| 1 | 1 | Dismantling plain or corrugated steel sheeting any guage/ thickness incl Nainital pattern or similar pattren roof covering in patches complete all as specified & directed. | | 125 | Sqm |
|---|
| 2 | 2 | Dismantling of Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings incl ridge etc. complete all as specified and directed. | | 150 | Sqm |
|---|
| 3 | 3 | Demolition of brick work or stone boulder masonry built in cement mortar complete all as specified and as directed. \nNote:- The demolished material should be disposed off out side the MOD land. The contractor shall quote his rates considering this factor | | 7.4 | Cum |
|---|
| 4 | 4 | Taking down cement plaster of any description on brick / concrete surfaces etc including raking out joints hacking for key, scrubbing down with water etc complete all as specified. \nNote:- The demolished material should be disposed off out side the MOD land. The contractor shall quote his rates considering this factor. | | 250 | Sqm |
|---|
| 5 | 5 | Dismantlling Structural mild steel work of any description not otherwise provided for complete all as specified and directed. | | 2 | Qtl |
|---|
| 6 | 6 | Demolition of cement concrete (un- reinforced) in ground floor and paving n. exc 15 cm thick bleow or above ground level complete all as specified. \nNote:- The demolished material should be disposed off out side the MOD land. The contractor shall quote his rates considering this above factor. | | 45 | Cum |
|---|
| 7 | 7 | Demolition of lime / cement concrete of Roofs, floors of any description and in any position not otherwise specifically provided for all as completed.\nNote:- The demolished material should be disposed off out side the MOD land. The contractor shall quote his rates considering this factor. | | 27 | Cum |
|---|
| 8 | 8 | Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified. \nNote:- The demolished material should be disposed off out side the MOD land. The contractor shall quote his rates considering this factor. | | 114 | Sqm |
|---|
| 9 | 9 | Taking down door / window frames with shutters not exc 1.50 sqm each (without taking off shutters from frame) and removing from site complete all as specified and directed. | | 12 | Each |
|---|
| 10 | 10 | Taking down of chowkhat or frames exc 1.50 sqm but n exc 4.0 Sqm withotut taking of shutters from frame and removing from site complete all as specified and directed. | | 5 | Each |
|---|
| 11 | 11 | Dismantling of wall / ceiling boards (fibre, PVC, Pulp, insulation etc ) of any description, any thickness including frame / grid, fillets work etc complete all as specified and directed. | | 232 | Sqm |
|---|
| 12 | 12 | S&F 6 mm thick Asbestos cement corrugated sheet in roof, fixed with J or L hook or cranked bolt with washers.complete all as specified and directed. | | 120 | Sqm |
|---|
| 13 | 13 | Fixing only 6 mm thick Asbestos cement corrugated sheet in roof, fixed with J or L hook or cranked bolt with washers in small areas. complete all as specified and directed.\nNote: old serviceable AC sheets retreived by taking down vide respective item of this schedule shall be re-used. | | 30 | Sqm |
|---|
| 14 | 14 | S&F Asbestos cement two-piece adjustable plain wing ridge 6mm thick, fixed in repairs with J or L hook or cranked bolt with washers. complete all as specified and directed. | | 25 | RM |
|---|
| 15 | 15 | S&F mild steel work as in Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.including cutting tops to shape as directed, embeding in concrete and screwing etc, wind ties for roof including bolts drilling holes, notching for wire etc, flat iron fillets (for securing GI sheet etc) and including all necessary drilling or cutting holes in brick/ concrete surfaces and making good, welding work, bolting or reveting etc and similar work conforming to Fe-290 Gde E-165 complete all as pecified and directed. | | 201 | Kg |
|---|
| 16 | 16 | M&L mild steel work as in Hand rails, half round or other stock section, for doors, balusters, nosing to steps incl embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc.,and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. | | 25 | Kg |
|---|
| 17 | 17 | Supply and fixing 0.63mm thick galvanised, corrugated mild steel sheeting with grade of zinc coating 275 as in roof covering in patches with two corugation side lap, L or J type hooks and washer or fixed with self thread making steel screws of length not less than 75mm with suitable arrangement as required, as in roof, complete all as specified & directed. | | 60 | Sqm |
|---|
| 18 | 18 | Supply and fixing 0.63mm thick galvanised, with grade of zinc coating 275 plain mild steel sheeting as in roof covering/ cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape as requiredand directed at site fixed with L or J type hooks an washer or fixed with self thread making steel screws of length not less than 75mm with suitable arrangement as required, complete all as specified & directed. | | 5 | Sqm |
|---|
| 19 | 19 | M&L preparation of zinc coated / galvanised surfaces of steel or iron, by coating with mordant solution incl washing and cleaning etc., and applying two coats of synthetic enamel paint over a coat of red oxide / zinc chromate primer as in Plain / camouflaging pattern complete all as specified. | | 84.5 | Sqm |
|---|
| 20 | 20 | S&F pre-painted galvalume Aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self taping screws complete all as specified and directed. | | 55 | Sqm |
|---|
| 21 | 21 | S&F pre-painted galvalume Aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self taping screws complete all as specified and directed. | | 25 | Sqm |
|---|
| 22 | 22 | S&F ArmGyp-FB ceiling snow Frost vinyl face, washable metallized polyester foil backing ,vinyl covered edges, suspended ceiling on suspension system. Panels shall be of Size 600 mm x 600 mm x 9 mm, having 7 kg/SQM, including providing Grid system for fixing ceiling tiles shall comprise of suspension system with true horizontal level, suspended on inter locking tegular “Select” system with 15mm black flanges incorporating a 4mm central reveal in black colour and a load carrying capacity of minimum 14.50 kg/m2 with birdsmouth notches metal grid of hot dipped galvanized steel sections consisting of main \"T\" runner with suitably spaced joints to get required length and of size 15x32 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \"T\" of size 15mmx25mm made of 0.30 mm thick (minimum) sheet, 1200mm long spaced between main \"T\" at 600 mm center to center to form a grid of 1200mmx600 mm and secondary cross \"T\" of length 600 mm and size 15mmx25mm made of 0.30 m thick (minimum) sheet to be interlocked at middle of the 1200mmx600 mm panel to form grids of 600mmx600mm and wall angle of size 20mmx15mmx0.3 mm and laying false ceiling tiles of approved texture in the grid including, required fitting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85mm x 30mm x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 15 mm of all T-sections all complete for all heights as per specifications, drawings incl dismantling of old ceiling, all as specified and directed. | | 121 | Sqm |
|---|
| 23 | 23 | S&F in repairs ceiling board of Arm Gyp-FB ceiling snow Frost vinyl face, washable metallized polyester foil backing , vinyl covered edges, suspended ceiling on suspension system. Panels shall be of Size 600 mm x 600 mm x 9 mm , having 7 kg/SQM complete all as specified and directed. | | 45 | Sqm |
|---|
| 24 | 24 | S&F Solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing including dismentelling of sheets complete all as specified . | | 111 | Sqm |
|---|
| 25 | 25 | M&L 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. | | 588 | RM |
|---|
| 26 | 26 | M&L brick work with sub class 'B' old size bricks, of class designation 7.5 all as per IS-1077-1992 (minimum compressive strength of brick 75 kg/Sqcm) straight or curved on plan exceeding 6 mtr mean radius built in cement mortar 1:6, complete all as specified & directed. | | 6 | Cum |
|---|
| 27 | 27 | All as per description of item No. 26.00 here in before but in half brick thick walls built in cement moartar 1:4 | | 12 | Sqm |
|---|
| 28 | 28 | M&L rendering 5mm thick cement mortar 1:4 mixed with water proofing compound as per manufactuer's instructions over and including 10mm thick rendering in cement mortar 1:4 on brick work or concrete surfaces finished even and fair without using extra cement complete all as specified. \nNote : Water proofing compound shall be measured and paid for separately as 'Supply only' under respective item of this schedule. | | 115 | Sqm |
|---|
| 29 | 29 | Supply only liquid water proofing compound conforming to relevant IS complete all as specified and directed. | | 12 | Litre |
|---|
| 30 | 30 | M&L rendering 15mm thick cement mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified. | | 100 | Sqm |
|---|
| 31 | 31 | M&L rendering 10mm thick cement mortar 1:3 on concrete surfaces of ceiling, finished even and smooth without using extra cement complete all as specified. | | 35 | Sqm |
|---|
| 32 | 32 | M&L preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed. | | 40 | sqm |
|---|
| 33 | 33 | M&L preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. | | 35 | sqm |
|---|
| 34 | 34 | M&L preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali restant primer complete all as specified and directed. | | 60 | sqm |
|---|
| 35 | 35 | Taking down of bird netting of hangers at height exc 6.0 metre but n exc 10 metre and refixing in the same position including necessary repair to nettting complete all as specified and directed. | | 350 | Sqm |
|---|
| 36 | 36 | Supply and fixing as in repairs anti bird net, Square mesh size 20 mm x 20mm, Black / White HDPE knotted Net, thickness of the net 1.00mm, Weatherproof, U.V. stabilized and chemically inert, Breaking strength of 23.08 kg per yarn, Having a Melting point of 260°C fixed with boarder rope of dia 4mm, UV stabilized boarder rope jointed with the net by machine inter locking process using three twinces of the same as that of net tied to 12mm dia Hooks (made to shape) or welded to steel structure and 12 mm dia ancher fastner bolt fixed to RCC structure as applicable at suitable intervals complete all as specified and directed. | | 375 | Sqm |
|---|
| 37 | 37 | M&L Repair to de-railed sliding steel gate, over all size 24.80m x 8.40m having 06 leafs of size 4.10 m x 8.2 m each, for smooth functioning of gate by welding where required, dismantling, staightning and refixing in position damaged steel members, cutting and levelling bottom unlevelled PCC stucking to steel members to steel rollers tightening / replacing of worn out nuts & bolts, welding and re adjusting / replacing top / bottom steel rollers, greasing to all movable parts complete all as specified and as directed.\nNote : (i) T&P required for taking down the door for repair and re-fixing the same shall be arranged by the contractor at his own and the unit rate quoted shall include the cost thereof. No clam whatsoever on this account shall be entertained.\n(ii) Replacement of defective steel members, items shall be measured and paid as 'Supply only' against respective item of this schedule.\n\n | | 5 | Each Job |
|---|
| 38 | 38 | All as per item No. 37 here-in-before but over all size of gate 16.0m x 6.0 mtr having 04 leafs of size 4.0 m x 6.0 m each. | | 4 | Each Job |
|---|
| 39 | 39 | Repairing of rolling shutter, push type, size n.exc 6sqm each for smooth functioning by re-posting of laths, riveting to old defective rivets, tightning nuts and bolts, re-stretching of spring, greasing to movable parts and at guide channel including taking out and re-fixing rolling shutter in position complete all as specified and directed.\nNote : (i) T&P required for taking down the door for repair and re-fixing the same shall be arranged by the contractor at his own and the unit rate quoted shall include the cost thereof. No clam whatsoever on this account shall be entertained.\n(ii) Replacement of defective steel members, items shall be measured and paid as 'Supply only' against respective item of this schedule.\n | | 5 | Each Job |
|---|
| 40 | 40 | All as per description of item No 39 here-in-before but size of rolling shutter exc 6sqm but n.exc 15 Sqm. | | 5 | Each Job |
|---|
| 41 | 41 | S&F as in repairs mild steel plain sheet covering to door shutter and top cover of rolling shutter cover cut to size, edges beaded as directed, holes punched all as specified and directed. | | 10 | Kg |
|---|
| 42 | 42 | S&F as in repairs rolling shutter push pull or manual type with 1.00mm thick lath without ball bearing as specified including top cover anchoring rod, hasp and staple and one shop coat of primer and erected in position as indicated all as specified and directed | | 10 | Sqm |
|---|
| 43 | 43 | Supply only MS spring suitable for rolling shutter up to 6 Sqm | | 5 | Each |
|---|
| 44 | 44 | All as per serial item No. 43 here-in-before but suitable for rolling shutter of size exc 6 Sqm but n.exc 15 sqm | | 5 | Each |
|---|
| 45 | 45 | Supply only MS ball bearing suitable for rolling shutter up to 15 Sqm | | 5 | Each |
|---|
| 46 | 46 | Supply only gear assembly suitable for rolling shutters fixed in position all as specified. | | 1 | Each set |
|---|
| 47 | 47 | Supply only mild steel section of any size or any section including necessary cutting & drilling holes as required. | | 10 | Kg |
|---|
| 48 | 48 | Supply only mild steel solid rollers of any dia or section complete all as specified . | | 50 | Kg |
|---|
| 49 | 49 | M&L MS work as in pintel hooks, brackets etc incl necessary cutting welding, drilling holes confirming to Fe-290 (Gde E-165) complete all as specified. | | 10 | Kg |
|---|
| 50 | 50 | M&L Cutting holes in brick walls built in cement mortar, superficial area n.exc 150 Sqcm incl making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required all as specified and directed. | | 450 | Per centimeter depth (of cutting) |
|---|
| 51 | 51 | All as per serial item No 50.00 here in before but cutting in superficial area exceeding 150 Sqcm but not exceeding 400 Sqcm. | | 450 | Per centimeter depth(of cutting) |
|---|
| 52 | 52 | Taking down aluminium shutter / sliding door for necessary repair work and re-fixing in position after adjusting or replacing defective members of rails or styles in position with replacement of steel screw re threading and fixing on existing devices, resetting or replacing top pivots bottom steel plates etc and resetting or replacing glazing etc for proper function of aluminum door of size n exc 1.5 sqm each complete all as specified.\nNote :- Supply only aluminum section, glazing and top pivots shall be measured and paid seperately. | | 15 | Each leaf |
|---|
| 53 | 53 | All as per serial item No. 52.00 here-in-before but over all size of door exc 1.5 sqm but n exc 3.0 sqm each | | 12 | Each leaf |
|---|
| 54 | 54 | Supply only anodised aluminum section as in rail, stiles, frame etc complete all as specified | | 300 | Kg |
|---|
| 55 | 55 | Supply only top pivot of casting body suitable for aluminum door | | 15 | Each |
|---|
| 56 | 56 | S & F as in repairs aluminium anodized grill 6-8mm thick, 85mmx85mm hexagonal shaped mesh, fixed to aluminium frame work with 'U' clip of size 15mmx12mm & fastners complete all as specified and directed. | | 5 | Sqm |
|---|
| 57 | 57 | S & F as in repairs mild steel mortice lock vertical type 100mm, 4 levers all as specified complete all as specified and directed. | | 10 | Each |
|---|
| 58 | 58 | Supply only double action floor door spring hydraulically regulated made up minimum 1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified | | 15 | Each |
|---|
| 59 | 59 | Supply only door closer Aluminium Extruded section hydraulically regulated designation No 03 universal type , suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified | | 12 | Each |
|---|
| 60 | 60 | S & F 4.80 mm thick sheet glass of ordinary quality plain / tinted and glazing with rubber beads, clips etc complete all as specified and directed.\nNote: Cost of rubber beads, clip included in unit quoted rate of this item. | | 18 | Sqm |
|---|
| 61 | 61 | S&F ordinary glass 3mm thick with oil putty in square n exc 0.50 sq in each pane including hacking out of old broken glass complete all as specified and directed. | | 75 | Sqm |
|---|
| 62 | 62 | Disconnecting existing tanks, 500 litre capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) complete all as specified and directed. | | 5 | Each |
|---|
| 63 | 63 | Dismantling of water tanks of capacity 500 litres of any description complete all as specified and directed. | | 5 | Each |
|---|
| 64 | 64 | Supply and fixing 500 ltr capacity rotational moulded polythelene water storage tank (clyndrical vertical with closed top) tripple layered white, hoisted and fixed in position complete all as specified and directed. | | 5 | Each |
|---|
| 65 | 65 | S&F 20mm PTMT nipple suitable for HDPE water tank (minimum weight 45gms) complete all as specified . | | 6 | Each |
|---|
| 66 | 66 | S&F in repair 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. | | 10 | Each |
|---|
| 67 | 67 | S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia complete all as specified and directed. | | 25 | Each |
|---|
| 68 | 68 | Taking up or down 15 mm bore steel tubing and connection and removal from site complete all as specified and directed. | | 35 | RM |
|---|
| 69 | 69 | Taking up or down 20 mm bore steel tubing and connection and removal from site complete all as specified and directed. | | 50 | RM |
|---|
| 70 | 70 | S&F 15mm bore, steel water tubing, medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floor complete all as specified and directed. | | 35 | RM |
|---|
| 71 | 71 | S&F 20mm bore, steel water tubing, medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floor complete all as specified and directed. | | 40 | RM |
|---|
| 72 | 72 | Fixing only 20mm bore, steel water tubing, medium grade, galvanised with all new fittings and fixed complete to walls and ceiling or laid in floor complete all as specified and directed.\nNote:- Old servicable tubing obtained by taking down shall be re-used. cost of new fittings shall bed deemed included in unit quoted rate. | | 10 | RM |
|---|
| 73 | 73 | S&Fas in repairs angle / stop cock, cast copper alloy, high pressure 15mm bore chromium plated with wall flange, screwed down both side for iron pipe or for unions and fixed complete all as specified and directed. | | 14 | Each |
|---|
| 74 | 74 | S&F as in repairs bib tap brass, fancy type chromium plated with long shank & wall flange cap, screwed down screwed for iron pipe 15mm bore and fixed complete all as specified and directed. | | 45 | Each |
|---|
| 75 | 75 | S&F as in repairs pillar tap cast copper alloy with chromium plated fancy type screwed down high pressure with lettered 'Hot' or 'Cold' with long shanks and fly nuts screwed for iron pipe 15mm bore complete all as specified and directed. | | 12 | Each |
|---|
| 76 | 76 | S&F as in repairs Health faucet with 1.5mm flexible chromium plated tube and hook fixed to angle valve etc complete all as specified and directed. \n | | 5 | Each |
|---|
| 77 | 77 | S&F as in repairs 450 mm long PVC connection 15 mm bore with PTMT nuts complete all as specified and directed . | | 6 | Each |
|---|
| 78 | 78 | S&F as in repairs flush pipe of polyethylene of low or high density 32mm dia for WHB / urinal pot including connecting complete all as specified and directed. | | 2 | Each |
|---|
| 79 | 79 | S&F as in repairs Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed. | | 2 | Each |
|---|
| 80 | 80 | Supply & fixing as in repairs chromium plated brass shower rose with or without swivel joints 125mm dia including fixing to steel pipe, complete all as specified. | | 2 | Each |
|---|
| 81 | 81 | M&L 75mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregates for sub bases of floor, surface finished even and rough to receive floor topping completet all as specified . | | 360 | Sqm |
|---|
| 82 | 82 | M&L 75 mm thick PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in floors, surface finished even and smooth without using extra cement complete all as specified and directed. | | 50 | Sqm |
|---|
| 83 | 83 | M&L 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregates for sub floors and sub bases for filling undulation under floor tiles or other similar complete all as specified . | | 90 | Sqm |
|---|
| 84 | 84 | M & L 40 mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregates as in floors including finishing concrete surfaces even and smooth using extra cement complete all as specified . | | 50 | sqm |
|---|
| 85 | 85 | S&F Glass dividing strips width of 38 mm and 3 mm thick inserting in position as per design in floors complete all as specified and directed. | | 50 | RM |
|---|
| 86 | 86 | M&L non skid coloured ceramic tiles 7 to 8mm thick (squared or rectangular ) area of each exc 0.11 sqm but not exc 0.18 sqm as in floor set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified. | | 150 | Sqm |
|---|
| 87 | 87 | M&L vitrified ceramic coloured tiles 9 to 10mm thick double charged light shade of size 600mmx600mm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. | | 90 | Sqm |
|---|
| 88 | 88 | M&L vitrified ceramic coloured tiles 9 to 10mm thick double charged light shade as in skirting set & jointed in neat cement slurry and pointed in white or coloured cement to match over a backing plaster 10mm thick in cement mortar 1:4 complete all as specified and directed. | | 7 | Sqm |
|---|
| 89 | 89 | Demolition of stone slabs of any description or thickness in roof, floors, suspended slabs, chajjas etc, laid, bedded and pointed in any mortar complete all as specified. | | 1.7 | 10 Sqm |
|---|
| 90 | 90 | M&L granite stone slab 20mm thick as in kitchen platform / flooring / wash basin counters etc., laid over and including 20 mm thick screed bed in cement mortar 1:6 and jointed and pointed with grey cement mixed with pigment to match the shade of stone including cutting opening (of any shape and size), including cutting, rubbing and polishing surface, shade of granite stone as approved by GE completed all as specified and directed.\nNote:- Back side of stone slab shall be made rough by applying a layer of araldite adhesive and spraying sand as directed. The cost thereof shall be deemed included in unit quoted rate. of this item. | | 17 | Sqm |
|---|
| 91 | 91 | M&L granite stone slab 20mm thick as in vertical surfaces over and including 10 mm thick rendering in cement mortar 1:4, jointed and pointed in grey cement mixed with pigment to match the shade of stone including cutting rubbing and polishing surface, shade of granite stone as approved by GE completed all as specified and directed.\nNote:- Back side of stone slab shall be made rough by applying a layer of araldite adhesive and spraying sand as directed. The cost thereof shall be deemed included in unit quoted rate. of this item. | | 12 | Sqm |
|---|
| 92 | 92 | Rounding of edges of gratine stone slabs 20mm thick by grinding and rubbing and finished smooth complete all as specified and directed.\nNote:- Each edge shall be measured and paid for separately. | | 25 | RM |
|---|
| 93 | 93 | M&L coloured chequered cement concrete tiles 25cmx25cmx25mm thick machine pressed set, jointed and pointed in neat cement slurry and pointed with mixture of grey cement and white cement in equal proportions with pigment in floors laid over and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed. | | 120 | Sqm |
|---|
| 94 | 94 | M&L 50 mm thick PCC (1:3:6) type C-1, using 20mm graded stone aggregate as in plinth protection, laid in bays and surfaces finished even & fair,including filling the joints with bitumen mastic complete all as specified & directed. \nNote:- The plinth protection shall be laid in pannels and length of the each panel shall not be more than 2.00 mtr all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided and cost thereof shall be deemed included in unit rate . No deduction for joints shall be made while making payment against the above item. | | 210 | Sqm |
|---|
| 95 | 95 | M&L glazed coloured ceramic tiles (300mmx450mm)x7-8mm thick as in vertical surfaces of walls, set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified. | | 95 | Sqm |
|---|
| 96 | 96 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. | | 107 | RM |
|---|
| 97 | 97 | S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required, complete all as specified. | | 95 | RM |
|---|
| 98 | 98 | S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed. | | 7 | RM |
|---|
| 99 | 99 | S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed. | | 5 | RM |
|---|
| 100 | 100 | S&F 75mm dia PVC (SWR) floor trap / nahani plain with CP grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified. | | 4 | Each |
|---|
| 101 | 101 | S&F 75mm dia PVC (SWR) junction single (single T), equal or un equal including jointing with solvant cement as required complete all as specified. | | 1 | Each |
|---|
| 102 | 102 | S&F 100mm dia PVC (SWR) bend with oval access door, fixed as required including jointing with solvant cement complete all as specified. | | 2 | Each |
|---|
| 103 | 103 | S&F 75mm dia PVC (SWR) bend fixed as required including jointing with solvant cement complete all as specified. | | 2 | Each |
|---|
| 104 | 104 | S&F 75mm dia PVC (SWR) bend fixed as required including jointing with solvant cement with oval access door complete all as specified. | | 2 | Each |
|---|
| 105 | 105 | S&F 100mm dia PVC (SWR) cowl including jointing with solvant cement fixed as required complete all as specified. | | 2 | Each |
|---|
| 106 | 106 | Roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust etc and including brushing neat cement slurry with 3 Kg/Sqm in roofs,complete all as specified and directed | | 270 | Sqm |
|---|
| 107 | 107 | M&L cutting grooves in brick wall for inserting APP membrane and other works, size of groove 75mm wide and 65mm deep and shaping horizontal face of grooves and making good with cement mortar 1:3 or PCC 1:2:4. all as specified and directed. | | 155 | RM |
|---|
| 108 | 108 | M&L Cement concrete 1:2:4 type B0,(using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops, on junction of parapet, coping etc cement concrete surface finished even and smooth without using extra cement complete all as specified and directed. | | 1.1 | Cum |
|---|
| 109 | 109 | M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in padding over roof over old RCC roof surfaces and the surface finished even & smooth without using extra cement complete all as specified and directed . | | 13.5 | Cum |
|---|
| 110 | 110 | M&L 15 mm thick plaster in cement mortar 1:4 mixed with liquid water proofing compound @ 200ml per 50 Kg of cement, on concrete surfaces of roofs finished even and smooth without using extra cement and complete all as specified and directed. \nNote:- Water proofing compound shalll be measured and paid for seperately under respective item of this schedule. | | 270 | Sqm |
|---|
| 111 | 111 | M&L APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (wt. not less than 150 gms/Sqm ) laid by torch forced application over a coat of bitumen 85/25 grade applied hot @ 1.20 Kg/Sqm laid over and including a priming coat using btuminious primer @0.40 litre / sqm, complete all as specified and directed. \n | | 270 | Sqm |
|---|
| 112 | 112 | M&L 20mm thick Pre-cast cement concrete tiles 1:2:4 type B-1, (10mm to 12.5mm graded stone aggregate), bedded and jointed over and including 15 mm thick screed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified and directed . | | 270 | Sqm |
|---|
| 113 | 113 | S&F plain framed panelled shutters, 35 mm thick 2nd class hard wood (any numbers of panels) with with panels of timber flat on both sides (feather edged) or of veneered parcticle board medium density,wood parcticle board with commercial face veneers all as specified and as directed. | | 9 | Sqm |
|---|
| 114 | 114 | S&F solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforcement with MS square tube supply & fixing in opening as per specifications. | | 27 | RM |
|---|
| 115 | 115 | M&L factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottam rail both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges paneling of prelam solid PVC sheets 10mm thick to be filted in MS frame welded, sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with the solvent cement complete all as specified in SSR Part-II. | | 7.5 | Sqm |
|---|
| 116 | 116 | S&F 200mm long aluminum anodized barrel tower bolt of extruded section all as specified and directed. | | 16 | Each |
|---|
| 117 | 117 | S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type), 300mm length of bolt, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed | | 11 | Each |
|---|
| 118 | 118 | S&F stainless steel butt hinge 100mm size, medium weight cold rolled & fixed to MS steel frame by welding or to PVC frame by screwing complete all as specified and directed. . | | 15 | Each |
|---|
| 119 | 119 | S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed. | | 18 | Each |
|---|
| 120 | 120 | M&L prepapration of new or previously untreated surfaces of wood or wood based materials of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of pink primer comlplete all as spd and as directed. | | 23.4 | Sqm |
|---|
| 121 | 121 | S&F extruded Alumminium handles 150mm size, cast type, anodised complete all as specified | | 22 | Each |
|---|
| 122 | 122 | Supply and fixing door stopper hanging type, aluminium anodised natural shade matt finish with quality rubber of size 140mm complete all as specified and directed. | | 45 | each |
|---|
| 123 | 123 | S&F factory made Steel windows 1.25 mm thick Box type (primer coated) ERW hollow ‘P’ section of size 60mmx25mm single rebated comprises of glazed and guaged skeleton shutters, EWR Sec 50mmx20mm and 1mm thick and two open able leaf consisting two Nos sash bar of ‘T’ section 20mm x 3mm complete welded to frame with one vertical mullion of EWR box type ‘T’ section of size 60mmx25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 using 20mm graded stone aggregate, four Nos for each window including following fittings welded to framed shutter complete all as shown in drawing No. TD-219 sheet 1/3 to 3/3 of chief Engineer Chandigarh Zone :- \n(a) Holdfasts 150mm long 12mmx3mm made to shape per window -04 Nos, \n(b) Handle of Z Sec 20mmx25mm, 100mm long per leaf-01 No, \n(c) MS tower bolt 150mm long per leaf -02 Nos,\n(d) ‘Z’ sec 20mm x 25mm, 100 long stopper per leaf -01 No, \n(e) Cleat 55 mm long of hollow square 15mmx20mmx63mm welded to hinges per leaf -01 No, \n(f) MS pintal hinges of size 75mmx12mm per leaf -02 Nos. \n(g) One shop coat of zinc oxide on all steel surfaces complete all as specified.\nNote:- \n(i) Set of two single rebated windows with shutters & fittings shall be measured as one unit.\n(ii) Wire guage and sheet glass shall be measured and paid for separately under respective item of this schedule. | | 4 | Sqm |
|---|
| 124 | 124 | All as per description of item No. 123.00 here in before but ventrilators with top / side hung shutters | | 2 | Sqm |
|---|
| 125 | 125 | S&F mild steel work as in door frames, window guard bars fixed independently and similar articles conforming to Fe-290 Gde-165 complete all as specified | | 80 | Kg |
|---|
| 126 | 126 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, cut nails, GI wire staple or with wooden beading all as specified and directed. | | 5 | Sqm |
|---|
| 127 | 127 | M&L preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. | | 39 | Sqm |
|---|
| 128 | 128 | All as per description of item No. 127.00 here in before but only two coats of synthetic enamel paint on previously primed surfaces | | 6 | Sqm |
|---|
| 129 | 129 | M&L preparation of newly plastered or unplastered surfaces and applying two coats of acrylic emulsion exterior quality over a coat of primer exterior grade tint in camouflaging pattern as approved by GE complete all as specified and diretced. | | 115 | Sqm |
|---|
| 130 | 130 | Supply and fixing as in repairs PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including PVC connection and 32mm dia PVC long bend for squat pattern etc, set with concrete and making good to floor including taking down existing, fixed as in repairs complete all as specified & directed. | | 3 | Each |
|---|
| 131 | 131 | S&F as in repairs Table top wash hand basin Vitreous china, light colour / white of size 565mmx420mmx140mm including brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets, 32mm bore PVC waste pipe of appropriate length ilcluding making necessary connections complete all as specified and directed.\n | | 3 | Each |
|---|
| 132 | 132 | Supply and fixing in repairs towel rail PTMT, 600mm long, fixed with chromium plated brass screws and plastic cleats complete all as specified | | 5 | Each |
|---|
| 133 | 133 | S&F as in repairs bevelled edged mirror of size 600mm x 450mm of selected quality glass mounted on 6mm thick AC plain building board or commercial plywood and fixed to wooden plug with chromium plated brass screws and cup washers complete all as specified | | 5 | Sqm |
|---|
| 134 | 134 | S&F as in repairs vitreous china urinal, half stall type, of size 600mm x 360mm x 280mm, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement but including waste pipe, coupling and CP urinal spreader complete all as specified and directed. | | 3 | Each |
|---|
| 135 | 135 | S&F 100mm dia PVC (SWR) bend, any radius as required fixed as required including jointing with solvant cement complete all as specified. | | 15 | Each |
|---|
