1 Providing And Fixing Low Height Partitions At Required Location Having Minimum Thickness Of 65Mm Made By Using 50Mm X 50Mm Finished Size Central Province Teak Wood ( Cptw ) Section Framing At 600Mm Center To Center, Covered With 6Mm Thick Marine Ply Confirming To I.S.303 / I.S.710-1980 On Both Sides. The Partition Shall Be Finished With Decorative Laminate Sheet Confirming To I.S.-2046 Finished Lamination Pattern With Or Without Grooves Externally With Necessary Lipping Of Burma Teak Wood, Molding, Anti-Termite Treatment To All Plywood And Wood Work Including All Leads And Lifts Etc. Complete As Per Architects’ Drawing And As Per Instruction Of The Engineer In-Charge. 2 Providing And Fixing Full Height Partitions At Required Location Having Height More Than 1.34M And Minimum 65Mm Thick Made By Using 50Mm X 50Mm Finished Size, Central Province Teak Wood ( Cptw ) Section Framing At 600Mm Center To Center, Covered With 6Mm Thick Marine Ply Confirming To I.S.303 / I.S.710-1980, Veneer Pattern With Or Without Grooves Externally With Necessary Lipping Of Burma Teak Woo ) , Molding, Anti-Termite Treatment To All Plywood And Wood Work With Melamine Polish Including All Leads And Lifts Etc. Complete As Per Architects’ Drawing And As Per Instruction Of The Engineer In- Charge. 3 Providing & Fixing Dias Of Size 500Mm X 600Mm X 450Mm Height With Table Top Of 25Mm Thick Plain Particle Board Of Exterior Grade Confirming To Is-3087 With Post Forming Laminate On Top & Balancing Laminate Below With 2Mm Thick, Pvc Edge-Band Of Required Size, Sides And Bottom Of 25Mm Thick Both Side Prelaminated Particle Board Of Exterior Grade Confirming To Is-12823-1990 With 2Mm Thick Pvc Edge-Band Of Required Size, Required Hardware, Wooden Dowels, Right Angle Connector, Head Screw & Cap Etc. Including All Leads And Lifts Etc. Complete As Per Architects’ Drawing And As Per Instruction Of The Engineer In- Charge. 4 Providing And Fixing Full Height Door Shutter At Required Location Having Height More Than 1.5M Made By Using Solid Core Commercial Type Flush Doors 35Mm Thick With Decorative Laminate Sheet Confirming To I.S.-2046 With Finished Lamination Pattern With Or Without Grooves Externally With Necessary Lipping Of Burma Teak Wood, Molding, Anti-Termite Treatment To Plywood And Wood Work Including All Leads And Lifts Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In-Charge Etc. 5 Providing And Fixing Full Height Door Shutter At Required Location Having Height More Than 1.5M Made By Using Solid Core Commercial Type Flush Doors 35Mm Thick With Veneer Pattern With Or Without Grooves Externally With Necessary Lipping Of Burma Teak Wood, Molding, Anti-Termite Treatment To Plywood And Wood Work With Melamine Polish Including All Leads And Lifts Etc. Complete As Per Architects’ Drawing And Instruction Of Engineer In-Charge. 6 Providing And Fixing 53Cm Deep Cupboard Type Full Height Storage Unit Made Out Of 19Mm Thick Marine Plywood Confirming To I.S.710-1980 For Frames, Internal Verticals, Horizontal Divisions, Shutters And 6Mm & 12Mm Thick Marine Plywood For Drawers With Locks, Handles, Hardware, Lipping & Beading Patti Of Burma Teak Wood ) , Finished With Veneer In Approved Pattern With Grooves And Two Coats Of French Polish Confirming To I.S.-2338 And Melamine Polish For All Molding & Lipping Patties With Anti-Termite Treatment To Plywood & Wood Work Including All Leads & Lifts Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer- In-Charge. 7 Providing & Fixing On Site 40Cm Deep Low Height Storage Unit At Required Location Less Than 1.35M Height By Using 19Mm Marine Ply Confirming To I.S.303 / I.S.710-1980 For Frame, Internal Verticals, Horizontal Divisions, Openable Shutters, 6Mm Thick Marine Ply Back With Necessary Locks, Handles, Hardware, Lipping Of Burma Teak Wood, Molding, Finished With Decorative Laminate Confirming To I.S.-2046 Sheet Finished With Lamination Pattern With Grooves Externally And Two Coats Of French Polish Confirming To I.S.-2338 With Anti-Termite Treatment To Plywood & Wood Work Including All Leads & Lifts Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In Charge. 8 Providing & Supplying Table Of Size 2.13M X 0.91M Made Out Of 19Mm Thick Marine Ply Confirming To I.S.303 / I.S.710-1980, Top Side & Apron Having 38Cm X 54Cm X 75Cm Storage Boxes On Both Sides Made Up Of 19Mm Marine Ply For Sides, Shutters, Horizontal And Vertical Divisions Of 12Mm ( 6Mm X 2 ) Thick Marine Ply Confirming To I.S.303 / I.S701-1980 Back And Three Drawers On One Side Made By Using 19Mm Marine Ply Front And Sides, 6Mm Marine Ply Bottom With Necessary Lipping Of Burma Teak Wood, Moldings And C.P.T.W. Footrest Of 75Cm X 40Cm Finished Size Section, The Table To Be Externally Finished With 4Mm Thick Group Match Veneer Having Pattern With Grooves Including Necessary Lipping Of Burma Teak Wood, Moldings, French Polish Confirming To I.S.-2338 With Anti-Termite Treatment, Melamine Polish For Veneer And Exposed Lipping, Moldings, Anti-Termite To Plywood And Wood Work Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In Charge. 9 Providing & Fixing In Position Table Having Overall Size Of 120Cm X 60Cm X 76Cm Height Made Out Of 19Mm Thick Marine Ply Confirming To I.S.303 / I.S.710-1980 Top, Vertical Side & 6Mm Marine Plywood Confirming To I.S.303 / I.S.710-1980 Sides, Bottom With Necessary Sliders, One Open Shelf Of 19Mm Thick Marine Ply With Necessary Lipping On External Sides And Foot Rest Of 75Cm X 40Cm Finished Size Of Cptw Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In Charge. The External Side And Top Shall Be Finished With 1Mm Thick Decorative Laminate Sheet Confirming To I.S.-2046 Matt / Suede / Fine Line Finished Lamination Pattern With Grooves, All Internal Surfaces On Table And Drawer Shall Be Internally Finished With Two Coats Of French Polish Confirming To I.S.-2338 With Anti-Termite Treatment Etc. Complete. 10 Providing An Executive Chair Made In Well-Seasoned Old Burma Teak Wood With Carved Details, As Per The Architects’ Drawing, The Seat Shall Be Covered With Composite Leather And The Back Shall Be Netted In Cane, All Wooden Surfaces Shall Be Finished With French Polish Confirming To I.S.-2338, Including Spray Coating All Surfaces With Approved Anti-Termite Solution As Directed By The Engineer In Charge Etc. Complete. 11 Providing Single Circular Chair Constructed In Well-Seasoned Old Burma Teak Wood As Per The Architects’ Drawing, The Seat Shall Be Netted In Cane, All Wooden Surfaces Shall Be Finished With French Polish Confirming To I.S.-2338, Including Spray Coating All Surfaces With Approved Anti-Termite Solution As Directed By The Engineer In Charge Etc. Complete. 12 Providing Chair Having A High Back With An Adjustable Head Rest With A Synchronized Tilting Mechanism With Multiple Locking System, Acrylonitrile Butadiene Styrene - Abs For Seat, Cushioned Back With Extra Lumber Support With Fine Tuning For Depth Adjustment, With Swivel & Depth, The Chair Shall Have Adjustable Arm Pad & Option Of Pvc Padding, The Seat Shall Have A Gas Lift For Height Adjustment And A Nylon Base With Castors Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In Charge. 13 Providing Visitor Chair Having A Medium Back With Head Rest, With A Synchronized Tilting Mechanism With Multiple Locking Systems, Acrylonitrile Butadiene Styrene - Abs For Seat, With Swivel & Depth, The Chair Shall Have Adjustable Arm Pad & Option Of Pvc Padding, The Seat Shall Have A Gas Lift For Height Adjustment And A Nylon Base With Castors Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In Charge. 14 Providing Fix Chair Having The Seat And Back Made Up Of 1.2Cm Thick Hot-Pressed Plywood, Upholstered With Fabric Upholstery Covers And Molded Polyurethane Foam. The Back Foam Shall Be Designed With Contoured Lumbar Support For Extra Comfort. The Seat Shall Have Extra Thick Foam On Front Edge To Give Comfort To Popliteal Area. Back Size Shall Be 47.5Cm ( W ) X 58Cm ( H ) , Seat Size Shall Be 47Cm ( W ) X 48Cm ( D ) . The Polyurethane Foam Shall Be Molded With Density 45+ / -2 Kg / M3 And Hardness 20+ / - 2 On Hampden Machine At 25% Compression, One-Piece Armrests Shall Be Injection Molded From Black Copolymer Polypropylene Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In Charge. 15 Providing & Supplying Two-Seater Sofa Of Overall Size 1350Mm X 760Mm X 825Mm Height Made Out Of 75Mm X 38Mm Finished Size Cctw Section Frame, 6Mm Commercial Plywood Confirming To I.S.303 / I.S.710-1980 For Necessary Covering From Back & Arm Rests. The Seat Shall Be 100Mm Thick Heavy Density Foam Covered With 1 Soft Foam And Arms Having Cctw 50Mm Thick 50 Density Foam Covered With 1 Plain Soft Foam. All Work Covered With Tapestry Fabric Including Necessary Hardware, Nawar, Jute Cloth, Casement, Springs Or Belted Absorber Etc. Complete. All Exposed Wooden Surface Shall Be Melamine Polished And Anti-Termite Treatment To Plywood And Woodwork Including All Leads & Lifts Etc. Complete As Per Architects Drawing & As Per Instruction Of Engineer-In-Charge. 16 Providing And Supplying Cctw Stool Of Size 0.45M X 0.45M Of Height 0.75M Using Cctw Framework And Top Of 25Mm Thick, As Per Typical Drawing With French Polish Confirming To I.S.-2338 And Finishing Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In Charge. 17 Supplying Glass Tabletop 8Mm Thick In Required Size And Shape Including Finishing The All Side Edges Smooth Mechanically Etc. Complete As Per Architects’ Drawing And As Per Instruction Of Engineer In Charge. 18 Making And Providing And Fixing Roller Blinds Fabric Curtains For Window Using Powder Coated Rod And Mechanical System With Chain For Opening / Closing Movements Of The Blinds And Fixing Properly At Sites And At Directed By Engineer In Charge Etc. Complete. 19 Supplying Tablecloth Of Approved Make. 20 Providing And Supplying Footrest Below Table As Per Approved Typical Drawing Of 75Cm X 40Cm Size And Height Using Commercial Plywood 18Mm Thick With French Polish Confirming To I.S.-2338 And Finishing Etc. Complete. 21 Supplying And Fixing On Site Single Static Drive Type Body 2 Bay Of Compactors Of Size 1790Mm X 445Mm X 2375Mm Made Out Of 0.8Mm Thick Cold Rolled Cold Annealed Steel Conforming To Is:513 Grade, Having 5 Loading Levels ( Load Bearing Capacity - 80 Kgs Uniformly Distributed Load ) Formed By 4 Nos Of Adjustable Shelves, Finished With Fire Retardant Epoxy Polyester Powder Coating Of Approved Color & Shade With A Dry Film Thickness Of Minimum 40 Microns, Oven Baked With A Controlled Temperature Of 180 Deg. C To 200 Deg. C, The Undercarriage Made Up Of Welded Frame Of Hr Sheet 3.15Mm Thick Conforming To Is:10748 Suitably Fabricated To Take The Load Based On Configuration Having Fasteners, Label Holders, Mounted On Guide Channels As Per Approved Specifications And Design Etc. Complete. Vertical Structure To Be J Profile. Two Such J Profiles To Be Joined With Full Steel Sheet And Welded For Additional Strength. Shelf To Have Minimum 30Mm Bend. Each Shelf To Have Minimum 10 Bends. 22 Supplying And Fixing On Site Abc 6 Kg New Fire Extinguisher, Valve Pressure Gauge, Pvc Hose Pipe, Safety Pin Having Isi No 15683, Wall Bracket Etc. Complete.
