Sales : +91-777 804 8217
| Name of Work :- Construction of Mukhya Mantri Lok Bhawan at Chilbangla (SH:- Construction of building portion including W.S & S.I , Rain water harvesting system, Septic Tank ). | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1.01 | Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out true to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable diversion pumping or bailing out and excavation shall be kept dry wherever so required by the contractor at his own cost as directed by the Engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing including all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and other incidentals to complete the work as per HPPWD specification. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases. | 204.78 | Per Cubic Metre | |
| 2 | 2.01 | Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in foundation, footing, basis of columns etcetra and mass concrete including all taxes, GST,carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. | 134.7 | Per Square Metre | |
| 3 | 3.01 | Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, pillars, posts and struts square rectangular or polygonal in plan including all taxes, GST, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. | 107.44 | Per Square Metre | |
| 4 | 4.01 | Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights from floor including all taxes, GST, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. | 145.88 | Per Square Metre | |
| 5 | 5.01 | Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetra upto any thickness including all taxes, GST,carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. | 123.63 | Per Square Metre | |
| 6 | 6.01 | Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing including all taxes, GST,carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. | 12.92 | Per Square Metre | |
| 7 | 7.01 | Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling upto any heights and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls upto all width and heights including all taxes,GST, including carriage of material and other incidentals within all leads and lifts and as per the direction of the Engineer-in-charge. | 62.35 | Per Running metre | |
| 8 | 8.01 | Providing and laying mechanically mixed and vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred thirty kilograme per cubic metre) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundations, footings bases of columns and the like and mass concrete including all taxes,GST, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. | 41.88 | Per Cubic Metre | |
| 9 | 9.01 | Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 320 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in columns, pillars, posts and struts upto floor all levels as per the directions of the Engineer-in-charge including all taxes, GST,carriage of material within all leads and lifts and other incidentals. | 11.31 | Per Cubic Metre | |
| 10 | 10.01 | Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 320 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landing, shelves and their support, balconies, beams, girders, bressumers and cantilever upto floor all levels as per the directions of the Engineer-in-charge including all taxes, GST, carriage of material within all leads and lifts and other incidentals. | 45.33 | Per Cubic Metre | |
| 11 | 11.01 | Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 320 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in stair cases and connected work upto floor all levels as per the directions of the Engineer-in-charge including all taxes, GST, carriage of material within all leads and lifts and other incidentals. | 1.6 | Per Cubic Metre | |
| 12 | 12.01 | Providing and laying mechanically mixed and vibrated reinforced cement concrete M-20 (M-twenty) design mix to obtain the minimum compressive strength of 20 N/mm square (twenty newton per square millimetre) with cement contents not less than 320 Kg/ Cubic metre and curing complete including form work in moulding as in cornices, window sills etc. upto floor all level as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. | 1.69 | Per Cubic Metre | |
| 13 | 13.01 | Providing and laying mechanically mixed and vibrated plain cement concrete M 20 with cement contents not less than 320 KG/cum (Three hundred twenty kilogram oer cubic metre) curing complete excluding the cost of form work in foudation and plinth within all leads and lifts as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 1.71 | Per Cubic Metre | |
| 14 | 14.01 | Providing and laying cement concrete M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 320 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) reinforced concrete chajjas upto any thickness and upto floor all level including finishing the exposed surfaces with cement mortor 1:3 ( One cement isto three sand) to give a smooth and even surface centering /form work and curing complet excluding the cost of reinforcement within all leads and lifts and as per the directionof the Engineer-in-charge and other incidentals. | 1.01 | Per Cubic Metre | |
| 15 | 15.01 | Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone agreegate 40 mm (forty millimetre) nominal size) curing complete excluding the cost of form work in foudation and plinth including all taxes, GST, carriage of material, within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. | 12 | Per Cubic Metre | |
| 16 | 16.01 | Providing and laying mechanically mixed and vibrated cement concrete 1:6:12 (one cement isto six sand isto twelve graded crushed stone aggregate 40 mm (forty millimetre) nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth including all taxes,GST, carriage of material, within all leads and lifts within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. | 11.08 | Per Cubic Metre | |
| 17 | 17.01 | Providing tor steel reinforcement for reinforced cement concrete work including straightening, bending, binding and placing in position complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 12278.7 | Per Kilogram | |
| 18 | 18.01 | Random rubble masonry/polygonal rubble masonry (uncoursed / brought to courses ) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto twelve graded stone agreegate 20mm (twenty millimetre) nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand) as per the directions of the Engineer-in-charge including all taxes and carriage of material within all leads and lifts and other incidentals. | 11.35 | Per Cubic Metre | |
| 19 | 19.01 | Precast concrete block masonry (including quion blocks, jamb blocks, clousers etcetera) with solid concrete blocks of approved size made of cement concrete 1:3:6 (one cement isto three sand isto six graded stone agreegate 40mm (forty millimetre) and down gauge) in foundation and plinth with cement mortar 1:6 (one cement isto six sand) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 10.81 | Per Cubic Metre | |
| 20 | 20.01 | Stone filling under floor/ behind retaining wall etctra complete including all taxes and carriage of material, as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 18.56 | Per Cubic Metre | |
| 21 | 21.01 | Second class brick work using common brunt clay building bricks of approved quality in super structure above plinth level upto floor all levels in cement mortar 1:6 (one cement isto six sand) curing complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 19.29 | Per Cubic Metre | |
| 22 | 22.01 | Half brick masonry using second class common brunt building brick with hoop iron of approved quality in super structure above plinth level upto floor all levels in cement mortar 1:4 (one cement isto four sand) curing complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 85.02 | Per Square metre | |
| 23 | 23.01 | Squared rubble masonry coursed with hard stones of approved quality in foundation and plinth including raking out joints in cement mortar 1:5 (one cement is to five sand) curing complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 7.13 | Per Cubic Metre | |
| 24 | 24.01 | Providing & fixing 40 mm ( forty millimetre) thick second class deodar wood shutter for door with infill pannel of 12 mm thick ( twelve millimetre) phenol bonded pre-laminated board (both side) particle board ISI marked No. IS-12823 including ( below middle rail) or its eqivalent pannel above middle rail sahll be of 5 mm ( five milimetre) thick glass with black enamle iron butt hinges with necessary screws complete or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. | 6.49 | Per Square metre | |
| 25 | 25.01 | Providing and fixing 35 mm (thirty five millimetre) thick flush door shutters interior grade, commercial type, core of block-board of both side commercial decorative phenol bonded cantuary / Alpro / Duro Ply / Green ply ISI mark No. 2202 construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. | 10.33 | Per Square Metre | |
| 26 | 26.01 | Providing and fixing to existing door frames, 30mm (thirty millimetre) thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 (ninteen) gauge thickness and size of 19mm x19mm (ninteen into ninteen millimetre) for styles and 15mmx15mm(fifteen into fifteen millimetre) for top and bottom rails, (code No. 9.128 of RAJSHRI )M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC \"C\" channel of size 30mm thickness, 70mm (seventy millimetre) width out of which 50mm( fifty millimetre) shall be flat and 20mm (twenty millimetre) shall be tappred in 45 (forty five millimetre) degree angle on either side forming style and 5mm(five millimetre) thick, 95mm (ninety five millimetre) wide, PVC sheet out of which 75mm (seventy five millimetre) shall be flat and 20mm (twenty millimetre) shall be tapered in 45 (forty five ) degree on the inner side to form top and bottom rail and 115mm (one hundred fifteen millimetre) wide PVC sheet out of which 75mm (seventy five millimetre) shall be flat and 20mm (twenty millimetre) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (ten millimetre) thick, 20mm (twenty millimetre) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm (five millimetre) thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style and rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm (one hundred into fifty into one point nine zero millimetre) size with necessary screws etc complete or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 5.45 | Per Square Metre | |
| 27 | 27.01 | Providing and fixing 19mm (ninteen millimetre) thick water proof commercial board in shelves / box for cup boards with butt joints and fixing with nails and screws etcetra complete the shelf shall be finished with 6/12mm (six / twelve millimetre) thick hard wood edging as per the direction of the engineer-in-charge, and drawing & design complete including all taxes and carriage of material within all leads and lifts and other incidentals. | 12.42 | Per Square Metre | |
| 28 | 28.01 | Providing and fixing 19mm (nineteen millimetre) thick commercial board water proof shutters of century / kit ply/ Duro ply/ Mariano ISI marked shutter for cup boards including fixing with nickel plated piano hinges with screws etcetera complete the shutter from all sides shall be finished with 2.5mm (two point five millimetre) thcik hard wood edging including all taxes and carriage of materials within all leads, liftsas per specification as per the direction of the Engineer-in-charge and other incidentals. | 5.5 | Per Square Metre | |
| 29 | 29.01 | Providing and fixing 6mm (six millimetre) thick ply of century / kit ply/ Duro ply/ Mariano ISI marked wood linning with but jointing and nails ( frame work and cover filets to be measured and paid for separately) including all taxes and carriage of materials within all leads, liftsas per specification as per the direction of the Engineer-in-charge and other incidentals. | 5.5 | Per Square Metre | |
| 30 | 30.01 | Providing and fixing 1mm (one millimetre) thick coloured or plain limination sheet ( Sunmica) on board / Ply board sheets with approved adhesive and nails etc. complete including all taxes and carriage of materials within all leads, lifts as per specification as per the direction of the Engineer-in-charge and other incidentals. | 5.5 | Per Square Metre | |
| 31 | 31.01 | Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetera complete 200 X 10 mm (two hundred into ten millimetre) including all taxes and carriage of materials within all leads, lifts as per specification and as per the direction of the Engineer-in-charge and other incidentals. | 8 | Each | |
| 32 | 32.01 | Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etcetra complete 250x16 mm (two hundred fifty into sixteen millimetre) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 7 | Each | |
| 33 | 33.01 | Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etcetera complete 125 mm (one hundred twenty five millimetre) including all taxes and carriage of materials within all leads, lifts as per specification and as per the direction of the Engineer-in-charge and other incidentals. | 20 | Each | |
| 34 | 34.01 | Prokviding and fixing 65x35mm ( sixty five into thirty five) special quality bright finished brass cup board locks or wardrobe locks with six levers including necessary screws etc complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 6 | Each | |
| 35 | 35.01 | Providing and fixing bright finished brass ball catcher 10 mm ( ten millimetre) dia including necessary screws etc. complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 15 | Each | |
| 36 | 36.01 | Providing and fixing M.S. plain grills 10x10mm (ten into ten millimetre) square or round bars in combination of 20x4mm (twenty into four millimetre) M.S. flat as per detail of required pattern in frames of windows etc.with M.S.Flats, square or round bars with round headed bolts and nuts or by screws as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 798.12 | Per Kilogram | |
| 37 | 37.01 | Providing and fixing bison board ceiling 595x595mm( five hundreds ninety five into five hundred ninety five millimetre) cascade in powder coated G.I. frame work complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 7.92 | Per Square metre | |
| 38 | 38.01 | Providing and fixing Uni-stone 12mm (twelve millimetre) cladding on RCC surface side as on faces of Arch masonary walls etcetera on 12mm (twelve millimetre) thick cement plaster 1:3 (one cement isto three sand) and jointed with cement slurry including scaffolding etcetera complete including as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 67.18 | Per Square metre | |
| 39 | 39.01 | Providing and laying 10mm (ten millimetre) thick water proof stain and impact resistant heavy duty, double charged vetrified tiles orient Bell /Nitco of equivalent shade 600x600x10mm (six hundred into six hundred into ten millimetre) size manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) with Ist quality granite border jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including all taxes and carriage of materials within all leads, lifts as per specification as per the direction of the Engineer-in-charge and other incidentals. | 100.13 | Per Square Metre | |
| 40 | 40.01 | Providing and laying 1st class matt finished spartic ceramic tiles 10 mm ( ten millimetre) thick 300mm X 300mm (three hundred millimetre into three hundred millimetre) size in flooring, laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 ( one cement isto three sand) finished with flush pointing in white cement as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 7.92 | Per Square Metre | |
| 41 | 41.01 | Providing and laying 25mm (twenty five millimetre) thick kota stone flooring of 55'' X 55'' size (twenty two inches into twenty two inches) size laid over 20mm (twenty millimetre) thick base of cement mortar 1:4 (one cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of kota stone including rubbing and polishisng to granolithic finish and with 7.5cm (seven point five centimetre) Jaiselmer Yellow / Baroda green marble strip as per approved pattern or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 24.54 | Per Square Metre | |
| 42 | 42.01 | Providing and fixing 300mm X 300mm (three hundred millimetre into three hundred millimetre) anti skid tiles in labrador design Rain bow series of NTC design laid over bed of cement mortar 1:4 (one cement isto four sand) including all taxes, carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-chief and other incidentals. | 4.12 | Per Square Metre | |
| 43 | 43.01 | Providing and laying 25mm (twenty five millimetre) thick kota stone single slab with round nosing in flooring, treads of steps 20mm (twenty millimetre) (average) thick base of cement mortar 1:4 (one cement isto four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of kota stone including rubbing and polishisng complete as per approved pattern including carriage of material within all leads and lifts and as per the direction of the engineer-in-chief and other incidentals. | 17.18 | Per Square Metre | |
| 44 | 44.01 | Providing and laying granite stone in skirting or riser of steps 20mm (twenty millimetre) (average)thickness base of cement mortar 1:3( one cement isto three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm (twenty lillimetre) thick including all taxes, carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-charge and other incidentals. | 6.18 | Per Square Metre | |
| 45 | 45.01 | Providing & laying coloured glazed tiles of KAJARIA/ SOMANY/ JOHNSON/ SWASTIK or equivalent make 6mm (six millimetre) thick 30 x 45 cm ( thirty into forty five centimetre) in skirting and dado on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) finished with flush pointing in white cement upto floor all level as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 52.64 | Per Square Metre | |
| 46 | 46.01 | Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a primming coat of red lead paint in trusses and trusses purlins in building as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 4.6 | Per/ quintel | |
| 47 | 47.01 | Providing and fixing angle iron door, window, clerestory window frame manufactured from steel iron section of 40x40x6mm (forty millimetre into forty millimetre into six millimetre) with M.S. flat in combination of 50x4mm ( fifty into four millimetre) including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angles 50x25mm (fifty millimetre into twenty five millimetre) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel but hinges 2.5mm (two point five millimetre) thick with provision for locking arrangement and shock obsorber as specified and applying a coat of approved steel primer after preteatment of the surface as per specification as dirceted by Engineer-in-charge within all leads and lifts and as per the direction of the Engineer-in-charge including all taxes, cariage of material and other incidentals. | 32.2 | Per Running Metre | |
| 48 | 48.01 | Providing and fixing factory made PVC door frame single rebate of any clours of size 50x47mm (fifty into forty seven millimetre) with a wall thickness of 5mm (five millimetre) made out of extruded 5mm(five millimetre) rigid PVC foam sheet heat bend and mitred at corners and jointed with 2 Nos. (two numbers) of 150mm (one hundred fifty millimetre) long brackets of 15mmx15mm (fifteen into fifteen millimetre) M.S. square tube, the vertical door profiles to be reinforced with 19mmx19mm (ninteen into ninteen millimetre) M.S. square tube of 19 (ninteen) gauge of RAJSHRI ( code No. 16.24) EPDM rubber gasket weather seal to be provided throughout the frame including fixing of door frame to wall with M.S. screws 100 (one hundred) long with wooden or rawl plugs emedded in masonry complete or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 14.4 | Per Running Metre | |
| 49 | 49.01 | Providing and fixing steel door, windows, ventilaters and clerestory windows frame manufactured from M.S. channal 75x40x4mm (Seventy five into fortyinto four millimetre), size M.S. angle 25x20x3mm (twenty five into twenty into three millimetre) M.S. T-Section 25x25x3mm (twenty five into twenty five into three millimetre) size vertically welded with M.S. flat 75 X 4mm (Seventy five into four millimetre) for central frames with split to end tail to each jambs including joints and miterd and welded with 16 X 3.15mm (Sixteen into three point five millimetre) lugs 10cm (ten centimetre) long embedded in cement concrete block 15cm X 10cm X 10cm (Fifteen centimetre into ten centimetre into ten centimetre) size of 1:3:6 (one cement isto three sand isto six graded crushed stone aggregate twenty millimetre nominal size) with provision for locking arragnement and shock observor fixed with by mechanical means lugs and curing complete including applying a coat of approved steel primer after pretreatment of the surface as specified including all taxes, carriage of materialwithin all leads and lifts as per specification as per the direction of Engineer-in-Charge and other incidentals. | 1130.55 | Per Kilogram | |
| 50 | 50.01 | Providing and fixing fixed steel glazed windows and ventilators of standerd rolled steel sections,joints mitred and welded with 16x3.15 mm ( sixteen into three point fifteen) lugs 10 cm. (ten centimetre) long embedded in cement concrete blocks 15 cmx10cmx10cm size ( fifteen into ten into ten centimetre) of 1:3:6(one cement isto three sand isto six graded stone aggregate 20mm (twenty millimetre) nominal size)or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts in fixed steel windows as required and iron fittings,including providing and fixing 5mm (five millimetre) thick modi guard glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint as per specification incluiding all taxes and as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. | 23.49 | Per Square Metre | |
| 51 | 51.01 | Providing and fixing top hung steel glazed ,windows and ventilators of standerd rolled steel sections,joints mitred and welded with 16x3.15 mm ( sixteen into three point fifteen) lugs 10 cm. (ten centimetre) long embedded in cement concrete blocks 15 cmx10cmx10cm size ( fifteen into ten into ten centimetre) of 1:3:6(one cement isto three sand isto six graded stone aggregate 20mm (twenty millimetre) nominal size)or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts side hung windows as required and iron fittings,including providing and fixing 5mm (five millimetre) thick modi guard glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint as per specification incluiding all taxes and as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. | 5.76 | Per Square Metre | |
| 52 | 52.01 | Providing and fixing side hung steel glazed windows and ventilators of standerd rolled steel sections,joints mitred and welded with 16x3.15 mm ( sixteen into three point fifteen) lugs 10 cm. (ten centimetre) long embedded in cement concrete blocks 15 cmx10cmx10cm size ( fifteen into ten into ten centimetre) of 1:3:6(one cement isto three sand isto six graded stone aggregate 20mm (twenty millimetre) nominal size)or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts in top hung ventilators as required and iron fittings,including providing and fixing 5mm (five millimetre) thick modi guard glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint as per specification incluiding all taxes and as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. | 17.35 | Per Square Metre | |
| 53 | 53.01 | Providing 40 mm ( forty millimetre) dia M.S. hollow pipe hand railing with slip resistant with round ends at two level at 75 cm ( seventy five centimetre) and 90 cm ( ninety centimetre) height with 50 mm ( fifty millimetre) dia pipe fixed to vertical members @ 60 cm ( sicty centimetre) center to center complete as per Arch. Drg. No. 33 Job 7704 or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. | 8.1 | Per Running metre | |
| 54 | 54.01 | Providing and fixing railing with baluster 20x20 mm ( twenty into twenty millimetre) solid squars bars connected with 20 x20 mm ( twenty into twenty millimetre) square bars fixed with top M.S. flat 40 x5 mm ( forty into five millimetre) and pipe of size 62 x75 mm ( sixty two into seventy five millimetre) hollow pipe hand rail as per Arch.Drg. no. 17 Job 6470 or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. | 6.7 | Per Running metre | |
| 55 | 55.01 | Providing and fixing steel windows side hung wire gauge of standard rolled steel sections joints mitred and welded with mechanical means to relevent ISI standard specification frames and in M.S. Tee section 25X15X3mm (twenty five millimetre into fifteen millimetre into three millimetre) including glazing clips or pins, , M.S. wire mesh 4 designation 85 (eighty five) SWG and M.S. fitting as required including providing and fixing of projecting, hinges, tower bolts, handles, hooks and eyes, presty, locking arrangment spring catch etcetra and providing and fixing wire mesh fly proof including fixing with special metal sesh putty of approved make complete including applying a priming coat of red lead paint within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. | 22.49 | Per Square metre | |
| 56 | 56.01 | Providing and fixing M.S. B.P. sheet 1.66mm (one point six six millimetre) any thickness in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per specification including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in-chief and other incidentals. | 2.56 | Per Square Metre | |
| 57 | 57.01 | Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheets in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron (twenty micron) over 5 microns (five micron) primer coating and back coat of polyster of 5 microns (five micron) over 5 microns (five micron) primer coating of TATA / SAIL/ RELIANCE/ ZINDAL STEEL including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet washers complete with all accesories as required including all taxes, carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-chief and other incidentals. | 30.72 | Per Square Metre | |
| 58 | 58.01 | Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm (four point five kilogram per square metre) including filling the joints with approved adhesive complete or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. | 17.6 | Per Running metre | |
| 59 | 59.01 | Providing and fixing on wall faces PVC (D-plast)finolex 110mm (one hundred millimetre) dia PVC plain bend for rain water pipes including filling the joints with approved adhesive complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 8 | Each | |
| 60 | 60.01 | Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter with Readymixed paint brushing wood primer pink as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 35.17 | Per Square metre | |
| 61 | 61.01 | Painting two or more coats (excluding priming coat ) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stoping with enamel paint other than whiteas directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 35.17 | Per Square metre | |
| 62 | 62.01 | Painting two or more coat (excluding priming coat) on new steel and other metal surfaces under coat with ready mixed paint brushing to give an even shade including cleaning the surface all dirt, dust and other foreign matter with enamled paint other than white including all taxes, carriage of materials, within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. | 49.26 | Per Square metre | |
| 63 | 63.01 | 15mm (Fifteen millimetre) cement plaster in single coat on rough side of brick / concrete / stone masonry for interior plastering upto floor all levels including arises, internal rounded angle, chamfer and / or rounded angle not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement isto six sand) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 323.93 | Per Square Metre | |
| 64 | 64.01 | 15mm (fifteen millimetre) cement plaster in single coat on fair side of brick / concrete / stone masonry for interior plastering upto floor all levels including arises, internal rounded angle, chamfer and / or rounded angle not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement isto six sand) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 137.92 | Per Square metre | |
| 65 | 65.01 | 15mm (fifteen millimetre) thick cement plaster in single coat on fair side of brick / concrete / stone walls for interior plastering upto floor all levels including arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth with cement mortar 1:3 (one cement isto three sand)as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals. | 8.26 | Per Square metre | |
| 66 | 66.01 | 6mm (six millimetre) thick cement plaster to ceiling in cement mortar 1:3 ( one cement isto three sand) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 123.74 | Per Square metre | |
| 67 | 67.01 | Applying Birla white wall care putty over plastered surface after thoroughly brushing the surface free from mortar drops, dust loose materials and other foreign matter sand papered smooth to give final matter finish to the surface complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 585.59 | Per Square metre | |
| 68 | 68.01 | Finishing walls with Apex weather proof exterior grade emulsion of Asian paint or exterior emulsion of NAROLAC SURKSHA as per approved shade on undecorated wall surface (two or more coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 137.92 | Per Square metre | |
| 69 | 69.01 | Wall painting (two or more coats) with acrylic emulsion paint of Asian / Narolac approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 447.67 | Per Square metre | |
| 70 | 70.01 | Providing plinth protection with inter locking paver 60 mm (sixty millimetre) thick of M-50 (M-Fifty ) Grade of approved make with 23 cm ( twenty three centimetre half rounded stone ware pipe for drainage purpose laid over including cement concrete 1:5:10 (one cement is to Five sand is to ten graded stone aggregate) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 34.76 | Per Square metre | |
| 71 | 71.01 | Providing and laying Dr. fixit torchshield ( P-3160-3mm) shall be usded for water proofing treatment or fixit torchshield membrance made from high grade bitumen and selector ploymer the APP/SBS modified bitument in three coated to non woven hoister reinforcement to give high teir and procture resistance the application should be done as per specification approved drawings, design as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 16.8 | Per Square metre | |
| 72 | 72.01 | Providing and fixing C.P. brass angle valve 15mm (fifteen millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 4 | Each | |
| 73 | 73.01 | Providing and fixing PVC connection with brass union 45cm. (forty five centimetre) Long and 15mm (fifteen millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 4 | Each | |
| 74 | 74.01 | Providing and fixing to wall, ceiling and floor galvanised mild steel tubes (medium grade) tube fittings and clamps including making good the wall, ceiling and floor 20mm ( twenty millimetre) nominal bore as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 35 | Per running metre | |
| 75 | 75.01 | Providing and laying in trenches galvanised mild steel tubes (medium grade) tube fittings (Earth work in trenches to be measured and paid for separately) 20 mm (twenty millimetre) nominal bore as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 18 | Per running metre | |
| 76 | 76.01 | Providing & Fixing to wall ceiling and floor galvanized CPVC of lubrizol flow -15 mm dia or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 39 | Per running metre | |
| 77 | 77.01 | Making connection of galvanised steel distribution branch with galvanised mild steel main 20 mm to 40 mm (twenty millimetre to forty millimetre) nominal bore by providing and fixing tee including cutting and threading the pipes complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 1 | Each | |
| 78 | 78.01 | Providing and placing in position 1000 (one thousand) litres net capacity PVC water storage tank of ISI 12701 marked G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangment including hoisting upto all heights above ground level as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 1 | Each | |
| 79 | 79.01 | Providing and fixing PVC 110x90mm (one hundred ten into ninety millimetre) dia floor trap ISI Marked of self cleaning design including fixing with approved adhsive, cost of cutting making the walls and floors etc. complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 3 | Each | |
| 80 | 80.01 | Providing and fixing high pressure PVC spigot and socket of Phenolex/Relimirel /Rected supreme make , waste and ventilating pipes ISI marked having 4 to 4.6 mm ( four to four point six millimetre) thickness including fixing with approved adhesive 150 mm (one hundred fifty millimetre) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 7 | Per running metre | |
| 81 | 81.01 | Providing and fixing high pressure PVC spigot and socket of supreme make , waste and ventilating pipes ISI marked having 4 to 4.6 mm ( four to four point six millimetre) thickness including fixing with approved adhesive 110 mm (one hundred ten millimetre) diaas directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 7 | Per running metre | |
| 82 | 82.01 | Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive 150 mm (one hundred fifty millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 3 | Each | |
| 83 | 83.01 | Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive 110 mm (one hundred ten millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 2 | Each | |
| 84 | 84.01 | Providing and laying PVC plain bend of ISI marked including fixing with approved adhesive etc. complete 150 mm (one hundred fifty millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 3 | Each | |
| 85 | 85.01 | Providing and laying PVC plain bend of ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 4 | Each | |
| 86 | 86.01 | Providing and fixing vitreous China wash down water closet (European type W.C. pan) with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement isto one sand). Seat and cover to be measured and paid for separately as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 1 | Each | |
| 87 | 87.01 | Providing/Fixing EWC matrix fixed with jet pressure of Hindware/Cera jaquare fixed to pre cistern with Jet pressure of star white /snow white including necessary fitting complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 1 | Each | |
| 88 | 88.01 | Providing and fixing plastic seat (Solid) type and cover for wash down water closet with C.P. Brass hinges and rubber buffers as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. | 1 | Each | |
| 89 | 89.01 | Providing and fixing 5.00 ltr. capacity PTMT coloured/ white automatic flushing cistern of cera/hindware with a pair of PVC / C.I. brakcets complete with fitting including P.V.C. syphonic apparatus, mosquito proof lid PVC union and coupling for connection with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. | 1 | Each | |
| 90 | 90.01 | Providing/Fixing wash basin for divyang of matrix of Hindware/Cera jaquare including necessary fitting complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 2 | Each | |
| 91 | 91.01 | Providing and fixing C.P. brass waste continental series of Jaquar / contessa series of hindware/ ocean series of Cera of 32mm (thirty two millimetre) dia size for sink or wash basin.as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals. | 3 | Each | |
| 92 | 92.01 | Providing/Fixing SST grab bar 40mm dia at 78 cm heigth with MS plate at the position of seal and wash basin in toilet for disabled portion as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 1 | Each | |
| 93 | 93.01 | Providing and fixing 600mm X 450 mm (six hundred millimetre into four hundred fifty millimetre) bevelled edge mirror of superior glass mounted on 6mm (six millimetre)thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 2 | Each | |
| 94 | 94.01 | Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for wash basin complete recessed at the back for the reception of pipes and fittings as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 2 | Each | |
| 95 | 95.01 | Providing and fixing 600mm X 20mm (six hundred millimetre into twenty millimetre) C.P. brass towel rail of continental series of Jaquar / contessa series of hindware/ ocean series of Cera complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 2 | Each | |
| 96 | 96.01 | Providing and fixing charomium plated brass soap dishof continental series of Jaquar / contessa of hindware/ ocean series of Cera with C.P. brass brackets fixed to wooden cleats with C.P. brass screws as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 2 | Each | |
| 97 | 97.01 | Providing and fixing C.P. brass bib tap of continental series of Jaquar / contessa of series of hindware/ ocean series of Cera with 15 mm (fifteen millimetre) dia with capaston head as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 3 | Each | |
| 98 | 98.01 | Providing and fixing C.P. brass pillar tap with capstan head 15mm (fifteen millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government . | 2 | Each | |
| 99 | 99.01 | Providing and fixing 15 mm dia C.P. stop cocks as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. | 2 | Each | |
| 100 | 100.01 | Providing and fixing CP Brass Zet with necessary fitting complete as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. | 2 | Each | |
| 101 | 101.01 | Providing and fixing 610x510 mm with bowl depth 200 mm stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. | 1 | Each |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
