in-Charge. | | 125 | Sqm |
|---|
| 99 | 99 | M&L for rendering on other than fair faces of brick work 15mm thick in CM (1:4) and to be finished smooth and even with out using extra cement for external surface complete all as specified and as directed by Engr-in-Charge. | | 125 | Sqm |
|---|
| 100 | 100 | M&L for rendering 5mm thick in CM (1:3) on ceilling surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge. | | 50 | Sqm |
|---|
| 101 | 101 | S&F powder coated three track aluminium sliding window of specified aluminium section weight not less than 0.55 kg /Rm with aluminium bead, rubber bead including locking arrangement, handle, 5mm thick tinted glass and stainless steel wire mesh etc complete all as directed by Engineer-In-Charge. | | 30 | Sqm |
|---|
| 102 | 102 | M&L for powder coated alumunium chowkhat of size 101.6mmx44.5mmx1.5mm thick in section fixed to walls and alumunium frame with anodised alumunium screws complete all as specified and directed by Engr-in-Charge. | | 40 | Rm |
|---|
| 103 | 103 | S&F powder coated alumunium glazed door shutter with two panel made of vertical style of size (85x44.5)mm x1.5mm thick and Top rail size (114.30x44.5)mmx1.5mm thick bottom rail (150mmx44.5mm) x1.5mm thick and middle rail (114.3mmx44.5mm) x 1.5mm thick all alumunium section including all fittings as per door shutter such as alumunium door handles round type-2 Nos, stainless steel hinge 100mm size -4Nos, central mortice lock, alumunium tower bolts 300mm-2 Nos double leg alumunium anodised door stopper and hydraullic door closer designation No 2, universal type, cast iron body ISI marked and necessary clips rubber packing and alumunium beading to receive and including 5.5mm thick plain tined glass or 6mm thcik alumunium composite panel in top and bottom panel complete all as specified and as directed by Engr-in-Charge. | | 10 | Sqm |
|---|
| 104 | 104 | S&F pressed steel frames of size (125 x 60) mm x 1.25mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and as directed by Engr-in-Charge. | | 50 | Rm |
|---|
| 105 | 105 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed by Engr-in-Charge. | | 50 | Rm |
|---|
| 106 | 106 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame as per specification & drawing complete all as specified and as directed by Engr-in-Charge. | | 20 | Sqm |
|---|
| 107 | 107 | S&F 500 ltr capacity triple layered rotational moulded polyethylene water storage tank (cylindrical vertical closed top) hoisted and fixed in positions all as specified in SSR Part-I,with and including 20 mm dia of ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe, GI overflow pipe, GI washout pipe, antimosquito cap and fixed complete all as specified and as directed. | | 8 | Each |
|---|
| 108 | 108 | S&F 1000 ltr capacity triple layered rotational moulded polyethylene water storage tank (cylindrical vertical closed top) hoisted and fixed in positions all as specified in SSR Part-I,with and including 20 mm dia of ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe, GI overflow pipe, GI washout pipe, anti mosquito cap and fixed complete all as specified and as directed. | | 5 | Each |
|---|
| 109 | 109 | S&F 20mm dia of ball valves high pressure of PTMT with epoxy coated alumunium rod & high density plastic ball screwed for iron pipe and fixed in repair complete all as specified and as directed by Engr-in-Charge. | | 5 | Each |
|---|
| 110 | 110 | Disconnecting existing tanks setting aside for repairng, cleaning and removing all scale and dirt etc from mounths of circulating pipes etc and hoisting, reconnecting and refixing in existing position of capacity of tanks exc 500 ltrs and not exc 1000 ltrs complete all as specified and as directed by Engr-in-Charge. | | 3 | Each |
|---|
| 111 | 111 | Disconnecting exisiting tanks setting aside for repairing, cleaning and removing all scale and dirt etc from mounths of circulating pipes etc and hoisting and reconnecting and refixing in existing position, capacity of tanks exc 250 ltrs and not exc 500 ltrs complete all as specified and as directed by Engr-in-Charge. | | 2 | Each |
|---|
| 112 | 112 | Supply and fix in repair, sinks with drainage board made of stainless steel 1 mm thick sheet for, kitchen or laboratory with plugs, washers and waste pipe; cast iron cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed by Engr-in-Charge. | | 10 | Each |
|---|
| 113 | 113 | S&F in repair stainless steel kichen plate rack of size (31\"x24\"x10\") complete all as specified and as directed. | | 10 | Each |
|---|
| 114 | 114 | S&F in repair vitreous china wash basin white flat back size (550 x 400)mm including brackets, cutting for and pinning in ends of brackets or erecting stand complete all as specified and as directed by Engr-in-Charge. | | 10 | Each |
|---|
| 115 | 115 | S&F 40 mm low density polyethylene (HDPE) pipes complete all as specified and as directed by Engr-in-Charge. | | 10 | Rm |
|---|
| 116 | 116 | S&F in repair pillar tap 15mm dia cast copper alloy, wtih CP fancy type complete all as specified and as directed by Engr-in-Charge. | | 25 | Each |
|---|
| 117 | 117 | S&F in repair bib taps,15 mm bore, chromium plated, fancy type with crutch or butterfly handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by Engr-in-Charge. | | 50 | Each |
|---|
| 118 | 118 | S&F in repair 32mm waste fittings brass chromium plated for basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engr-in-Charge. | | 11 | Each |
|---|
| 119 | 119 | S&F in repair 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float and handle including brackets including flush pipe 32mm polythylene of low or high density of PVC 32mm dia for low level cistern and all needed components supplied and fixed all as specified and directed . | | 15 | Each |
|---|
| 120 | 120 | S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm including washer complete all as specified and as directed by Engr-in-Charge. | | 40 | Each |
|---|
| 121 | 121 | S & F in repair angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and as directed by Engr-in-Charge. | | 8 | Each |
|---|
| 122 | 122 | S&F in repair brass chromium plated shower rose 125mm size complete all as specified and as directed by Engr-in-Charge. | | 25 | Each |
|---|
| 123 | 123 | S & F in repair tubular towel rail, 20mm dia, D type, 60 cm long between flanges CP brass.complete all as specified and as directed by Engr-in-Charge . | | 20 | Each |
|---|
| 124 | 124 | S&F in repair 15mm dia stop valve fancy type chromium plated screwed down high pressure, with crutch or butterfly handle, screwed both hands for iron pipe or for unions complete all as specified and as directed by Engr-in-Charge. | | 10 | Each |
|---|
| 125 | 125 | S&F in repair PVC (SWR) floor trap 75mm dia plain with grating incl jointing with solvent cement complete all as specified and as directed by Engr-in-Charge. | | 10 | Each |
|---|
| 126 | 126 | M&L for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade laid over and including 25mm thick sand cushioning all as specified and as directed by Engr-in-Charge. | | 24 | Sqm |
|---|
| 127 | 127 | M&L for spreading and levelling of sand in layers n exc 25cm thick over sub base complete all as specified and as directed by Engr-in-Charge. | | 1 | Cum |
|---|
| 128 | 128 | M&L brick work using sub class B brick curved or straight on plan exc 6 mtr mean radius built in CM (1:6) complete all as specified and as directed by Engr-in-Charge. | | 3 | Cum |
|---|
| 129 | 129 | M&L brick work using sub class B brick curved or straight on plan to any radius in half brick wall builit in CM (1:4) complete all as specified and as directed by Engr-in-Charge. | | 25 | Sqm |
|---|
| 130 | 130 | M&L for precast reinforced cement concrete M-15, using 20mm graded stone aggregate set in CM (1:4) as in cover slab ( for manhole etc) including use & waste of form work for fair finished surfaces complete all as specified and as directed by Engr-in-Charge. | | 1 | Cum |
|---|
| 131 | 131 | M&L for roof treatment for approachable roof including complete removal of existing roof treatment :- (i) Rendering 10mm thick in cement mortor (1:3) mixed with liquid water proofing compound finished the surface fair and even. (ii) Applying evenly a coat of bitumen primer @ 0.30 Kg/Sqm. (iii) Applying APP modified polymeric membrane over the bitumen coat surface, weight not less than 3.2-3.5 Kg/Sqm and over lap 100mm and sealed by torch application as per manufacture insteructions. (iv) A coat of hot blown bitumen @ 1.2 Kg/ Sqm shall be applied over polymeric membrane and blinded with clean dry sand at the rate of 0.5 Kg per sqm complete all as specified and as directed by Engr-in-Charge. | | 150 | Sqm |
|---|
| 132 | 132 | M&L for 22 mm thick machine cut & polished‘ cement concrete tiles factory made conforming to IS 1237 (ISI marked) with grey cement without pigment of size (250 mm x 250 mm), laid in neat cement slurry with and including over 20 mm thick bed cement screed in CM (1:4) mixed with chemical compound PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD 200 milli - litre mixed with 50 Kg of cement or STP No 1 (LIQUID) of STP LTD in proportion 200 milli litre per 50 Kg cement, as per manufactures instructions and tiles properly laid with 3 mm wide joints filled with FEVIMATE TG of DR FIXIT of PIDILITE INDUSTRIES LTD or TILE GLUE of STP LTD as per manufactures instructions, complete all as specified & as directed. Cutting and polishing of top surfaces of tiles after fixing complete all as specified and directed by Engr- in - charge. | | 150 | Sqm |
|---|
| 133 | 133 | M&L for rendering 15 mm thick on fair faces of bricks/concrete surface in cement mortar (1:3) on wall, mixed with water proofing compound as per manufacturer's instructions finishing the surfaces even and smooth without using extra cement complete all as specified and as directed. Note:- Water proofing compound shall be measured and paid seperately. | | 20 | Sqm |
|---|
| 134 | 134 | M&L for applying two coats evenly a tack coat of hot air blown bitumen of grade 85/25 @ 1.50 Kg per sqm per coat (one coat over plaster and one coat on polythene film) including cleaning of surface over polythene film complete all as specified and as directed. | | 20 | Sqm |
|---|
| 135 | 135 | M&L for polythene film black 200 micron thick laid in floor, vertical surface etc complete all as specified and directed. | | 20 | Sqm |
|---|
| 136 | 136 | Supply only liquid water proofing compound complete all as specified and as directed by Engr-in-Charge. | | 20 | Sqm |
|---|
| 137 | 137 | Supply only liquid water proofing compound complete all as specified and as directed by Engr-in-Charge. | | 20 | Sqm |
|---|
| 138 | 138 | M&L for 40mm thick PCC (1:2:4) type B1 (using 20mm graded stone aggregate) mixed with water proofing compound as in sunken portion and making adequate slope towards spout pipe complete all as specified and as directed by Engr-in-Charge. | | 20 | Sqm |
|---|
| 139 | 139 | Supply and fixing in repair vitreous china squatting pan 'Orissa pattern' size (580x440)mm white with integral foot rests any pattern including provn of lime concrete bedding and making connection with & including PVC \"P\" Trap, etc complete all as specified and directed. | | 10 | Each |
|---|
| 140 | 140 | M&L for repair and rendering 10mm thick in CM (1:3) on chajjas, facia, roof projection, column sides, beam bottom and sides including throating after removing cracked plaster and concrete including cleaning of visible reinforcement and treating with cement slurry also necessary repair to cracked concrete if any with cement concrete (1:2:4) type B-0 (using 12.5mm graded stone aggregate) including necessary scafolding work for double/single storey bldgs complete all as specified and as directed by Engr-in-Charge. . | | 36 | Rm |
|---|
| 141 | 141 | M&L for coloured glazed chequered cement concrete tiles with grey cement and no pigment of size ( 30cm x 30cm) x 25mm thick with and including over 15mm thick screed bed in CM (1:6), set, jointed and pointed in neat cement slurry in floors complete all as specified and as directed by Engr-in-Charge. | | 30 | Sqm |
|---|
