| 1 | 1 | Dismantling Brick Work, Tile Masonry or Tile Lining and Tile | | 0.05 | Cum |
|---|
| 2 | 2 | Terracing. (b) In cement. (HSR 8.5 (b) | | | |
|---|
| 3 | 3 | Dismantling cement conglomerate/ terrazzo floors 25mm to | | 98.03 | Sqm |
|---|
| 4 | 4 | 50mm thick including concrete base. (HSR 8.25) | | | |
|---|
| 5 | 5 | Dismantling brick or flagged stone slab flooring without | | 98.87 | Sqm |
|---|
| 6 | 6 | Concrete base. (HSR 8.28) | | | |
|---|
| 7 | 7 | Cement concrete 1 : 8 : 16 with brick ballast 40 mm nominal | | 14.99 | Cum |
|---|
| 8 | 8 | size in first storey upto 4 metres above plinth level. (HSR 10.44) | | | |
|---|
| 9 | 9 | Cement concrete 1:1.5:3 with stone aggregate 20mm nominal | | | |
|---|
| 10 | 10 | size for reinforced concrete work in shelves excluding steel | | | |
|---|
| 11 | 11 | reinforcement, but including centring and shuttering, laid in position, complete in all respect. (HSR 10.81 + 10.95 (a) | | | |
|---|
| 12 | 12 | 1st floor | | 0.29 | Cum |
|---|
| 13 | 13 | 2nd floor | | 1.37 | Cum |
|---|
| 14 | 14 | 11.43cm thick brick wall laid in cement sand mortar 1:4 in superstructure. (HSR 11.48 a) | | 30.82 | Sqm |
|---|
| 15 | 15 | Providing and laying Baroda Green marble stone 17mm and | | 4.31 | Sqm |
|---|
| 16 | 16 | above thick in risers of step, skirting, dado, pillars and wall | | | |
|---|
| 17 | 17 | lining included matching the grains of marble slab in any pattern | | | |
|---|
| 18 | 18 | as specified laid over 12mm thick cement sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match | | | |
|---|
| 19 | 19 | the shade of marble including rubbing and polishing. The sample shall be got approved from Engineer-in-Charge for all heights/ storey. (HSR 14.98) | | | |
|---|
| 20 | 20 | Providing & fixing ceramic tiles/ anti skid tile of size 400mm x 400mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. \nNote: - Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSON, RAK AND SIMPOLO. (HSR 14.91)\nNote:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. | | 307.8 | Sqm |
|---|
| 21 | 21 | Plastering on under side of ceiling 10mm thick cement plaster 1:4. (HSR 15.52) | | | |
|---|
| 22 | 22 | 1st floor | | 3.85 | Sqm |
|---|
| 23 | 23 | 2nd floor | | 13.6 | Sqm |
|---|
| 24 | 24 | Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR 16.1) | | 3.45 | Sqm |
|---|
| 25 | 25 | Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.2) | | 3.45 | Sqm |
|---|
| 26 | 26 | Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.3) | | 4.39 | Sqm |
|---|
| 27 | 27 | Applying priming coat with metal primer on New steel or iron work including preparation of surface. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.9) | | 150.74 | Sqm |
|---|
| 28 | 28 | Painting two coats excluding priming coat with ready-mixed paint for metallic surfaces in all shades on new steel or iron work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.17) | | 150.74 | Sqm |
|---|
| 29 | 29 | Preparation of plastered surfaces for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler,consisting of white lead, linseed oil, varnish and chalk mittii including finishing Preparation of plastered surfaces for oil bound distemper including sand papering. (HSR 16.52) | | 17.45 | Sqm |
|---|
| 30 | 30 | Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58) | | 17.45 | Sqm |
|---|
| 31 | 31 | Cost of iron fittings, complete for doors and windows, such as tower bolts, handles, etc and screws for these fitting (excluding sliding bolt). (HSR 17.71) | | | |
|---|
| 32 | 32 | for single lead shutter. | | 1.38 | Sqm |
|---|
| 33 | 33 | Providing and fixing sliding bolt with nuts and screws etc. complete. (b) Aluminium. (ii) size 250 mm x 16 mm. (HSR 17.83 (b) (ii) | | 1 | No. |
|---|
| 34 | 34 | Factory manufactured solid flush door shutters, with block board core as per IS 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot pressed, confirming to IS 2202 part I and II, fixed in position, including iron hinges, screws, chocks/ cleats and stops, etc (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (a) commercial veneering with vertical grains or corss bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (iii) 35mm thick. (HSR 17.93 (a) (iii) - Note 17.18 (i) | | 1.38 | Sqm |
|---|
| 35 | 35 | Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12) | | 5.79 | Qtl. |
|---|
| 36 | 36 | Providing and fixing hard drawn steel wire fabric 75mm x 25mm rectangular mesh with 3.25mm dia wire fixed on steel windows of standard rolled sections with 3mm thick flat iron cover moulding of 12.50mm width fixed with machine screws welded complete in all respect. (HSR 18.33) | | 150.74 | Sqm |
|---|
| 37 | 37 | Pressed steel sheet frames (chowkats), consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete:- (a) door and window frame of size 89mm x 50mm with 40mm wide single rebate. (HSR 18.34 (a) | | 4.95 | Rmt |
|---|
| 38 | 38 | P.H. work | | | |
|---|
| 39 | 39 | Providing & fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal Work - Exposed on Wall. (DSR 18.10) | | | |
|---|
| 40 | 40 | 20mm internal diameter of pipeline. | | 179.6 | Rmt |
|---|
| 41 | 41 | Providing and fixing in position 32mm dia G.I. Waste pipe Embedded in wall or lead waste pipe (weighing 3.47 kg. per metre and 2.8mm thick) upto floor Level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge). (HSR 30.48) | | 24 | Nos. |
|---|
| 42 | 42 | Providing and fixing in position best Indian make Vitreous Chinaware Sinks with complete fittings as fully described in item no. 30.51 above. (a) White. (ii) Size 600mm x 450mm x 250mm. (HSR 30.52 (a) (ii) | | 24 | Nos. |
|---|
| 43 | 43 | Providing and fixing 15 mm C.P brass Laboratory cock swan neck of best quality (to the approval of the Engineer-in-charge. (b) Two way. (HSR 30.78 (b) | | 24 | Nos. |
|---|
| 44 | 44 | Providing and fixing in position best Indian make flexible tube connection. (b) C.P Brass. (iii) 15mm x 450mm. (HSR 30.82 (b) (iii) | | 24 | Nos. |
|---|
| 45 | 45 | Providing and fixing HDPE Water Storage Tanks of Sintex, Diplast, O.K. supreme make with covers/ lids marked with IS: 12701 on roof top of buildings including cost of hoisting and | | 2 | Nos. |
|---|
| 46 | 46 | placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for | | | |
|---|
| 47 | 47 | connections in tanks complete in all respect to the satisfaction of Engineer-in-Charge. (except civil work). (e) 1000 Ltr. Capacity. (HSR 30.119) | | | |
|---|
| 48 | 48 | Providing & fixing 1/2\" Hard Copper Gas Pipe with Jhiri & Insulatation complete in all respect as per approval of the Engineer-in-Charge of the work. (NS) | | 545.45 | feet |
|---|
