Making Arrangement Of Water Supply Distribution System Including Providing Pressure Filter ( 8Cum/Hr ) , Pipeline , Sump , Fencing , Store Room And Other Misc . Works At Penganga Ocp Of Wani Area .

Tender Notice

25502903
Making Arrangement Of Water Supply Distribution System Including Providing Pressure Filter ( 8Cum/Hr ) , Pipeline , Sump , Fencing , Store Room And Other Misc . Works At Penganga Ocp Of Wani Area .
Indian
Maharashtra
21-09-2020
08-10-2020
09-10-2020

Tender Details

Making Arrangement Of Water Supply Distribution System Including Providing Pressure Filter ( 8Cum/Hr ) , Pipeline , Sump , Fencing , Store Room And Other Misc . Works At Penganga Ocp Of Wani Area .

Key Value

Document Fees
Refer document
EMD
INR 58500.00 /-
Tender Value
Refer document

BOQ Items

Name of the Work / Contract No:
Sl. No. Item Description Item Code / Make Quantity Units
1 1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.All kinds of soil 915.82 Cum
2 2 Supplying and filling in plinth with (local) sand under floors, including watering, ramming, consolidating and dressing complete. 10.87 Cum
3 3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size). 10.87 Cum
4 4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 7.39 Cum
5 5 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 10.84 Cum
6 6 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 17.06 Cum
7 7 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size 11.31 Cum
8 8 Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level.Thermo Mechanically Bars 2744.7 Kg
9 9 Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete 8.48 Sqm
10 10 Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc 160 Sqm
11 11 Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts 16.56 Sqm
12 12 Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers 22.24 Sqm
13 13 Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and acces platform 72 Sqm
14 14 Brick work with flyash bricks of Non Modular in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 10.46 Cum
15 15 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 116.67 Sqm
16 16 6 mm cement plaster of mix 1:3 (1 cement : 3 fine sand) 18.51 Sqm
17 17 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)\n 15.3 Kg
18 18 Providing and fixing ISI marked flush door shutters confirming to IS 2202 (Part I) non-decorative type, core of block board construction with frames of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick shutters including ISI marked Stainless Steel butt hinges with necessary screws. 1.89 Sqm
19 19 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminium (minimum thickness of powder coating 50 micron) 16.65 Kg
20 20 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness 1.92 Sqm
21 21 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding 86.4 Kgs
22 22 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete 250x16 mm 4 No
23 23 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete 250x10 mm 2 No
24 24 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete 125 mm 4 No
25 25 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar,bent to shape with hooked ends in R.C.C. slabs or beams during laying,including painting the exposed portion of loop, all as per standard design complete. 2 Nos
26 26 Finishing walls with acrylic smooth exterior paint of required shade: New work (Two or more coats applied @ 1.67 ltr/10 sqm over and i/c priming coat of exterior primer applied at @ 2.20 Kg/sqm) 58.34 Sqm
27 27 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer 58.34 Sqm
28 28 White washing with lime to give an even shade :New work (three or more coats)\n 18.51 Sqm
29 29 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work 68.88 Sqm
30 30 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 977.88 Kg
31 31 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 60.5 Sqm
32 32 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 780 Kg
33 33 Providing & Supplying of Side stream filter of capacity 8 M3 / Hr dicharge,With 900 mm dia and height of straight 1500mm, shell end thickness 8mm, Quantity of filter media 1450 Kg, CI valves complete with required pressure Guage including transportation, testing Installation and running charges etc complete as per instrution of EIC. 2 No
34 34 Providing ISI mark G.I. pipe of following class and dia.excluding GST levied by GOI and GOM in all inspection charges transportation to stores etc complete as per IS 1239/2004. One coupler shall be provided with each full length of pipe cost of which is included in rates below. Heavy pipe 100 mm dia of weight 14.70 Kg/m 1500 Rmt
35 35 Lowering, laying and jointing G. I. pipes and specials of following class and diameter including conveyancefrom stores to site of works, all labour, etc. complete either underground or in vertical position, as directed by Engineer-in-charge. Heavy pipe 100 mm dia 1500 Rmt
36 36 Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including testing of joints :100 mm diameter pipe 184 Nos
37 37 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc 25 mm dia nominal bore 150 Mtr
38 38 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.50 mm dia nominal bore 150 Mtr
39 39 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.80 mm dia nominal bore 100 Mtr
40 40 Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including testing of joints :80 mm diameter pipe 12 Nos
41 41 Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 100 mm Dia 3 Nos
42 42 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) 100 mm diamater Class I 5 Nos
43 43 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 80 mm Nominal Bore 5 Nos
44 44 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm Nominal Bore 5 Nos
45 45 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm Nominal Bore 5 Nos
46 46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 50mm Nominal Bore 4 Nos
47 47 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore 4 Nos
48 48 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore 4 Nos
49 49 Supplying and erecting 1 phase, 230 V, 50 Hz, submersible pump set suitable for erection on open well, pump having discharge 130 / 475 L.P.M., head 21 / 9 m & delivery pipe of necessary diameter erected withnecessary H type clamps as per specification No. WP-OSP \n 2 No
50 50 Supplying and erecting submersible pump set suitable for erection on open well of required HP with 415 V 50 c/s.A.C. supply, having elivery head from 21 to 7 m and discharge from 200 to 800 Itrs. per minute (Max efficiency at 16 m head & 500 Itr discharge) & delivery pipe of necessary diameter erected with necessary H type clamps as per specification No. WP-OSP 2 No
51 51 Supplying and erecting submersible pump set suitable for erection on open well of required HP with 415 V 50 c/s.A.C. supply, having delivery head from 36 to 18 m and discharge from 400 to 1000 Itrs. per minute (Max efficiency at 29 m head & 680 Itr discharge) & delivery pipe of necessary diameter erected with necessary H type clamps as per specification No. WP-OSP 2 No
52 52 Supplying and erecting D.O.L. Starter 400V. 3 phase, 50 cycles with no volt coil and overload element with necessary materials and connected to supply upto 7.5 H.P. (Similar to L & T make DOL Model) 2 No
53 53 Supplying and erecting fully Automatic star/delta starter suitable for 12.5 H.P. to 15 H.P. for 3 phase squirrel cage motor totally enclosed with overload and no volt relay complete erected on provided angle iron frame. (similar to L & T make MK-1 FASD model.) 2 No
54 54 Supplying and erecting fully Automatic star / delta starter suitable for above 25 H. P. to 35 H. P. squirrel cage motor totally enclosed with overload and no volt relay complete erected on provided angle iron frame. (similar to L & T make MN 32 FASD model .) 2 No
55 55 Supplying and erecting flat flexible 3 core 4 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. 60 m
56 56 Supplying and erecting flat flexible 3 core 6 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. 60 mtr
57 57 Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete 150 mtr
58 58 Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 10000 Liter
59 59 Supplying & erecting Centrifugal water pump (Monoblock), 230V, Single phase 50 cycles A.C. supply of 1 HP of specified discharge head & size of suction, delivery pipes on provided C.C. foundation as per specification No. WP-CGP 1 No
60 60 Total impact of GST for the purpose of CTC 1 Nos
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2020 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail