Indian Institute Of Management-IIMA has published Annual Maintenance New Academic Building , Amphitheatre , Instructional Building , Library , Administrative Building , Lake View Hostel And Dining Complex , Nf-I , Ii , Iii , B , C Quarter , Pgpex Mess , Garage Building In Iimc And 10 Flats I. Submission Date for this Tender is 23-03-2020. Building Work Tenders in IIM CALCUTTA West Bengal. Bidders can get complete Tender details and download the document.
Name of Work: Annual maintenance of New Academic Building, Amphitheatre, Instructional Building, Engineering Division Building, Main Gate, Security Offices, Post Office, IIMC Co-operative Store & Coffee Corner, Library, Administrative Building, Lake View Hostel & Dining Complex, NF-I, NF-II & NF-III Buildings and Genexx Valley. | |||||
---|---|---|---|---|---|
Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
1 | 1 | BUILDING SCHEDULE ITEMS | item 1 | ||
2 | 2 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.\n(a) Depth of excavation not exceeding 1,500 mm. | item 2 | 1 | Cu.M. |
3 | 3 | (A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) | item 3 | 1 | Cu.M. |
4 | 4 | Pumping out water from ponds or tanks | item 4 | 1 | Cu.M. |
5 | 5 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed\nwithin a lead of 75 m.\na) In all floor including roof. | item 5 | 10 | Cu.M. |
6 | 6 | Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75m.\nIn all floor including roof.\n(a) upto 150 mm. thick | item 6 | 10 | Cu.M. |
7 | 7 | (b) above 150 mm. thick | item 7 | 10 | Cu.M. |
8 | 8 | Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars.\n(a) In all floor including roof. | item 8 | 2 | Cu.M. |
9 | 9 | Dismantling terraced roof in all floor roof (including floor finish, if any.) taking out carefully tiles with beams, joists, tees or burgahs covering floor below, sorting and stacking sevicable materials at site and removing rubbish as directed within a lead of 75 m.\n(a) In all Floor including roof. | item 9 | 1 | Sq.M. |
10 | 10 | Dismantling carefully terraced floor only (including floor finish if any) or lime terracing in all floor roof and removing rubbish as directed within a lead of 75 m.\n(a) In all Floor including roof. | item 10 | 1 | Cu.M. |
11 | 11 | Dismantling artificial stone flooring upto 50 mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m.\na) In all floor including roof. | item 11 | 1 | Sq.M. |
12 | 12 | Taking out carefully Ranigunge pattern tiles from roof stacking seviceable tiles at site and removing rubbish as directed within a lead of 75m. | item 12 | 1 | Sq.M. |
13 | 13 | Taking out carefully G.C.I. or C.I. or asbestos sheets (including ridges etc.) from roof or wall after unscrewing bolts, nuts, screws etc.and stacking the material at site as directed. | item 13 | 1 | Sq.M. |
14 | 14 | Dismantling Chunar stone flooring carefully including removing rubbish to anywhere within a lead of 75 m. and stacking the serviceable\nmaterials as directed. | item 14 | 100 | Sq.M. |
15 | 15 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a\nlead of 75m as directed. | item 15 | 200 | Sq.M. |
16 | 16 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge | item 16 | 20 | Cu.M. |
17 | 17 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. | item 17 | 1 | Sq.M. |
18 | 18 | Labour for laying single brick flat soling including ramming and dressing bed to proper level and filling joints with powdered earth. | item 18 | 1 | Sq.M. |
19 | 19 | Brick-on-edge floor or pavement with 1st class brick set close in cement mortar (1:6) and laid with cushion of sand below (including cost thereof) including ruled or flush pointing with cement mortar (1:4) on top. | item 19 | 1 | Sq. M |
20 | 20 | Brick work with 1st class bricks in cement mortar (1:4)\n(a) In foundation and plinth | item 20 | 1 | Cu.M. |
21 | 21 | (b) In superstructure, all floor | item 21 | 2 | Cu.M. |
22 | 22 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in all floor. | item 22 | 2 | Sq.M. |
23 | 23 | Extra for using approved H.B netting in every third layer in 16 & 17 of subhead A above in any floor | item 23 | 1 | Sq.M. |
24 | 24 | (a) 75 mm. thick brick work with 1st class bricks set in cement, sand mortar (1:4) in all floor including H.B. netting in every alternate layers. | item 24 | 1 | Sq.M. |
25 | 25 | 250 mm th. Autoclave aerated concrete block Work with size 625 mm x 250 mm x 125 mm- Grade-I, having drying Shrinkage less than 0.05% conforming to IS: 2185 (Part-3)-1984 made up of fly ash (conforming to IS: 3812-1981, with permissible loss on ignition upto 6% ), lime , cement and laid in Cement Mortar (1:6) complete in all respect as per direction & satisfaction of Engineer -in Charge .\nIn Super Structure, all Floor. | item 25 | 1 | Cu.M. |
26 | 26 | 125 mm thick Autoclave aerated concrete block Work with size 625 mm x 250 mm x 125 mm- Grade-I,having drying Shrinkage less than 0.05% conforming to IS: 2185 ( Part-3)-1984 made up of fly ash (conforming to IS: 3812-1981, with permissible loss on ignition upto 6%), lime , cement and complete in all respect as per direction & satisfaction of Engineer -in Charge .\na) laid in Cement Mortar (1:6)\n-In Super Structure, all Floor. | item 26 | 1 | Sq.M. |
27 | 27 | b) laid in 3 mm (av) thick admixtured thin layered jointung mortar (self curing containing washed sand particles of size less than 600 micron & without any mica) conforming to ASTM C1384/ EN 1348 and capable of imparting splitting tensile strength & masonry specification conforming to ASTM C1660-09, when tested in accordance with ASTM C1006\n-In Super Structure, all Floor. | item 27 | 1 | Sq.M. |
28 | 28 | Making one set of scaffolding only for replacing glass panels, painting, uprooting plant and another repairing works of building and S&P works for external works only with 10 cm. dia bamboo as main posts at the rate of 1 metre centre to centre and 7.5 cm. dia bamboo ties @ 0.75 metre apart fitting and fixing with necessary coir, nails etc. as per direction of the Engineer-in- charge. (This item should be executed only after prior approval of the Engineer-in- charge). Firstly, one number to be paid and then labour rate for shifting up to further nineteenth (19) times @ 10% each time to be considered. If necessary further after twenty times of total use, another one number new and labour rate for shifting to be considered accordingly.\na) 3.90 metre height | item 28 | 10 | Each |
29 | 29 | b) Extra for additional 3.6 height or part thereof | item 29 | 20 | Each |
30 | 30 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in all floor as per relevant IS codes.\na) Pakur Variety | item 30 | 10 | Cu.M. |
31 | 31 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in all floor as per relevant IS codes.\na) Pakur Variety | item 31 | 2 | Cu.M. |
32 | 32 | Supplying ready mixed concrete of M 25 Grade with well graded stone chips of 20 mm nominal size containing designed quantity of cement per Cu.m of wet concrete produced in computerised batching plant under controlled condition using approved super plastisizer, designing concrete mix following\nI.S. 10262 and I.S. 456, transporting the mix with agitation in transit mixer to work site depositing the mix on a platform erected for the purpose at required levels of concreting and then placing the mix in its final location of form work compacting and curing the same complete as per specification & direction of the Engineer-in-charge including computerised batching plant transit mixer with all accessories vibrators etc. inclusive of all other incidental charges in this connection complete but excluding cost of hire charge of platform and its supporting staging which would be paid through separate item. [cement to be supplied by the Manufacturer/ supplier]\n(ii) With approved concrete pump | item 32 | 1 | Cu.M. |
33 | 33 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of all floor)\n(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. | item 33 | 1 | Sq.m |
34 | 34 | (e) Extra for staging beyond 4 m in any floor (Mode of measurement: area in plan x mean height of staging upto soffit of shuttering above initial 4 m) | item 34 | 1 | Cu.M |
35 | 35 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.\n(a) For works in foundation and upto roof of all floor/upto 4 m\nI. SAIL/ TATA/RINL | item 35 | 1 | M.T. |
36 | 36 | Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturer's specification] [Mode of measurement:The affected surface area of reinforcement shall be considered for payment] | item 36 | 1 | Sq. M |
37 | 37 | Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturer's specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface). | item 37 | 1 | Sq. M |
38 | 38 | (a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department] | item 38 | 200 | Sq. M |
39 | 39 | (b) Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. (No Departmental Cement is required) | item 39 | 100 | Sq. M |
40 | 40 | Removing corroded worn out portion of reinforcement (when the area of bar is damaged by more than 25%) by cutting and replacing the same by a new plain round bar of requisite diameter by binding with required lap / welding with old bar, including cost of reinforcement, complete in all respect including removing unserviceable materials from site as per direction of the Engineer - in - charge. Note : Payment on weight (Kg.) of new reinforcement. | item 40 | 1 | Kg |
41 | 41 | 25mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer's specification followed by two coat of polymer based paint, (1st coat after 4 to 5 days of concrete laying and 2 nd coat just before brick masonry work) as directed (cost of water proofing compound & polymer based paint to be paid separately).( Chequering not required over concrete or painted surface).\n[Note: - Waterproofing as per item 9, polymer based paint as per item 8 (a) of subhead C of Section (C). | item 41 | 1 | Sq.m |
42 | 42 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. | item 42 | 1 | Sq. M |
43 | 43 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour.\nIn all floor.\n3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement).\nUsing grey cement\n(iii) 35 mm. thick\n(Add extra @1.5% for each addl. floor upto 4th floor and @1.75% for each additional floor above 4th floor for item No.5 and 6 of subhead A). | item 43 | 1 | Sq. M |
44 | 44 | 35 mm. thick (finished) terrazo work, cast in situ in floor and 20 mm. thick (finished) in dado, skirting staircase etc. laid in panels or pattern using cement concrete (1:2:4)backing with 12 mm stone chips as directed and necessary terrazo topping with mosaic chips including rounding off corners and high polishing etc. complete as per specification laid down in I.S : 2114-1962 including raking out joints or roughening of concrete surface & application of cement slurry before flooring works using cement @ 1.75 kg./sq.m. all complete including all materials & labour.\n(Add extra @ 1.5% for each additional floor upto 4 th floor and @ 1.75 % for each addl. floor above 4 th floor)\n[White cement for item No 9 of subhead A to be supplied by the contractor including cost thereof and grey cement willbe supplied by the Dept at the isuue rate]\nIn all floor.\n(A) 9 mm. thick terazo topping, laying and finished to 6 mm. thick after final grinding with 0 to 7 mm. size mosaic chips\n(i) In ordinary grey colour | item 44 | 1 | Sq. M |
45 | 45 | (ii) In black colour | item 45 | 1 | Sq. M |
46 | 46 | (iii) In red colour | item 46 | 1 | Sq. M |
47 | 47 | (iv) In silver grey (ordinary cement and white cement to be used in equal proportion in topping) | item 47 | 1 | Sq. M |
48 | 48 | (v) In pink, green, yellow, light green colour using white cemeny only and necessary pigment. | item 48 | 1 | Sq. M |
49 | 49 | Supplying dividing strip fitted and fixed with cement mortar\n(1:3) in mosaic or patent stone floor, dado etc. complete as per direction of the Engineer-in-charge.\n(i) Glass - 3mm. Thick\n(a) 20 mm. wide strip | item 49 | 1 | Mtr. |
50 | 50 | (b) 25 mm. wide strip | item 50 | 1 | Mtr. |
51 | 51 | (c) 37 mm. wide strip | item 51 | 1 | Mtr. |
52 | 52 | (ii) Aluminium - 25 mm. wide & 2mm. thick. | item 52 | 1 | Mtr. |
53 | 53 | Supplying, fitting and fixing Black Stone slab used in Kitchen slab, alcove, wardrobe etc. laid and jointed with necessary adhesive Cement mortar (1:2) including grinding or polishing as per direction of Engineer-in -Charge in all Floor.\n(a) Slab Thickness 20 to 25 mm\n(Add extra for each addl, floor over the rate for item 22, 25, 26, 17, 20, 31, 32 & 15 of subhead A.\n(I) upto 4 th floor- Rs. 12/-per Sq.m\nII) above 4th floor -Rs. 16/- per Sq.m | item 53 | 400 | Sq. M |
54 | 54 | 18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0 kg/Sq.m] | item 54 | 1 | Sq. M |
55 | 55 | Extra cost of labour for prefinished and premoulded Nosing to treads of steps, railing, window sill etc. of Kota Stone. | item 55 | 1 | M |
56 | 56 | Extra cost of labour for grinding Kota Stone Floor in treads and riser of Steps. | item 56 | 1 | Sq. M |
57 | 57 | Supplying, fitting and fixing 18 mm. to 22 mm. thick kota stone slab in wall, dado in 15 mm thick [avg] cement mortar (1:3) including making suitable arrangement to hold the stone properly by brass / copper hooks including pointing in cement mortar (1:2) (1 cement : 2 marble dust) with admixture of pigments matching the stone shade, including grinding and polishing all complete as per direction of Engineer-in-charge including cost of materials, labour, scaffolding, staging, curing complete.\n[Using cement slurry for bedding @4.4 kg/Sq.m and for jointing @1.8 kg/Sq.m] | item 57 | 1 | Sq. M |
58 | 58 | Grinding to marble / mosaic floor including remaining stone, if necessary, after cutting with manual labour / machine,\nwhere necessary | item 58 | 100 | Sq. M |
59 | 59 | Supplying, fitting and fixing Marble Slab/tile of 15 to 18 mm thickness in floor, lobby, stair, landing & treads etc. over 20 mm (av.) thck base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointed with white cement slurry @ 2.0 kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineering -in -Charge in all Floor. {White cement and Pigment to be supplied by the Agency]\n(a) With Makrana plain pink / Adranga Pink / Garbh Gulabi\n/ Udaypur pink / Udaypur Green / Black Bhaslana\n(i) Area of each Slab/tile upto 0.3 sq.m | item 59 | 1 | Sq. M |
60 | 60 | (ii) Area of each Slab/tile exceeding 0.3 sq.m. but not\nexceeding 0.6 sq.m. | item 60 | 1 | Sq. M |
61 | 61 | (iii) Area of each Slab/tile exceeding 0.60 sq.m but not exceeding 1.00 sq.m. | item 61 | 1 | Sq. M |
62 | 62 | (iv) Area of each slab/tile exceeding 1.00 sq.m (This item to be executed on specific permission of Superintending Engineer) | item 62 | 1 | Sq. M |
63 | 63 | (b) With Chawk Dungri\n(i) Area of each tile upto 0.3 sq.m. | item 63 | 1 | Sq. M |
64 | 64 | (ii) Area of each tile exceeding 0.3sq.m. but not exceeding 0.6\nsq.m. | item 64 | 1 | Sq. M |
65 | 65 | (iii) Area of each tile exceeding 0.6 sq.m but not excedding 1\nsq.m. | item 65 | 1 | Sq. M |
66 | 66 | (iv) Area of each slab/tile exceeding 1.00 sq.m (This item to be executed on Specific permission of Superintending Engineer) | item 66 | 1 | Sq. M |
67 | 67 | Extra cost of labour for prefinished and premoulded Nosing to treads of steps, railing, window sill etc. of Marble Stone. | item 67 | 1 | Meter |
68 | 68 | Extra cost of labour for Marble Stone Floor in treads of Steps. | item 68 | 1 | Sq. M |
69 | 69 | Supplying, fitting & fixing granite tiles 10mm to 12mm. thick in columns, wall, facia etc. with 15 thick [avg] cement mortar (1:2) including making suitable arrangements to hold the stones properly by brass / copper hooks including pointing in cement mortar (1:2) (1 white cement : 2 marble dust) with admixture of pigment matching the stone shades all complete as per direction of the Engineer-in-charge including cost of all materials, labours, scaffolding, staging ,curing and roughening of concrete surface complete.\n[Using cement slurry at back side of tiles@ 4.4 kg/sq.m & white cement slurry for joint filling @ 1.8 kg/sq.m]\nArea of each slab upto 0.2 Sq.m | item 69 | 1 | Sq. M |
70 | 70 | Supplying, fitting & fixing granite slabs 15mm to 18 mm. thick with uniform texture & without decorative veins in columns, wall, facia etc. with 15 mm thick [avg] cement mortar (1:2) including making suitable arrangements to hold the stones properly by brass / copper hooks including pointing in cement mortar (1:2) (1 white cement : 2 marble dust) with admixture of pigment matching the stone shades all complete as per direction of the Engineer-in-charge including cost of all materials, labours, scaffolding, staging ,curing and roughening of concrete surface complete. Area of each Granite slab > 0.6 upto 1.0 square metre.\n[Using cement slurry at back side of granite @ 4.4 kg/sq.m & white cement slurry for joint filling @ 1.8 kg/sq.m] | item 70 | 70 | Sq. M |
71 | 71 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.\n(A) Floor\nWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @\n0.20kg/Sq.m.\n(a) Area of each tile upto 0.09 Sq.m\n(i) Coloured decorative\n | item 71 | 100 | Sq. M |
72 | 72 | (ii) Other than Coloured decorative including white | item 72 | 1 | Sq. M |
73 | 73 | (b) Area of each tile above 0.09 Sq.m\n(i) Coloured decorative | item 73 | 50 | Sq. M |
74 | 74 | (ii) Other than Coloured decorative including white | item 74 | 1 | Sq. M |
75 | 75 | (B) Wall\nWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.\n(a) Area of each tile upto 0.09 Sq.m\n(i) Coloured decorative | item 75 | 100 | Sq. M |
76 | 76 | (ii) Other than Coloured decorative including white | item 76 | 1 | Sq. M |
77 | 77 | (b) Area of each tile above 0.09 Sq.m\n(i) Coloured decorative | item 77 | 50 | Sq. M |
78 | 78 | (ii) Other than Coloured decorative including white | item 78 | 1 | Sq. M |
79 | 79 | (C) Floor\nWith Polymerised Adhesive and Epoxy grout pointing including spacer- 2 mm ( When Tiles are laid over existing hard ready surface)\n(a) Area of each tile upto 0.09 Sq.m [using adhesive 3 mm\nthick]\n(i) Coloured decorative | item 79 | 1 | Sq. M |
80 | 80 | (ii) Other than Coloured decorative including white | item 80 | 1 | Sq. M |
81 | 81 | (b) Area of each tile above 0.09 Sq.m [using adhesive 4.5 mm thick]\n(i) Coloured decorative | item 81 | 1 | Sq. M |
82 | 82 | (ii) Other than Coloured decorative including white | item 82 | 1 | Sq. M |
83 | 83 | (D) Wall\nWith Polymerised Adhesive and Epoxy grout pointing including spacer- 2 mm ( When Tiles are laid over existing hard ready surface)\n(a) Area of each tile upto 0.09 Sq.m [using adhesive 3 mm\nthick]\n(i) Coloured decorative | item 83 | 1 | Sq. M |
84 | 84 | (ii) Other than Coloured decorative including white | item 84 | 1 | Sq. M |
85 | 85 | (b) Area of each tile above 0.09 Sq.m [using adhesive 4.5 mm\nthick]\n(i) Coloured decorative | item 85 | 1 | Sq. M |
86 | 86 | (ii) other than Coloured decorative including white | item 86 | 1 | Sq. M |
87 | 87 | Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor\n(I) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment.\n(A) Deep Colour & White | item 87 | 50 | Sq. M |
88 | 88 | (B) Light Colour | item 88 | 1 | Sq. M |
89 | 89 | (II) With Polymerised Adhesive [6 mm thick] & epoxy grouting materials for filling joints including spacer-2 mm [Applied directly over finished artificial stone floor/ mosaic etc.]\n(A) Deep Colour & White | item 89 | 1 | Sq. M |
90 | 90 | (B) Light Colour | item 90 | 1 | Sq. M |
91 | 91 | Supplying, fitting & fixing best quality digital printed Ceramic tiles in coloured decorative on walls and floors to match with the existing work & 4 nos. key stones (10mm) fixed with adhesive 4.5 mm thick at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. With polymerised adhesive and epoxy grout pointing including spacer - 2mm (When tiles are laid over existing hard ready surface) all complete as per direction of Engineer-in-charge. | item 91 | 10 | Sqm. |
92 | 92 | Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brand conforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.)\n= 0.08 %] in floor, skirting etc. using polymerised adhesive of 6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course and joints grouted with admixture of white epoxy grout materials of approved brand including spacer -2mm as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete as per direction of Engineer- in-Charge. (Note: This work should not be executed without specific permission of Superintending Engineer)\n(a) ln all FIoor:(size not Iess than 600mmX 600 mm X 9.5\nmm thick) | item 92 | 10 | sqm. |
93 | 93 | Supplying and laying chequered tiles of any shade & of approved quality with (1:1½:3) cement concrete laid in panels or patterns as directed in pavement, footpath etc. including necessary underlay 25 mm thick [avg] cement mortar (1:3) complete in all respect with all labour and materials. [Using cement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.m for joint filling]\nRed Variety\n(i) 25 mm. thick | item 93 | 10 | Sq. M |
94 | 94 | (ii) 30 mm. thick | item 94 | 1 | Sq. M |
95 | 95 | Supplying& laying 20 mm designer chequered tiles of any shade and of approved quality as per IS: 1237: 1980 laid in patterns as directed in pavement, footpath including necessary underlay 25 mm thick average cement mortar (1:3) complete in all respect with all labour and materials [using cement slurry @ 4.4 kg/Sq.m at back side of tiles. | item 95 | 50 | Sq. M |
96 | 96 | Supplying & laying as per IRC-SP:063-2004 paver unit of any shade of approved quality as per relevant IS code, laid in pattern as directed in pavement, footpath, driveway (paver block only), etc including necessary underlay complete in all respect with all labour and material.\n[Border concrete if necessary to be paid separately].\nNote: Sub-grade CBR should not be less than 5.\na) 25 mm thick Tiles as per IS: 1237-2012 for footpath,ramp,staircase of public building(over 25 mm thick (Avg) Cement mortar (1:3) & Cement Slurry @ 4.4 kg/Sq.m at back side of Block. \n(i) Grey | item 96 | 1 | Sq. M |
97 | 97 | (ii) Coloured Decorative | item 97 | 1 | Sq. M |
98 | 98 | (b) 50 mm thick interlocking designer concrete paver block M-\n30 grade for non-traffic zone,buiding premises,garden,parks,domestic drive as per IS: 15658- 2006(over 20-30 mm medium sand bed on 200mm thk bound gnaular /granular base course including cost of sand for sand bed but excluding cost of base course & subgrade preparation.)\n(i) Grey | item 98 | 1 | Sq. M |
99 | 99 | (ii) Coloured Decorative | item 99 | 1 | Sq. M |
100 | 100 | A) Supplying & laying of approved brand of scratch proof, semi flexible P.V.C. blended homogeneous marble Vinyle flooring in tiles conforming to IS:3461, fixing with synthetic acrylic adhesive after preparing the floor, levelling & smothaning when necessary with suitable putty, as per the design & instruction of the Engineer-in-charge.\n2 mm thick | item 100 | 1 | Sq. M |
101 | 101 | B) Supplying & laying of approved make and brand of scratch proof, flexible & homogeneous P.V.C. Vinyle flooring conforming to IS:3462 - 1982 in required finish, fixed with synthetic acrylic adhesive after preparing the floor, levelling & smothaning when necessary with suitable putty, as per the design & instruction of the Engineer-in-charge.\n(i) 2 mm thick (Plain) | item 101 | 1 | Sq.M |
102 | 102 | (ii) 1.5 mm thick (with stud / checkered) | item 102 | 1 | Sq.M |
103 | 103 | Filling rat-holes with broken glass and cement concrete (1:3:6) with jhama chips including shaping holes and mending\ndamages. | item 103 | 10 | each |
104 | 104 | Washing and cleaning with oxalic acid powder using 33 gms./sq.m.\n(a) Marble floor/ marble dado | item 104 | 100 | Sq.M |
105 | 105 | (b) Floor/ dado other than marble | item 105 | 100 | Sq.M |
106 | 106 | Polishing only of old marble or terrazo work with oxalic acid powder using 33 gms/ sq.m. by manual labour / machine where necessary. | item 106 | 1 | Sq. M |
107 | 107 | Taking out Mirzapur or glazed porcelain tiles carefully by chiselling from walls or floor including stacking serviceable material as directed. | item 107 | 100 | Sq.M |
108 | 108 | Washing and cleaning with soap water and rubbing with oil cloth in all types of floor and dado. | item 108 | 100 | Sq.M |
109 | 109 | Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor)\n(i) In Roof:-\na) With 0.60 mm thick sheet | item 109 | 1 | Sq.M |
110 | 110 | b) With 0.63 mm thick sheet | item 110 | 1 | Sq.M |
111 | 111 | c) With 0.80 mm thick sheet | item 111 | 1 | Sq.M |
112 | 112 | Galvanised iron sheet ridging fitted with necessary bolts, screws, washers etc complete.(225mm end lapping)\n(A) 300 mm lapping each way\n(a) With 0.60 mm sheet | item 112 | 1 | Metre |
113 | 113 | (b) With 0.63 mm sheet | item 113 | 1 | Metre |
114 | 114 | (c) With 0.80 mm sheet | item 114 | 1 | Metre |
115 | 115 | Galvanised iron sheet eaves gutter fitted and fixed with necessary 50 mm X 6 mm M.S flat bar clamps bent to design, bolts, nuts, washers etc. complete. Eaves gutter made of 0.63 mm. sheets.(300mm End lapping)\n(a) 225 mm. wide gutter | item 115 | 1 | Metre |
116 | 116 | (b) 300 mm. wide gutter | item 116 | 1 | Metre |
117 | 117 | Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work).\n(i) In Roof:-\na) With 0.5 mm thick sheet | item 117 | 350 | Sq.M. |
118 | 118 | Aluminium sheet ridging fitted with self tapping screws, EPDM washers etc complete.(Minimum 225mm end lapping).\n(A) 300 mm lapping each way\n(a) With 0.71 mm sheet | item 118 | 10 | Mtr. |
119 | 119 | (b) With 0.91 mm sheet | item 119 | 1 | Mtr. |
120 | 120 | Supplying, fitting and fixing glass reinforced polyester translucent fiber glass sheet to match with GCI Corrugation as per IS: 12866 - 1989 in roof fitted and fixed with 10 mm dia "J" or "L" hook, bolts and nuts, limpet and bitumen washers and putty with 150mm end lap and one corrugation minimum side lap complete.\na) 1.6mm +/- 0.2 mm thick sheet.(2.6Kg/Sq.m)\ni) Natural white or tinted blue colour | item 120 | 1 | Sq.M |
121 | 121 | ii) Fire retardant milky white | item 121 | 1 | Sq.M |
122 | 122 | iii) Coloured other than natural white or tinted blue | item 122 | 1 | Sq.M |
123 | 123 | iv) Special coloured textured tissue | item 123 | 1 | Sq.M |
124 | 124 | Supplying and laying standard four course bituminous water proofing treatment as per specification laid down in I.S. 1346\n- 1991 to be finished with pea size gravel including necessary preparatory works such as shaping mouth of outlets, cutting as and where necessary and refilling with sand and Cement mortar (4:1) or Cement Concrete (1:2:4) with graded stone chips before undertaking the treatment including cutting grooves in parapet and inserting edge of felt and mending good damage complete in all respect as per direction of Engineer - in - Charge including cost of all materials and labours and incidental charges but excluding the cost of Cement Mortar or concrete required for levelling and grading. (In sloped roof Course sand of approved varieties is to be used in place of Pea size gravels as fourth and final course.)\ni) 1st and 3rd Course with bonding materials of hot applied industrial blown type bitumen of grade 85/25 or 90/15 conforming to I.S.702 - 1988 @ 12Kg/10Sqm on each layer.\nA. Over Flat Roof. | item 124 | 1 | Sq.M. |
125 | 125 | Supplying & laying 3mm thick pre-fabricated plastomeric water proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene (APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusible polyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturer's specification on smooth,clean dry surface prepared wherever required.Lap joint shall be provided of 75 mm in longitudinal & 100 mm in transverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, complete removal of entrapped air and sealing edges into grooves in appropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicable taxes. (Payment shall be made on the basis of finished surface area.).\nMembrane Property: Softening Point > 150 deg C, Cold Flexibility < -6 deg C, Tensile Strength, N/cm : 600 (longitudinal), 450 (transverse), Tearing Strength, N: 300 (longitudinal), 200 (transverse) | item 125 | 660 | Sqm. |
126 | 126 | Taking out old damaged tarfelt from the roof, parapet etc. preparing the roof surfaces by removing all spoils, blisters, moss etc. from the working site and disposal of the same beyond the compound and cleaning the site in all respect as per direction of Engineer-in-Charge. | item 126 | 500 | Sq.M. |
127 | 127 | Repairs to cracks in terraced roof by cutting V-grooves 75 mm. to 100 mm. deep and 150 mm. to 200 mm. wide and filling the same with beaten lime concrete (2:2:7) with lime putty / paste and finishing complete (2 lime putty / paste : 2 surki : 7 brick khoa ) | item 127 | 70 | Metre |
128 | 128 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-in- charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc.\nPayment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the all. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof.\nI) For structural members of specified sections weighing less than\n22.5 Kg./m | item 128 | 0.25 | MT |
129 | 129 | II) For Structural Works in Roof Trusses etc. using joists, channels and angles of specified section weighing less than 22.5 kg/ m | item 129 | 0.25 | MT |
130 | 130 | III) For built up sections / srtuctural members of specified sections weighing not less than 22.5 Kg./m | item 130 | 0.25 | MT |
131 | 131 | M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete.\nThe rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete.\nPayment to be made on the basis of calculated weight of structural memebrs of MS Holow Section as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a hight of erection 8 m. / 2nd floor level from the all. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof.\ni) For roof truss works\na) Span up to 12 Mtr | item 131 | 0.25 | MT. |
132 | 132 | b) Span beyond 12 Mtr and up to 20.00 Mtr | item 132 | 0.25 | MT. |
133 | 133 | c) Span beyond 20 Mtr and up to 30 Mtr | item 133 | 0.25 | MT. |
134 | 134 | Labour for hoisting and placing in proper position (up to 1st floor level) departmental R.S. joists, channels, angles. Tees, plates etc. including fitting and fixing same with bolts and nuts, if necessary (but excluding cost of such bolts and nuts) | item 134 | 1 | Qntl. |
135 | 135 | (a) Add extra for each additional floor over 1st floor. | item 135 | 1 | Qntl. |
136 | 136 | M.S. works in framed gratings of window etc.made of round or square bars and frame work or M.S. flats (with the bars securely fixed to the flat bar frame) with or without intermediate flat bar stiffener and fixed with necessary screws etc. complete, as directed.\nIn all floor. | item 136 | 1 | Qntl. |
137 | 137 | (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in all\nfloor.\n(Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25% for each addl. floor above 4th floor)\n(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. | item 137 | 10 | Qntl |
138 | 138 | (ii) Grill weighing above 16 Kg./sq.mtr and above | item 138 | 1 | Qntl |
139 | 139 | Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete.\nIn all floor. | item 139 | 10 | Sq.m. |
140 | 140 | (a) Supplying, fitting and fixing steel rolling shutter profile type with 18 B.G . of approved type steel latche section 75mm wide, fitted with coil wire spring to necessiate the fitting of required Nos. of C.I. Pulleys on heavy type solid drawn seamless steel tube complete with locking arrangements both inside and outside specially builtup side guide channels including providing a hood for the steel rolling shutter in the room, painting two coats of approved aluminium paint over a coat of red lead primer complete. | item 140 | 10 | Sq.m. |
141 | 141 | Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing.\nWithout integrated grills.\n(a) Fixed type steel windows as per IS sizes with horizontal glazing bars. | item 141 | 10 | Sq. M. |
142 | 142 | (b) Openable steel windows as per IS sizes with side hung shutters and horizotal glazing bars. [The extra rate admissible for the openable portion only] | item 142 | 10 | Sq,. M. |
143 | 143 | (c ) Extra over item no. 33 (a) and (b) for,\n(i) Fixed type ventilators as per I.S. sizes with horizontal glazing bars height being limited to 580 mm. | item 143 | 10 | Sq,. M. |
144 | 144 | (ii) Top hung side hung ventilators as per I.S. sizes 580 mm. | item 144 | 1 | Sq,. M. |
145 | 145 | (iii) Centre hung ventilators as per I.S. sizes 580 mm. | item 145 | 1 | Sq,. M. |
146 | 146 | (iv) Two point nose steel handle including fitting and fixing. | item 146 | 20 | Each |
147 | 147 | (v) Two point nose aluminium handle including fitting and fixing. | item 147 | 1 | Each |
148 | 148 | (vi) steel peg stay 300 mm long including fitting and fixing. | item 148 | 20 | Each |
149 | 149 | (vii) Aluminium peg stay 300 mm long including fitting and fixing. | item 149 | 1 | Each |
150 | 150 | (viii) M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continuously welded with M.S. flats and bars. | item 150 | 25 | Kg. |
151 | 151 | Welding in M.S. structural work with gas or electric:\n(a) Tack weld | item 151 | 30 | point |
152 | 152 | (b) Continuous weld. | item 152 | 30 | cm run |
153 | 153 | Renewing bottom rail or top runners of collapsible gate including mending good all damages. | item 153 | 30 | Kg. |
154 | 154 | Taking out heavy iron grated door or window (jail pattern or existing) with locking arrangement after cutting out from walls and refixing the same including mending all damages.[Mending charges to be paid separately] | item 154 | 20 | Sq.M. |
155 | 155 | Reparing collapsible gate by cutting out all rivets as necessary re- assambling all members including welding pieces of channels, sraightening bent bars and rivetting with new rivets and fitting in position and painting two coats. | item 155 | 10 | Sq.M. |
156 | 156 | Easing and oiling, cleaning collapsible gate and repairing to locking arrangements. | item 156 | 10 | Sq.M. |
157 | 157 | Easing and oiling, cleaning rolling shutters excluding repair to inside locks. | item 157 | 10 | Sq.M. |
158 | 158 | Renewing steel plated or oxidised casement stay or peg stay of steel window frames including painting two coats with approved paint complete. | item 158 | 1 | Each |
159 | 159 | Renewing hinge of steel shutter including taking out old one by cutting and fixing new hinges by welding and mending good damages complete. | item 159 | 20 | Each |
160 | 160 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).\n(d) Sal : Local. | item 160 | 1 | Cu.M |
161 | 161 | (e) Sal : Malayasian | item 161 | 0.5 | Cu.M |
162 | 162 | (f) Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak. | item 162 | 0.1 | Cu.M |
163 | 163 | (g) Kappoor | item 163 | 0.1 | Cu.M |
164 | 164 | (h) Neem, Jam, Jackfruits | item 164 | 0.1 | Cu.M |
165 | 165 | (i) Other Local Wood. | item 165 | 0.1 | Cu.M |
166 | 166 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long\nM.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer?s specification and direction of Engineer-in-Charge. | item 166 | 15 | Mtr. |
167 | 167 | B. DOOR WINDOW SHUTTER\nPanel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.\nIn all floor.\n(In case of non-supply of single plank, penal rate of reduction of 20% will be made)\n(iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm.\n(a) Ordinary Teak Wood. | item 167 | 1 | Sq.M |
168 | 168 | (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. | item 168 | 1 | Sq.M |
169 | 169 | (c) Other Local Wood. | item 169 | 1 | Sq.M |
170 | 170 | (iv) 25mm thick shutters with 12mm thick panel of size 30 to 45 cm.\n(a) Ordinary Teak Wood. | item 170 | 1 | Sq.M |
171 | 171 | (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. | item 171 | 1 | Sq.M |
172 | 172 | (c) Other Local Wood. | item 172 | 1 | Sq.M |
173 | 173 | Fixed louver shutters of doors and windows as per design, including fitting & fixing same in position but excluding the cost of hinges and other fittings in all floor.\n(ii) 40mm thick shutters with 12mm thick valve.\n(b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. | item 173 | 1 | Sq.M |
174 | 174 | Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in all floor.\n(a) 35 mm thick shutters (single leaf) | item 174 | 1 | Sq.M. |
175 | 175 | (b) 32 mm thick shutters (single leaf) | item 175 | 60 | Sq.M. |
176 | 176 | (a) Vision aperture (round or retangular in shape) with 7.4kg. Per sq.m./ 3mm thick glass pane with wooden beads. (Cost of glass panes and wooden beads will be paid separately). | item 176 | 5 | Each |
177 | 177 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge. | item 177 | 5 | Sq.m |
178 | 178 | Providing & fixing factory made 30 mm thick factory made solid pvc door shutter made out of single piece extruded solid pvc profile . The style & rails shall be of size of 75 x 30 mm having wall thickness of 5 mm. The style and top bottom rail shall have one side a thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. 15 mm thickness shall be of single piece extruded solid pvc profile whereas it shall be not be made of sheet pasted profile) . The styles and rails shall be reinforced with MS tube of size 18 mm(±) 1mm x 18 mm (±) 1mm x 1mm painted with primer all four corners of reinforcement to be welded or sealed . solid pvc extruded bidding (push fit type) will be set inside the styles and rails with a cavity to receive single piece extruded 5 mm pvc sheet as panel. The styles and rails will be metered cut and join with the help of pvc solvent cement, self tapping screw and braket of size 200 x 75 mm / welded at each corner. Single piece extruded solid pvc lockrail of size 100 x 30 mm with a wall thickness 5 mm & 15 mm integrally extruded in the middle of lockrail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8mm complete as per manufacturers specifications and direction of Engineer-in-Charge.\na) Factory made Single piece non decorative extruded PVC profiles door shutter(mat / plain finish) | item 178 | 5 | Sqm. |
179 | 179 | Supplying, Fitting & Fixing 30 mm thick Factory made moulded Door shutter, consisting of solid core single leaf flash door of 30 mm thickness lipped with 15 mm [5mmx3] thick x 30 mm wide on one style and top rail and 10 mm [5mmx2] thick x 30 mm wide of the other style and bottom rail. The inner panel laminated with 2 mm thick termite proof water proof and fire resistant moulded PVC sheet with raised panel designed in different plain/ or Prelam colour on one side after routing the moulded design on flash door and 2mm plain and or Prelam PVC sheet on other side using rubber adhesive on flash door and solvent cement adhesive on the PVC lipping etc. complete excluding hardwares as necessary as per direction of Engineer-in Charge, Manufacturer?s Specification and drawing.. In all floor.\n(b) Moulded door using 2 mm Prelam moulded PVC sheet on both side. | item 179 | 1 | Sq..M |
180 | 180 | Wood work in upper rails of railing, hand rail of staircase, balcony etc. includig necessary bend, moulding fitted and fixed complete (for purpose of payment section will be measured in the square).\n(a) 1st class best Indian teak. | item 180 | 0.1 | Cu.M |
181 | 181 | (b) Ordinary teak. | item 181 | 0.5 | Cu.M |
182 | 182 | (c) Sishu, Gamar, Champ, Badam, Bhola, Morga, Hallak. | item 182 | 0.2 | Cu.M |
183 | 183 | (d) Other Local Wood. | item 183 | 0.5 | Cu.M |
184 | 184 | Supplying, fitting, Fixing Fly / Mosquito proof nylon net on any type of window, door shutter frame with necessary fixing arrangements complete. | item 184 | 15 | Sq.M. |
185 | 185 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)\n(a) 40mm X 6mm, 250mm Length | item 185 | 1 | Each |
186 | 186 | (b) 40mm X 6mm, 200mm Length | item 186 | 1 | Each |
187 | 187 | (c) 40mm X 6mm, 125mm Length | item 187 | 1 | Each |
188 | 188 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.\n(i) 50mm. X 37mm. X 1.50mm. | item 188 | 1 | Each |
189 | 189 | (ii) 50mm. X 40mm. X 2.5mm. | item 189 | 1 | Each |
190 | 190 | (iii) 75mm. X 40mm. X 1.12mm. | item 190 | 1 | Each |
191 | 191 | (iv) 75mm. X 47mm. X 1.70mm. | item 191 | 1 | Each |
192 | 192 | (v) 75mm. X 60mm. X 3.15mm. | item 192 | 1 | Each |
193 | 193 | (vi) 100mm. X 50mm. X 1.25mm. | item 193 | 1 | Each |
194 | 194 | (vii) 100mm. X 58mm. X 1.90mm. | item 194 | 30 | Each |
195 | 195 | (viii) 100mm. X 75mm. X 3.50mm. | item 195 | 1 | Each |
196 | 196 | i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.\n(a) 200mm long | item 196 | 1 | Each |
197 | 197 | (b) 250mm long. | item 197 | 20 | Each |
198 | 198 | (c) 300mm long. | item 198 | 1 | Each |
199 | 199 | ii) Brass hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.(a) 200mm long | item 199 | 1 | Each |
200 | 200 | (b) 250mm long. | item 200 | 1 | Each |
201 | 201 | (c) 300mm long. | item 201 | 1 | Each |
202 | 202 | (a) Supplying 'Godrej' mortice lock chromium plated with latch and keys 4 levers, including fitting and fixing complete. | item 202 | 1 | Each |
203 | 203 | (b) Supplying 'Godrej' mortice lock chromium plated with keys 6 levers including fitting & fixing complete. | item 203 | 10 | Each |
204 | 204 | (c) Supplying 6 levers 'Godrej' Crystal Satine Mortice Lock with keys including fitting & fixing complete. | item 204 | 1 | Each |
205 | 205 | i) Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete.\n(a) Heavy type (I.S.I. size 3) | item 205 | 1 | Each |
206 | 206 | (b) Medium (I.S.I. size 2) | item 206 | 1 | Each |
207 | 207 | (c) Light (I.S.I. size 4) | item 207 | 1 | Each |
208 | 208 | ii) Godrej Hydraulic door closer fitted and fixed complete.\n(a) Heavy type | item 208 | 10 | Each |
209 | 209 | (b) Medium type | item 209 | 25 | Each |
210 | 210 | (c) Light type | item 210 | 1 | Each |
211 | 211 | (A) Iron door ring of approved quality fitted and fixed with nut and washer complete.\n(i) 50mm dia. | item 211 | 50 | Each |
212 | 212 | (ii) 75mm dia. | item 212 | 1 | Each |
213 | 213 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:\n(i) 50mm long x 10mm dia. bolt. | item 213 | 1 | Each |
214 | 214 | (ii) 75mm long x 10mm dia. bolt. | item 214 | 1 | Each |
215 | 215 | (iii) 100mm long x 10mm dia. bolt. | item 215 | 20 | Each |
216 | 216 | (iv) 150mm long x 10mm dia. bolt. | item 216 | 30 | Each |
217 | 217 | (v) 150mm long x 12mm dia. bolt. | item 217 | 1 | Each |
218 | 218 | (vi) 200mm long x 10mm dia. bolt. | item 218 | 10 | Each |
219 | 219 | (vii) 225mm long x 10mm dia. bolt. | item 219 | 1 | Each |
220 | 220 | (viii) 225mm long x 12mm dia. bolt. | item 220 | 1 | Each |
221 | 221 | (ix) 300mm long x 10mm dia. bolt. | item 221 | 1 | Each |
222 | 222 | (x) 300mm long x 12mm dia. bolt. | item 222 | 1 | Each |
223 | 223 | Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete.\n(i) 250mm x 16mm dia bolt. | item 223 | 1 | Each |
224 | 224 | (ii) 250mm x 19mm dia. bolt. | item 224 | 1 | Each |
225 | 225 | (iii) 300mm x 16mm dia. bolt. | item 225 | 1 | Each |
226 | 226 | (iv) 300mm x 19mm dia. bolt. | item 226 | 1 | Each |
227 | 227 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:\n(a) With continuous plate base (Hexagonal/ Round rod)\n(i) 75 mm grip x 10 mm dia rod. | item 227 | 1 | Each |
228 | 228 | (ii) 100 mm grip x 10 mm dia rod. | item 228 | 1 | Each |
229 | 229 | (iii) 100 mm grip x 12 mm dia rod. | item 229 | 1 | Each |
230 | 230 | (iv) 125 mm grip x 10 mm dia rod. | item 230 | 20 | Each |
231 | 231 | (v) 125 mm grip x 12 mm dia rod. | item 231 | 1 | Each |
232 | 232 | (vi) 150 mm grip x 10 mm dia rod. | item 232 | 1 | Each |
233 | 233 | (vii) 150 mm grip x 12 mm dia rod. | item 233 | 1 | Each |
234 | 234 | (b) With round base:\n(i) 75 mm grip x 10 mm dia rod. | item 234 | 1 | Each |
235 | 235 | (ii) 100 mm grip x 10 mm dia rod. | item 235 | 1 | Each |
236 | 236 | (iii) 100 mm grip x 12 mm dia rod. | item 236 | 1 | Each |
237 | 237 | (iv) 150 mm grip x 10 mm dia rod. | item 237 | 1 | Each |
238 | 238 | (v) 150 mm grip x 12 mm dia rod. | item 238 | 1 | Each |
239 | 239 | (a) Metallic magic eye of approved quality fitted and fixed complete. | item 239 | 15 | Each |
240 | 240 | Supplying , fitting and fixing Godrej ultra vertibold brass rim lock. | item 240 | 4 | Each |
241 | 241 | (a) Supplying, fitting fixing I.S.I. approved quality and brand hydraulic (oil check) floor door spring, heavy duty double action with brass shoe, brass top centre aluminium top cover etc. complete set as per direction of Engineer-in- charge. | item 241 | 10 | Set |
242 | 242 | (b) Supplying, fitting fixing Godrej type hydraulic (oil check) floor door spring, heavy duty double action with brass shoe, brass top centre aluminium top cover etc. complete set as per direction of Engineer-in-charge. | item 242 | 1 | Set |
243 | 243 | Supplying, fitting and fixing Godrej Multi Lock or equivallent . | item 243 | 10 | Each |
244 | 244 | Taking out old iron higes and fitting, fixing the same with new steel screws.\n(a) 50mm. Long butt hinge. | item 244 | 1 | Each |
245 | 245 | (b) 65mm. Long butt hinge. | item 245 | 1 | Each |
246 | 246 | (c) 75mm. Long butt hinge. | item 246 | 1 | Each |
247 | 247 | (d) 90mm. Long butt hinge. | item 247 | 1 | Each |
248 | 248 | (e) 100mm. Long butt hinge. | item 248 | 30 | Each |
249 | 249 | (f) 125mm. Long butt hinge. | item 249 | 1 | Each |
250 | 250 | (g) 150mm. Long butt hinge. | item 250 | 1 | Each |
251 | 251 | (h) 50mm. Long parliamentary hinge. | item 251 | 1 | Each |
252 | 252 | (i) 65mm. Long parliamentary hinge. | item 252 | 1 | Each |
253 | 253 | (j) 75mm. Long parliamentary hinge. | item 253 | 1 | Each |
254 | 254 | (k) 100mm. Long parliamentary hinge. | item 254 | 1 | Each |
255 | 255 | (l) 125mm. Long parliamentary hinge. | item 255 | 1 | Each |
256 | 256 | (m) 150mm. Long parliamentary hinge. | item 256 | 1 | Each |
257 | 257 | (n) 175mm. Long parliamentary hinge. | item 257 | 1 | Each |
258 | 258 | (o) 200mm. Long parliamentary hinge. | item 258 | 1 | Each |
259 | 259 | Renewing iron mortice lock (local best approved quality) 6 lever with handle, connected rods and keys consisting a complete set:\n(a) With chromium plated handle. | item 259 | 10 | Each |
260 | 260 | (b) With oxidised handle. | item 260 | 1 | Each |
261 | 261 | (c) With anodised aluminium white handle. | item 261 | 1 | Each |
262 | 262 | (d) With anodised aluminium decorative handle. | item 262 | 1 | Each |
263 | 263 | Renewing mortice lock handle with connected rod:\n(a) With chromium plated. | item 263 | 10 | Pair |
264 | 264 | (b) Oxidised. | item 264 | 1 | Pair |
265 | 265 | (c) Anodised aluminium (white). | item 265 | 1 | Pair |
266 | 266 | (d) Anodised aluminium (decorative). | item 266 | 1 | Pair |
267 | 267 | Repairs to automatic door closer including replacement of damaged main spring, oiling and adjusting as necessary including taking out and refitting the same. | item 267 | 50 | Each |
268 | 268 | Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately)\n(a) Upto area 2.5 Sq.m | item 268 | 1 | Sq.M |
269 | 269 | (b) Above area 2.5 Sq.m | item 269 | 1 | Sq.M |
270 | 270 | Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts) , reassembling and refitting and rehanging same with old fittings but with new screws as necessary. (Where different parts of same shutter are renewed under different item, payment under item 73 will be made once only). | item 270 | 10 | Sq.M |
271 | 271 | Taking out door and window shutters and rehanging the same with old fittings.\n(a) With new iron screws. | item 271 | 60 | Sq.M |
272 | 272 | (b) With old screws. | item 272 | 1 | Sq.M |
273 | 273 | Easing door and windows. | item 273 | 100 | Each |
274 | 274 | Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid T 2430/1510 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 4 mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Standard Ceiling Board (Density > 1300 Kg/m3) of size 595 mm X 595 mm, conforming IS 14862 & Type B Category III of ISO 8336, tested as per AS-1530 part 3 & BS-476 Part 4,5,6,7 & 8, should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in-charge.\nIn all floor\na) False Ceiling (with 6mm thick Fibre Cement Standard Ceiling Board and E- Grid T-2430/1510). | item 274 | 50 | Sq.M |
275 | 275 | Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid U-1520 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia\nG.I. wire from purlins / soffit. 15mm thick OW Acoustic Board (Mineral Fiber Acoustic Ceiling Tiles) of approved patern and size 595mm X 595mm with NRC value > 0.65 should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in-charge.\nIn all floor.\na) Acoustic False Ceiling (with 15mm thick OW Acoustic Board and E-Grid U- 1520). | item 275 | 20 | Sq.M |
276 | 276 | M.F. suspended ceiling made with 12.5 mm thick Gypsum plaster board including G.I. perimeter channel of 0.55 mm flush (having two flanges 20 mm and 30 mm respectively and web 27 mm ) along with perimeter of ceiling with G.I. intermediate channel of 0.9 mm thick size 45 mmx15mm placed at 750 mm c/c with G.I. ceiling angle of size 25 mmx10mmx0.55 mm thick fixed to the ceiling with G.I. Cleat and steel expansion fastener ceiling section 0.55 mm thick of size 51.50 mmx26mm fixed to the intermediate channels with the help of connecting clip and in the direction of perpendicular to the intermediate channel of 300 mm c/c 12.5 mm thick Gypsum plastered board are to be fixed under ceiling section as above by machine screws. The boards are to be joined and finished with jointing compound, paper tape and application of top coat etc. as per the direction of Engineer-in-charge. (The rate includes of cost of all materials including taxes, cost of accessories, fittings and fixtures, scaffolding and labour charges etc. complete)\nIn all floor | item 276 | 10 | Sq.M. |
277 | 277 | Supplying, fitting and fixing of false ceiling framework with powder coated exposed G.I. grid suspension system (E-Grid U-1520 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by\n6 mm dia G.I. wire from purlins/ soffit all complete as per the drawing & directions of Engineer-in-charge. | item 277 | 20 | Sq.M. |
278 | 278 | Supplying, fitting and fixing boiling water resistant ply conforming to IS: 303- 1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in- Charge.[excluding the cost of supporting frame work and teak wood batten/Lipping]\nIn all Floor\n(i) 4mm | item 278 | 1 | Sq.M. |
279 | 279 | (ii) 6mm | item 279 | 20 | Sq.M. |
280 | 280 | (iii) 9mm | item 280 | 1 | Sq.M. |
281 | 281 | (iv) 12mm | item 281 | 1 | Sq.M. |
282 | 282 | (v) 16mm | item 282 | 1 | Sq.M. |
283 | 283 | (vi) 19mm | item 283 | 20 | Sq.M. |
284 | 284 | Supplying, fitting and fixing boiling water proof block board conforming to IS:1659-1990 conforming to IS:848-1974 of approved make and brand, fitted and fixed as per design as per direction of Engineer-in-charge. [Excluding the cost of supporting frame work and teak wood batten/Lipping].\nIn all Floor\n(ii) 19mm | item 284 | 20 | Sq.M. |
285 | 285 | Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-in- charge.The rate includes the cost of labour, adhesive and all incidental charges thereof.\nIn all floor\nGlossy/Matt/Suede excluding surface texture or metallic lustre.\n(i) Thickness of laminate 1.5mm | item 285 | 1 | Sq.M. |
286 | 286 | (ii) Thickness of laminate 1 mm | item 286 | 50 | Sq.M. |
287 | 287 | Partition of teak veneer [1 mm] as per design fitted and fixed complete (excluding the supporting frame work & necessary teak wood battens):\nIn all floor\n(i) 4mm thick commercial quality | item 287 | 50 | Sq.M. |
288 | 288 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (all floor).[Excluding cost of chipping over concrete surface]\n(i) With 1:6 cement mortar\n(a) 25 mm thick plaster | item 288 | 1 | Sq.M |
289 | 289 | (b) 20 mm thick plaster | item 289 | 200 | Sq.M |
290 | 290 | (c) 15 mm thick plaster | item 290 | 100 | Sq.M |
291 | 291 | (ii) With 1:4 cement mortar\n(a) 20 mm thick plaster | item 291 | 1 | Sq.M |
292 | 292 | (b) 15 mm thick plaster | item 292 | 1 | Sq.M |
293 | 293 | (c) 10 mm thick plaster | item 293 | 10 | Sq.M |
294 | 294 | Labour for Chipping of concrete surface before taking up Plastering work. | item 294 | 1 | Sq.M |
295 | 295 | Closing gap between door and window frame and jambs with cement mortar (1:3) including removing old mortar (throughout entire surface of contact) and cleaning the joint. (Cement 0.012 Cu.m/100 Mtr.)\n(This item is not payable for new works). | item 295 | 1000 | Mtr |
296 | 296 | Cement washing including cleaning and smoothening surface thoroughly (cement to be used @15 kg./100 sq.m. of surface for one coat and @25 kg./100 sq.m of surface for two coats):\nExternal surface (all floor)\n(a) One coat | item 296 | 1 | Sq.M |
297 | 297 | Red oxide wash of approved shade including cleaning and smoothening surface thoroughly (without specific permission from the Engineer-in- charge this item of work must not be done on an old painted surface which has not received such red oxide wash before) :\nExternal surface (all floor)\n(a) One coat | item 297 | 1 | Sq.M |
298 | 298 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In all Floor)\n(a) One Coat\ni) Water based interior grade Acrylic Primer | item 298 | 5000 | Sq.M |
299 | 299 | ii) Solvent based interior grade Acrylic Primer | item 299 | 1 | Sq.M |
300 | 300 | (b) Two Coats\ni) Water based interior grade Acrylic Primer | item 300 | 1 | Sq.M |
301 | 301 | ii) Solvent based interior grade Acrylic Primer | item 301 | 1 | Sq.M |
302 | 302 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC.\nIn all Floor:\nOne Coat | item 302 | 1000 | Sq.M |
303 | 303 | (b) Two Coats | item 303 | 1 | Sq.M |
304 | 304 | Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface.\nTwo Coats | item 304 | 3000 | Sq.M |
305 | 305 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification.\nIn all Floor:\nOne Coat on old surface | item 305 | 1 | Sq.M |
306 | 306 | (ii) One coat on new surface. | item 306 | 100 | Sq.M |
307 | 307 | (iii) Two coats. | item 307 | 1 | Sq.M |
308 | 308 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.\nIn all floor (Two Coat)\na) Normal Acrylic Emulsion | item 308 | 1 | Sq.M |
309 | 309 | b) Premium 100% Acrylic Emulsion | item 309 | 500 | Sq.M |
310 | 310 | c) Super Protective 100% Acrylic Emulsion. | item 310 | 1 | Sq.M |
311 | 311 | Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge) | item 311 | 500 | Sq.M |
312 | 312 | Scraping and removing greasy soot from walls or ceiling of kitchen or similar smoke affected rooms and preparing the surface. | item 312 | 10 | Sq.M |
313 | 313 | Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge). | item 313 | 250 | Sq.M |
314 | 314 | Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) | item 314 | 1 | sq.m |
315 | 315 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. | item 315 | 100 | Sq.M |
316 | 316 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. | item 316 | 100 | Sq.M |
317 | 317 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :\n(a) On timber or plastered surface :\nWith super gloss (hi-gloss) -\n(i) One coat (white in shade) | item 317 | 1 | Sq.M |
318 | 318 | (ii) Two coats (white in shade) | item 318 | 1 | Sq.M |
319 | 319 | (iii) One coat (with any shade except white) | item 319 | 500 | Sq.M |
320 | 320 | (iv) Two coats (with any shade except white) | item 320 | 100 | Sq.M |
321 | 321 | With other than hi-gloss of approved quality-\n(i) One coat (white in shade) | item 321 | 1 | Sq.M |
322 | 322 | (ii) Two coats (white in shade) | item 322 | 1 | Sq.M |
323 | 323 | (iii) One coat (with any shade except white) | item 323 | 100 | Sq.M |
324 | 324 | (iv) Two coats (with any shade except white) | item 324 | 25 | Sq.M |
325 | 325 | (b) On steel or other metal surface :\nWith super gloss (hi-gloss) -\n(i) One coat (white in shade) | item 325 | 1 | Sq.M |
326 | 326 | (ii) Two coats (white in shade) | item 326 | 1 | Sq.M |
327 | 327 | (iii) One coat (with any shade except white) | item 327 | 100 | Sq.M |
328 | 328 | (iv) Two coats (with any shade except white) | item 328 | 50 | Sq.M |
329 | 329 | With other than hi-gloss of approved quality-\n(i) One coat (white in shade) | item 329 | 1 | Sq.M |
330 | 330 | (ii) Two coats (white in shade) | item 330 | 1 | Sq.M |
331 | 331 | (iii) One coat (with any shade except white) | item 331 | 1 | Sq.M |
332 | 332 | (iv) Two coats (with any shade except white) | item 332 | 1 | Sq.M |
333 | 333 | (B) Painting with superior quality aluminium paint of approved make and brand including smoothening surface by sand papering etc. on steel surface :\n(a) One coat | item 333 | 100 | Sq.M |
334 | 334 | (b) Two coats | item 334 | 1 | Sq.M |
335 | 335 | Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :\n(Two coats)\ni) Standard Quality | item 335 | 1 | Sq.M |
336 | 336 | ii) Luxury Quality | item 336 | 1 | Sq.M |
337 | 337 | French polishing to wood work including preparing surface (ordinary gloss)\n(a) On new wood work | item 337 | 50 | Sq.M |
338 | 338 | (b) On old French polished surface including complete removal of the old polish. | item 338 | 10 | Sq.M |
339 | 339 | Removing loose scales, blisters etc. from old painted surface and thoroughly smoothening the surface to make the same suitable for receiving fresh coat of paint. | item 339 | 1 | Sq.M |
340 | 340 | (a) Rendering the surface of walls and ceiling with plaster of paris\n(thickness not less than 1.5 mm.) | item 340 | 1 | Sq.M |
341 | 341 | (b) Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick) | item 341 | 500 | Sq.M |
342 | 342 | (a)Cleaning the walls and ceiling by scraping, sand papering and smoothening down the surface including putting. | item 342 | 1 | Sq.M |
343 | 343 | (b) Washing & cleaning the wall surface & ceiling by soft detergent powder & soft water & render the surface free of dust, stain etc. | item 343 | 1 | Sq.M |
344 | 344 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall)\n(i) 3 mm thick (weighing 7.4 kg/Sq.m) | item 344 | 25 | Sq.M |
345 | 345 | (ii) 4 mm thick | item 345 | 25 | Sq.M |
346 | 346 | Renewing worn out putty of glass panes :\n(a) Panes not exceeding 0.2 Sq.m | item 346 | 35 | Each |
347 | 347 | (b) Panes exceeding 0.2 Sq.m but not exceeding 0.5 Sq.m | item 347 | 1 | Each |
348 | 348 | Renewing teak wood beads of glass panes (each pane not exceeding 0.2 Sq.m) | item 348 | 1 | Each |
349 | 349 | Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-\n(A) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC.\nThe rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers.\ni ) 2 track sliding window. | item 349 | 1 | Sq.M |
350 | 350 | ii ) 3 /4 track sliding window. | item 350 | 1 | Sq.M |
351 | 351 | iii ) Openable / Casement window. | item 351 | 1 | Sq.M |
352 | 352 | iv ) Fixed glazing. | item 352 | 1 | Sq.M |
353 | 353 | v ) Louvered window. | item 353 | 1 | Sq.M |
354 | 354 | Supplying heavy duty hydraulic double action floor spring along with top pin/set of pivots conforming to IS: 6315 or any approved make as per direction of Engineer in charge. | item 354 | 10 | Each Set |
355 | 355 | Supplying heavy duty top pin/set of pivots of local make and approved by the Engineer-in-charge. (This item to be provided where floor spring not used). | item 355 | 1 | Pair. |
356 | 356 | Supplying concealed type heavy duty PVC headed aluminium tower bolt for double leaf doors as per approved make and brand as per direction of Engineer-in-Charge.\n(a) 200 mm long | item 356 | 10 | Each |
357 | 357 | (b) 250 mm long | item 357 | 10 | Each |
358 | 358 | (c) 300 mm long | item 358 | 1 | Each |
359 | 359 | (d) 450 mm long | item 359 | 1 | Each |
360 | 360 | Supplying PVC rollers for sliding windows as per direction of Engineer\nin charge. | item 360 | 1 | Each |
361 | 361 | Supplying maruti lock (100mm) | item 361 | 1 | Pair |
362 | 362 | Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.\ni) For sliding windows\na) ' T' shaped EPDM gasket for frames. | item 362 | 125 | Metre |
363 | 363 | b) 'U' shaped EPDM gasket for frames. | item 363 | 1 | Metre |
364 | 364 | ii) For openable / Casement windows\na) EPDM / weather gasket for outer frame and mullion. | item 364 | 1 | Metre |
365 | 365 | iii) weather gasket / wool pile for door vertical. | item 365 | 1 | Metre |
366 | 366 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.\ni) 4mm thick clear glass. | item 366 | 10 | Sq.M |
367 | 367 | ii) 4mm thick coloured / tinted / smoke glass. | item 367 | 10 | Sq.M |
368 | 368 | iii) 5mm thick clear glass. | item 368 | 1 | Sq.M |
369 | 369 | iv) 5mm thick coloured / tinted / smoke glass. | item 369 | 1 | Sq.M |
370 | 370 | v) 6mm thick clear glass. | item 370 | 1 | Sq.M |
371 | 371 | vi) 6mm thick coloured / tinted / smoke glass. | item 371 | 1 | Sq.M |
372 | 372 | Supplying stainless steel functional hinge for casement window as per approved brand as directed by Engineer- in -charge. (Natural White)\n(a) 250 mm long | item 372 | 1 | Each |
373 | 373 | (b) 300 mm long | item 373 | 1 | Each |
374 | 374 | Supplying annodized aluminium extruded section box hinge for casement windows as per approved brand and make directed by Engineer- in -\nCharge.(Natural White) | item 374 | 1 | Each |
375 | 375 | (A) Supplying Aluminium casted body hydraulic door closer as per I.S.I. | item 375 | 1 | Each |
376 | 376 | Filling the gap in between aluminium frame & adjacent RCC / Brick/ Stone work by providing weather silicon sealant over 6mm dia backer rod of approved quality as per architectural drawings and direction of Engineer-in-Charge complete.\nUpto 5 mm depth and 5 mm width\n(a) all Floor | item 376 | 1 | Mtr. |
377 | 377 | Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge.\n10-12 Micron thickness Annodizing film Natural white | item 377 | 30 | Kg. |
378 | 378 | Supplying, fitting & fixing of partly glazed partly panelled or fully glazed single leaf Aluminium swing door of all aluminium sections viz door frame ( top and side frame), shutter( top rail, bottom rail, lock rail, door vertical) , glazing clip made of Aluminium Alloy Extrusions conforming to IS: 733-1983 and IS: 1285-1975, annodized conforming to IS:1868- 1983, fitted with all other accessories viz. EPDM gusket,cleat, angle screws etc. including labour charges for fitting and fixing of aluminium door with door spring,/aluminium hinges, glass / Panel board all complete as per architectural drawings and direction of Engineer-in- charge.\n( Excluding cost of glass/ panel board, door spring/ Al hinges, door closer, door stoper, handle, tower bolt and locking arrangment etc)\n10-12 Micron thickness Annodizing film Natural white | item 378 | 30 | Kg. |
379 | 379 | Supplying, Aluminium Grill with F channel frame of approved make and brand having ultimate tensile strength of 19 Kg/Sq.m. and modulus of elasticity 7000 kg/ sq.m., with 15 micron anodised fitted & fixed with necessary screws etc. complete as per direction of Engineer-in-charge.\nGrill made with 10 mm wide and 5.2 mm thick aluminium sheet having expansion width of 66.00 mm and weight not less than 3.26 Kg/Sq.m. | item 379 | 10 | Sq.M. |
380 | 380 | Supplying Weather Silicone sealant of approved make and brand for fixing of grove line between the Glasses as per direction of Engineer-in- charge. for Structural Glazing/Curtain wall.\nWeather Silicone sealant for filling the Grove line between Glasses or any other material for facial work | item 380 | 100 | Mtr. |
381 | 381 | Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor).\na) In all Floor: Sizes-300 mm x300mm x10 mm with breaking strength >1200 N | item 381 | 70 | sqm |
382 | 382 | b) In all Floor: Sizes-600 mm x600mm x10 mm with breaking strength >\n1500 N | item 382 | 10 | sqm |
383 | 383 | Protective and Decorative Textured exterior high class matt finish paint of approved quality, composed of special Tharmoplastic Resin containing fine crystalline additives derive from Granite as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer | item 383 | 996 | Sq.M |
384 | 384 | BUILDING NON SCHEDULE ITEMS (refer Annexure sheet for make & model no) | item 384 | ||
385 | 385 | Supplying, fitting & fixing SS ball bearing butt hinge, 127x89x3 mm,ss matt | item 385 | 1 | Each |
386 | 386 | Supplying, fitting & fixing SS ball bearing butt hinge, 102x76x3 mm,ss matt | item 386 | 1 | Each |
387 | 387 | Supplying, fitting & fixing SS swing hinge, double action 152mm,ss matt | item 387 | 1 | Each |
388 | 388 | Supplying, fitting & fixing DCL 15 surface mounted door closer, standard arm, adj. size2-4 for max. door leaf wt. 80kg, aluminium | item 388 | 1 | Each |
389 | 389 | Supplying, fitting & fixing Mortise cylinder lockcase, 55mm backset, 72mm centres, ss matt | item 389 | 1 | Each |
390 | 390 | Supplying, fitting & fixing Euro profile thumb turn cylinder,30+30=60mm, nickel matt | item 390 | 1 | Each |
391 | 391 | Supplying, fitting & fixing Euro profile thumb turn cylinder,35+35 =70mm, nickel matt | item 391 | 1 | Each |
392 | 392 | Supplying, fitting & fixing Euro profile double cylinder, 30+30=60mm. Nickel Matt | item 392 | 1 | Each |
393 | 393 | Supplying, fitting & fixing Euro profile cylinder escutcheon press-in, ss matt | item 393 | 1 | Pair |
394 | 394 | Supplying, fitting & fixing Pull handle back to back fixing, 25mm dia X 300mm C/C, SS Matt | item 394 | 1 | Pair |
395 | 395 | Supplying, fitting & fixing Lever handle on Rose with euro profile cylinder Escutcheon, ss matt | item 395 | 1 | Pair |
396 | 396 | Supplying, fitting & fixing Mortise cylinder lockcase, 60mm backset, 85mm centres, ss matt | item 396 | 1 | Each |
397 | 397 | Supplying, fitting & fixing mortise cylinder dead bolt lock case,55mmbackset,ssmatt | item 397 | 1 | Each |
398 | 398 | Supplying, fitting & fixing Knob lockset for Bathroom, WC function, 60mm Backset, SS Matt (US 32 D) | item 398 | 1 | Each |
399 | 399 | Supplying, fitting & fixing Pull handle back to back fixing, 25mmdiax1200x900mmc/c , ss matt | item 399 | 1 | Pair |
400 | 400 | Supplying, fitting & fixing Pull handle back to back fixing,19mmdiax150c/c , ss matt | item 400 | 1 | Pair |
401 | 401 | Supplying, fitting & fixing Pull handle back to back fixing,19mmdiax200mm c/c , ss matt | item 401 | 1 | Pair |
402 | 402 | Supplying, fitting & fixing Pull handle back to back fixing, 25mm diax400mm c/c , ss matt. | item 402 | 1 | Pair |
403 | 403 | Supplying, fitting & fixing FS2104 double action floor spring with 90 degree angle hold open and ss cover plate, size 4(without accessories) max door leaf wt. 150 kg. | item 403 | 1 | Each |
404 | 404 | Supplying, fitting & fixing Double action accessories for floor spring suitable for timber door | item 404 | 1 | Each |
405 | 405 | Supplying, fitting & fixing SS-304 grade window friction stay hinges 203 mm long | item 405 | 1 | Pair |
406 | 406 | Supplying, fitting & fixing SS-304 grade window friction stay hinges 203 mm long | item 406 | 1 | Pair |
407 | 407 | Supplying, fitting & fixing side connector for glass door | item 407 | 1 | Each |
408 | 408 | Supplying, fitting & fixing overpanel connector for glass door | item 408 | 1 | Each |
409 | 409 | Supplying, fitting & fixing top pivot for glass door | item 409 | 1 | Each |
410 | 410 | Supplying, fitting & fixing top patch connector for glass door | item 410 | 1 | Each |
411 | 411 | Supplying, fitting & fixing bottom patch fittings for glass door | item 411 | 1 | Each |
412 | 412 | Supplying, fitting & fixing top patch fittings for glass door | item 412 | 1 | Each |
413 | 413 | Supplying, fitting & fixing lock for glass door | item 413 | 1 | Each |
414 | 414 | Supplying, fitting & fixing floor spring for glass door | item 414 | 1 | Each |
415 | 415 | Supplying, fitting & fixing Gride false celling board 595mm X 595mm (Make- Amstrong-DUNE MICRO LOOK RH-99) | item 415 | 1 | Each Board |
416 | 416 | Supplying, fitting & fixing 125mm long double bearing roller for aluminium sliding door of approved quality & brand. | item 416 | 1 | Each |
417 | 417 | Supplying, fitting & fixing 165mm long concealed pus type lock for aluminium sliding door of approved quality & brand. | item 417 | 1 | Set |
418 | 418 | Supplying, fitting & fixing 8M single point Euro profile "Z" handle for aluminium window of approved quality & brand. | item 418 | 1 | Each |
419 | 419 | Renewing of glass/net shutter along with necessary fixing of frame members as per alignment of other shutters complete at any level as per direction of EIC. | item 419 | 1 | Sqm |
420 | 420 | Renewing of 12mm thick toughened glass door/partition of any size with proper patch fittings complete at any level as per direction of EIC. | item 420 | 1 | Sqm |
421 | 421 | Supplying, fitting & fixing 20 mm C.P. curtain rod with plain socket of approved quality & brand. | item 421 | 50 | Rm |
422 | 422 | Supplying, fitting & fixing 25 mm C.P. curtain rod with plain socket of approved quality & brand. | item 422 | 50 | Rm |
423 | 423 | Supplying, fitting & fixing 25 mm C.P. curtain rod with fancy wooden/metal socket. | item 423 | 50 | Rm |
424 | 424 | Supplying, fitting & fixing 25 mm C.P. curtain rod Ends. | item 424 | 1 | Each |
425 | 425 | Supplying, fitting & fixing 25 mm C.P. curtain rod Mid-support. | item 425 | 1 | Each |
426 | 426 | Supplying, fitting & fixing Netlon netting with VELCO as per approved design & make. | item 426 | 1 | Sqm |
427 | 427 | Renewing netlon netting with wooden bid for fly-proof mosquito shutter. | item 427 | 1 | Sqm |
428 | 428 | Renewing nylon netting with wooden bid for fly-proof mosquito shutter. | item 428 | 1 | Sqm |
429 | 429 | Supplying, fitting & fixing "Godrej" night lock with keys 7 levers including fitting & fixing complete. | item 429 | 1 | Each |
430 | 430 | Supplying, fitting & fixing CP designer 6 point Hanger clip (300mm long) for hanging clothes. | item 430 | 1 | Each |
431 | 431 | Supplying, fitting & fixing CP designer 3 point hook for hanging clothes. | item 431 | 1 | Each |
432 | 432 | Supplying, fitting & fixing CP designer 1 point hook for hanging clothes. | item 432 | 1 | Each |
433 | 433 | Supplying, fitting & fixing RCPC Drain Cover (5MT) without frame | item 433 | 1 | Each |
434 | 434 | Labour charge for derail the sliding shutter from the track, replace the old gusket and fixing the shutter properly on the track fabrication. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers. | item 434 | 600 | Sqm |
435 | 435 | PLUMBING & SANITARY SCHEDULE ITEMS | item 435 | ||
436 | 436 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above all. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)\n(A) For Exposed Work\n(a) (i) 15 mm dia. medium quality | item 436 | 1 | Mtr |
437 | 437 | (ii) 20 mm dia. medium quality | item 437 | 1 | Mtr |
438 | 438 | (ii) 25 mm dia. medium quality | item 438 | 1 | Mtr |
439 | 439 | (ii) 32 mm dia. medium quality | item 439 | 1 | Mtr |
440 | 440 | (ii) 40 mm dia. medium quality | item 440 | 25 | Mtr |
441 | 441 | (ii) 50 mm dia. medium quality | item 441 | 100 | Mtr |
442 | 442 | (ii) 65 mm dia. medium quality | item 442 | 1 | Mtr |
443 | 443 | (ii) 80 mm dia. medium quality | item 443 | 1 | Mtr |
444 | 444 | (i) 100 mm dia. medium quality | item 444 | 1 | Mtr |
445 | 445 | (B) For Concealed Work\n(a) 15 mm dia. medium quality | item 445 | 1 | Mtr |
446 | 446 | (b) 20 mm dia. medium quality | item 446 | 10 | Mtr |
447 | 447 | (c) 25 mm dia. medium quality | item 447 | 1 | Mtr |
448 | 448 | Supplying, fitting and fixing in position G.I. pipes of TATA make for\nunderground works with all necessary accessories,specials viz.socket, bend, tee, union, cross, elbow, nipple, short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.Payment for painting will be made seperately)\n(i) 15 mm dia. medium quality | item 448 | 1 | Mtr |
449 | 449 | (ii) 20 mm dia. medium quality | item 449 | 1 | metre |
450 | 450 | (iii) 25 mm dia. medium quality | item 450 | 1 | metre |
451 | 451 | (iv) 32 mm dia. medium quality | item 451 | 1 | metre |
452 | 452 | (v) 40 mm dia. medium quality | item 452 | 1 | metre |
453 | 453 | (vi) 50 mm dia. medium quality | item 453 | 1 | metre |
454 | 454 | (vii) 65 mm dia. medium quality | item 454 | 1 | metre |
455 | 455 | (viii) 80 mm dia. medium quality | item 455 | 1 | metre |
456 | 456 | (ix) 100 mm dia. medium quality | item 456 | 1 | metre |
457 | 457 | Supplying, fitting and fixing shower of approved brand and make.\n(a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). | item 457 | 20 | Each |
458 | 458 | (ii) Chromium plated round shower with revolving joint (Equivalent to Code No. 541(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). | item 458 | 30 | Each |
459 | 459 | (iii) Chromium plated shower arm 240 mm long (Equivalent to Code No. 536(A) & Model - Tropical / Sumthing Special of ESSCO or similar\nbrand). | item 459 | 10 | each |
460 | 460 | (e) Chromium plated double coat Hook(Equivalent to Code No. 35761 & Model - KUBIX of Jaquar or similar). | item 460 | 1 | each |
461 | 461 | (f) Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook (Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar). | item 461 | 60 | each |
462 | 462 | (g) PTMT overhead shower ( Prayag or equivalent)\n(i) 75 mm round | item 462 | 1 | each |
463 | 463 | (ii) 150 mm round | item 463 | 1 | each |
464 | 464 | (h) Polythene overhead shower of approved make\n15 mm X 125 mm | item 464 | 1 | each |
465 | 465 | Supplying, fitting and fixing Peet's valve fullway gunmetal standard\npattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.).\n(i) 100 mm dia | item 465 | 1 | each |
466 | 466 | (ii) 80 mm dia | item 466 | 1 | each |
467 | 467 | (iii) 65 mm dia | item 467 | 1 | each |
468 | 468 | (iv) 50 mm dia | item 468 | 1 | each |
469 | 469 | (v) 40 mm dia | item 469 | 1 | each |
470 | 470 | (vi) 32 mm dia | item 470 | 1 | each |
471 | 471 | (vii) 25 mm dia | item 471 | 1 | each |
472 | 472 | (viii) 20 mm dia | item 472 | 1 | each |
473 | 473 | (ix) 15 mm dia | item 473 | 1 | each |
474 | 474 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).\n(i) 100 mm dia | item 474 | 1 | each |
475 | 475 | (ii) 80 mm dia | item 475 | 1 | each |
476 | 476 | (iii) 65 mm dia | item 476 | 1 | each |
477 | 477 | (iv) 50 mm dia | item 477 | 1 | each |
478 | 478 | (v) 40 mm dia | item 478 | 1 | each |
479 | 479 | (vi) 32 mm dia | item 479 | 1 | each |
480 | 480 | (vii) 25 mm dia | item 480 | 10 | each |
481 | 481 | (viii) 20 mm dia | item 481 | 10 | each |
482 | 482 | (ix) 15 mm dia | item 482 | 1 | each |
483 | 483 | Supplying, fitting and fixing bib cock or stop cock.\n(a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). | item 483 | 10 | each |
484 | 484 | (b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar | item 484 | 1 | each |
485 | 485 | (ii) Chromium plated Concealed Stop Cock (Equivalent to Code No. 514(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand). | item 485 | 1 | each |
486 | 486 | (c) (i) Chromium plated Bib Cock (angular shape with wall flange) (Equivalent to Code No. 5037 & Model - Florentine of Jaquar or similar brand). | item 486 | 1 | each |
487 | 487 | (ii) Chromium plated Bib Cock with wall flange (Equivalent to Code No. 5047 & Model - Florentine of Jaquar or similar brand). | item 487 | 1 | each |
488 | 488 | (e) PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent) 15 | item 488 | 1 | each |
489 | 489 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above all. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)\n(a) For Exposed Work\nPVC Pipes (Dia)\n15 mm | item 489 | 30 | metre |
490 | 490 | 20 mm | item 490 | 30 | metre |
491 | 491 | 25 mm | item 491 | 1 | metre |
492 | 492 | 32 mm | item 492 | 1 | metre |
493 | 493 | 40 mm | item 493 | 50 | metre |
494 | 494 | 50 mm | item 494 | 50 | metre |
495 | 495 | 65 mm | item 495 | 1 | metre |
496 | 496 | 80 mm | item 496 | 1 | metre |
497 | 497 | 100 mm | item 497 | 1 | metre |
498 | 498 | b) For Concealed Work (Dia)\n15 mm | item 498 | 30 | metre |
499 | 499 | 20 mm | item 499 | 20 | metre |
500 | 500 | 25 mm | item 500 | 1 | metre |
501 | 501 | (A) Labour for fitting and fixing G.I. pipes above all (exposed) in structures with holder bat clamps including cost of jointing materials, holder bat clamps etc.,as necessary, including cutting pipe, making threads etc. complete in all respect with two coats of painting with approved paint any height. (Payment will be made on the centre line measurement of the total pipeline including specials. Payment of painting will be paid seperately)\n(i) 15 mm dia. | item 501 | 1 | metre |
502 | 502 | (ii) 20 mm dia. | item 502 | 1 | metre |
503 | 503 | (iii) 25 mm dia. | item 503 | 25 | metre |
504 | 504 | (iv) 32 mm dia. | item 504 | 25 | metre |
505 | 505 | (v) 40 mm dia. | item 505 | 1 | metre |
506 | 506 | (vi) 50 mm dia. | item 506 | 1 | metre |
507 | 507 | (vii) 65 mm dia. | item 507 | 1 | metre |
508 | 508 | (viii) 80 mm dia. | item 508 | 1 | metre |
509 | 509 | (ix) 100 mm dia. | item 509 | 1 | metre |
510 | 510 | (B) Labour for fitting and fixing G.I. pipes above all (concealed) in structures with holder bat clamps including cost of jointing materials, holder bat clamps etc.,as necessary, including cutting pipe, making threads etc. complete in all respect with two coats of painting with approved paint any height. (Payment will be made on the centre line measurement of the total pipeline including specials. Payment of painting will be paid seperately.)\n(i) 15 mm dia. | item 510 | 1 | metre |
511 | 511 | (ii) 20 mm dia. | item 511 | 1 | metre |
512 | 512 | (iii) 25 mm dia. | item 512 | 1 | metre |
513 | 513 | Labour for fitting and fixing G.I. pipes for under all work including cost of jointing materials, cutting pipes,making threads etc. complete in all respect including cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting to G.I. pipes and specials with bituminous paint. (Payment will be made on the centre line measurement of the total pipeline including specials.\nPayment of painting to be paid seperately.)\n(i) 15 mm dia. | item 513 | 1 | metre |
514 | 514 | (ii) 20 mm dia. | item 514 | 1 | metre |
515 | 515 | (iii) 25 mm dia. | item 515 | 1 | metre |
516 | 516 | (iv) 32 mm dia. | item 516 | 1 | metre |
517 | 517 | (v) 40 mm dia. | item 517 | 1 | metre |
518 | 518 | (vi) 50 mm dia. | item 518 | 1 | metre |
519 | 519 | (vii) 65 mm dia. | item 519 | 1 | metre |
520 | 520 | (viii) 80 mm dia. | item 520 | 1 | metre |
521 | 521 | (ix) 100 mm dia. | item 521 | 1 | metre |
522 | 522 | Renewing brass spindle and valve of stop cock/bib cock/push cock/pillar\n(i) 15 mm | item 522 | 200 | each |
523 | 523 | Dismantling and refixing shower rose after cleaning. | item 523 | 100 | each |
524 | 524 | Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above all. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials.\n(a) For Exposed Work\n(i) CPVC Pipes Class-1, SDR-11\n(Dia)\n15 mm | item 524 | 25 | Mtr |
525 | 525 | 20 mm | item 525 | 25 | Mtr |
526 | 526 | 25 mm | item 526 | 25 | Mtr |
527 | 527 | 32 mm | item 527 | 1 | Mtr |
528 | 528 | 40 mm | item 528 | 1 | Mtr |
529 | 529 | 50 mm | item 529 | 1 | Mtr |
530 | 530 | (b) For Concealed Work\n(i) CPVC Pipes Class-1,SDR-11\n15 mm | item 530 | 25 | Mtr |
531 | 531 | 20 mm | item 531 | 25 | Mtr |
532 | 532 | 25 mm | item 532 | 25 | Mtr |
533 | 533 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. | item 533 | 5 | each |
534 | 534 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer\n(a) 500 litre capacity | item 534 | 1 | each |
535 | 535 | (b) 1000 litre capacity | item 535 | 1 | each |
536 | 536 | Labour for hoisting plastic water storage tank.\n(i) Upto 1500 litre capacity.\n(a) Upto 1st story from G.L. | item 536 | 1 | each |
537 | 537 | (b) Extra for each additional story | item 537 | 1 | each |
538 | 538 | Labour for lowering plastic water storage tank and stacking in places as directed.\n(i) Upto 1500 litre capacity\n(a) From 1st floor to G.L. | item 538 | 1 | each |
539 | 539 | (b) Extra for each additional story | item 539 | 1 | each |
540 | 540 | Supplying, fitting and fixing low-down cistern parts.\n(i) Internal fittings for cistern complete of approved make. | item 540 | 20 | each set |
541 | 541 | (ii) Outlet Assembly | item 541 | 20 | each |
542 | 542 | (iii) Intlet Assembly | item 542 | 20 | each |
543 | 543 | (iv) Rubber Kid | item 543 | 20 | each |
544 | 544 | (v) Knob | item 544 | 20 | each |
545 | 545 | (vi) Brackets (pair) | item 545 | 1 | each |
546 | 546 | Renewing bolts and nuts for cistern. | item 546 | 20 | Each Set |
547 | 547 | Renewing high pressure polythene ball cock of approved quality with\npolythene ball and aluminium lever complete for pipe of dia.:\n(i) 32 mm | item 547 | 20 | each |
548 | 548 | (ii) 25 mm | item 548 | 1 | each |
549 | 549 | (iii) 20 mm | item 549 | 1 | each |
550 | 550 | (iv) 15 mm | item 550 | 1 | each |
551 | 551 | Renewing polythene ball of approved quality for pipe of dia.:\n(i) 32 mm | item 551 | 20 | each |
552 | 552 | (ii) 25 mm | item 552 | 1 | each |
553 | 553 | (iii) 20 mm | item 553 | 1 | each |
554 | 554 | (iv) 15 mm | item 554 | 1 | each |
555 | 555 | Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets.\n(i) 450 mm X 300 mm size | item 555 | 1 | each |
556 | 556 | (ii) 550 mm X 400 mm size | item 556 | 5 | each |
557 | 557 | (iii) 630 mm X 450 mm size | item 557 | 1 | each |
558 | 558 | Supplying, fitting and fixing pedestal of approved make for wash basin | item 558 | 1 | each |
559 | 559 | Supplying, fitting and fixing White Vitreous China Sink in position on C.I. brackets including two coats of painting of brackets.\n(a) Plain edge sink with overflow\n(i) 610 mm X 450 mm X 200 mm | item 559 | 10 | each |
560 | 560 | Supplying, fitting and fixing stainless steel sink complete with waste\nfittings and two coats of painting of C.I. brackets.\n(a) Sink only\n(i) 530 mm X 430 mm x 180 mm | item 560 | 5 | each |
561 | 561 | (ii) 600 mm X 450 mm X 250 mm | item 561 | 1 | each |
562 | 562 | (iii) 750 mm X 450 mm X 250 mm | item 562 | 1 | each |
563 | 563 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white\nflexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.\n(i) 300 mm long | item 563 | 1 | each |
564 | 564 | (ii) 450 mm long | item 564 | 1 | each |
565 | 565 | (iii) 600 mm long | item 565 | 30 | each |
566 | 566 | (iv) 750 mm long | item 566 | 5 | each |
567 | 567 | Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.\n(i) 750 mm long | item 567 | 1 | each |
568 | 568 | (iii) 900 mm long | item 568 | 100 | each |
569 | 569 | (iv) 1050 mm long | item 569 | 1 | each |
570 | 570 | Supplying, fitting and fixing complete Bottle waste trap (Heavy Quality) (a) Chromium plated Bottle trap 32 mm with 190 mm long connecting pipe and wall flange (Equivalent to Code No. 545 & Model - Tropical / Sumthing Special of ESSCO or similar brand). | item 570 | 1 | each |
571 | 571 | Supplying, fitting and fixing Waste fittings complete.\n(a) C.P. over brass\n(i) 32 mm | item 571 | 50 | each |
572 | 572 | Supplying, fitting and fixing C.I. bracket including two coats of painting.\n(a) Wash basin, Dental spitton | item 572 | 1 | each |
573 | 573 | (b) Sink, Drain board | item 573 | 1 | each |
574 | 574 | Supplying, fitting and fixing pillar cock of approved make.\na) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model -\nTropical / Sumthing Special of ESSCO or similar brand) | item 574 | 10 | each |
575 | 575 | a) (ii) CP Pillar Cock Super Deluxe with Aerator - 15 mm. (Equivalent to Code No. 508 & Model No. Tropical / Sumthing Special of ESSCO or\nsimilar brand) | item 575 | 1 | each |
576 | 576 | e) (i) CP Centre hole Basin mixture with regular spout without popup waste system with 450 mm long braided hoses. (Equivalent to Code No.5167(B) & Model - FLORENTINE of JAQUAR or similar brand). | item 576 | 1 | each |
577 | 577 | e) (ii) CP Wall Mixture without spout but with provision for connnection to Telephone Shower and exposed pipe for Overhead shower (Equivalent to Code No. 5215 & Model - FLORENTINE of JAQUAR or similar brand) | item 577 | 1 | each |
578 | 578 | f) (ii) CP 2-way bib Cock - 15 mm, supplied, fitted and fixed. (Code\nNo.5041 & Model - FLORENTINE of JAQUAR or similar brand). | item 578 | 10 | each |
579 | 579 | g) CP Sink Cock with Regular Swinging Spout (Table Mounted Model)\n(Equivalent to Code No. 5357 of JAQUAR or similar brand). | item 579 | 5 | each |
580 | 580 | Dismantling wash basin with brackets with or without waste fittings. | item 580 | 1 | each |
581 | 581 | Refixing wash basin with brackets with or without waste fittings. | item 581 | 1 | each |
582 | 582 | Dismantling sink with brackets with or without waste fittings. | item 582 | 1 | each |
583 | 583 | Refixing sink with brackets with or without waste fittings. | item 583 | 1 | each |
584 | 584 | Dismantling pillar cock of wash basin. | item 584 | 1 | each |
585 | 585 | Refixing pillar cock of wash basin. | item 585 | 1 | each |
586 | 586 | Cleaning wash basin/ sink with acid. | item 586 | 1 | each |
587 | 587 | Cleaning sink with soda and soap. | item 587 | 1 | each |
588 | 588 | Dismantling and taking out lead / polythene waste pipe and refixing the same after removing chokage including necessary bendings/ offsets and straightening and replacement of damaged parts, if any | item 588 | 1 | each |
589 | 589 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992\n(A) (i) Single Socketed 3 Meter Length\n(a) 75 mm | item 589 | 1 | metre |
590 | 590 | (b) 110 mm | item 590 | 50 | metre |
591 | 591 | (c) 160 mm | item 591 | 10 | metre |
592 | 592 | (ii) Double Socketed 3 Meter Length\n(a) 75 mm | item 592 | 1 | metre |
593 | 593 | (b) 110 mm | item 593 | 10 | metre |
594 | 594 | (c) 160 mm | item 594 | 5 | metre |
595 | 595 | (iii) Single Socketed 1.8 Meter Length\n(a) 75 mm | item 595 | 1 | metre |
596 | 596 | (b) 110 mm | item 596 | 1 | metre |
597 | 597 | (iv) Double Socketed 1.8 Meter Length\n(a) 75 mm | item 597 | 1 | metre |
598 | 598 | (b) 110 mm | item 598 | 1 | metre |
599 | 599 | (B) Fittings\n(i) Coupler\n(a) 75 mm | item 599 | 1 | Each |
600 | 600 | (b) 110 mm | item 600 | 1 | Each |
601 | 601 | (c)160 mm | item 601 | 1 | Each |
602 | 602 | (ii) Plain Tee\n(a) 75 mm | item 602 | 1 | Each |
603 | 603 | (b) 110 mm | item 603 | 1 | Each |
604 | 604 | (c) 160 mm | item 604 | 1 | Each |
605 | 605 | (iii) Door Tee\n(a) 75 mm | item 605 | 1 | Each |
606 | 606 | (b) 110 mm | item 606 | 1 | Each |
607 | 607 | (c) 160 mm | item 607 | 1 | Each |
608 | 608 | iv) Door Tee(LH) & (RH)\n(a) 75 mm | item 608 | 1 | Each |
609 | 609 | (b) 110 mm | item 609 | 1 | Each |
610 | 610 | ix) Bend 45º\n(a) 75 mm | item 610 | 1 | Each |
611 | 611 | (b) 110 mm | item 611 | 1 | Each |
612 | 612 | (c) 160 mm | item 612 | 1 | Each |
613 | 613 | x) Bend 87.5º\n(a) 75 mm | item 613 | 1 | Each |
614 | 614 | (b) 110 mm | item 614 | 1 | Each |
615 | 615 | (c) 160 mm | item 615 | 1 | Each |
616 | 616 | xi) Door Bend (T.S.)\n(a) 75 mm | item 616 | 1 | Each |
617 | 617 | (b) 110 mm | item 617 | 1 | Each |
618 | 618 | (c) 160 mm | item 618 | 1 | Each |
619 | 619 | xii) Door Bend (LH) & (RH)\n(a) 75 mm | item 619 | 1 | Each |
620 | 620 | (b) 110 mm | item 620 | 1 | Each |
621 | 621 | xv) Vent Cowl\n(a) 75 mm | item 621 | 1 | Each |
622 | 622 | (b) 110 mm | item 622 | 1 | Each |
623 | 623 | (c) 160 mm | item 623 | 1 | Each |
624 | 624 | xvi) Pipe Clip\n(a) 75 mm | item 624 | 1 | Each |
625 | 625 | (b) 110 mm | item 625 | 1 | Each |
626 | 626 | (c) 160 mm | item 626 | 1 | Each |
627 | 627 | Scraping the hard scum of 'S' trap carefully to render the flushing flow easy after soaking with strong acid through W.C. pan on floor and also cleaning through flanged junction door underneath the ceiling including necessary scafolding and resetting the flanged door watertight by putty joints by methor labour. | item 627 | 20 | Each |
628 | 628 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.\n(a) With 'P' trap | item 628 | 1 | Each |
629 | 629 | (a) With 'S' trap | item 629 | 1 | Each |
630 | 630 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing).\n(i) 580 mm X 440 mm | item 630 | 1 | Each |
631 | 631 | (ii) 530 mm X 410 mm | item 631 | 1 | Each |
632 | 632 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75mm X 75 mm X 75 mm wooden blocks complete.\n(ii) 470 mm X 280 mm X 340 mm | item 632 | 1 | Each |
633 | 633 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete.\n(a) E.W.C.\n(ii) Plastic (hallow type) white | item 633 | 10 | Each |
634 | 634 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.\ni) Polythene Flush Pipe | item 634 | 1 | Each |
635 | 635 | Supplying, fitting and fixing urinal flush pipe fittings of approved brand.\n(a) C.P. urinal flush pipe fittings range of one | item 635 | 1 | Each |
636 | 636 | Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red\nas per I.S. 3438 / 1965 together with brass C.P. hinges.\n(i) 450 mm X 300 mm | item 636 | 1 | Each |
637 | 637 | (ii) 600 mm X 450 mm | item 637 | 1 | Each |
638 | 638 | Supplying, fitting and fixing glass shelf with aluminium guard rails.\n(a) Ordinary type with 5.5 mm sheet glass\n(i) 450 mm X 125 mm | item 638 | 1 | Each |
639 | 639 | (ii) 600 mm X 125 mm | item 639 | 1 | Each |
640 | 640 | Supplying, fitting and fixing liquid soap container.\n(c) Fibre glass | item 640 | 5 | Each |
641 | 641 | Supplying, fitting and fixing soap holder.\n(a) PTMT (Prayag or equivalent) | item 641 | 1 | Each |
642 | 642 | Supplying, fitting and fixing PTMT Smart Shelf of approved make of size\n300 mm. | item 642 | 1 | Each |
643 | 643 | Supplying, fitting and fixing towel rail with two brackets.\n(a) C.P. over brass\n(i) 25 mm dia. and 450 mm long | item 643 | 1 | Each |
644 | 644 | (ii) 25 mm dia. and 600 mm long | item 644 | 5 | Each |
645 | 645 | (iii) 25 mm dia. and 750 mm long | item 645 | 1 | Each |
646 | 646 | Dismantling E.P. or Anglo-Indian W.C. | item 646 | 10 | Each |
647 | 647 | Refixing E.P. or Anglo-Indian W.C. | item 647 | 9 | Each |
648 | 648 | Dismantling Orissa pattern W.C. including taking out of base concrete, if necessary, complete. | item 648 | 10 | Each |
649 | 649 | Refixing Orissa pattern W.C. Including cost of base concrete, if necessary,complete. | item 649 | 10 | Each |
650 | 650 | Dismantling urinal. | item 650 | 10 | Each |
651 | 651 | Refixing urinal. | item 651 | 10 | Each |
652 | 652 | Dismantling flush pipe of water closet. | item 652 | 10 | Each |
653 | 653 | Refixing flush pipe of water closet. | item 653 | 10 | Each |
654 | 654 | Cleaning I.P.W.C. with acid. | item 654 | 10 | Each |
655 | 655 | Cleaning E.P. or Anglo-Indian W.C. with acid. | item 655 | 10 | Each |
656 | 656 | Cleaning urinal with channel with acid. | item 656 | 10 | Each Set |
657 | 657 | Cleaning glazed tiles with acid. | item 657 | 1 | sq. m. |
658 | 658 | Removing chokage of water closet. | item 658 | 1 | Each |
659 | 659 | Removing chokage of urinal and waste trap. | item 659 | 10 | Each |
660 | 660 | Repairing C.P. hinges of W.C. seat. | item 660 | 100 | Each |
661 | 661 | Repairing W.C. seat with brass plate and screws. | item 661 | 1 | set |
662 | 662 | Cleaning silt of inspection pit. | item 662 | 1 | Each |
663 | 663 | Removing sludge from septic tank, soak well etc. by methor labour including\ndisposal of the same outside the compound as directed.\n(a) Upto 30 users:-\n(ii) Beyond a lead of 150 metre and outside the Municipal limit | item 663 | 10 | Each |
664 | 664 | (c) Upto 50 users:-\n(ii) Beyond a lead of 150 metre and outside the Municipal limit | item 664 | 6 | Each |
665 | 665 | (e) Upto 100 users:-\n(ii) Beyond a lead of 150 metre and outside the Municipal limit | item 665 | 4 | Each |
666 | 666 | (e) Upto 200 users:-\n(ii) Beyond a lead of 150 metre and outside the Municipal limit | item 666 | 8 | Each |
667 | 667 | Cleaning soak pit by removing the top slab and replacing inner filling with jhama bats and repairing the pit as necessary including fitting the slab | item 667 | 1 | Each |
668 | 668 | Cleaning silt of master trap pit. | item 668 | 30 | Each |
669 | 669 | PLUMBING & SANITARY NON SCHEDULE ITEMS (refer Annexure sheet for make & model no) | item 669 | ||
670 | 670 | Supplying, fitting & fixing Floor mounted EWC (S-Trap) | item 670 | 1 | Each |
671 | 671 | Supplying, fitting & fixing Seat Cover | item 671 | 1 | Each |
672 | 672 | Supplying, fitting & fixing Cistern with lid | item 672 | 1 | Each |
673 | 673 | Supplying, fitting & fixing Cistern Fiitings | item 673 | 1 | Each |
674 | 674 | Supplying, fitting & fixing Urinals | item 674 | 1 | Each |
675 | 675 | Supplying, fitting & fixing Division Plate | item 675 | 1 | Each |
676 | 676 | Supplying, fitting & fixing Corner Wash Basin | item 676 | 1 | Each |
677 | 677 | Supplying, fitting & fixing Handicapped WC, WB 46x36 with one pair mounting brakets, EWC and cistern complete with fittings and seat cover, one no hinged rail 76 cm & five nos of grab rails 60 cm. | item 677 | 1 | Each |
678 | 678 | Supplying, fitting & fixing Floor mounted EWC | item 678 | 1 | Each |
679 | 679 | Supplying, fitting & fixing Wash Basin | item 679 | 1 | Each |
680 | 680 | Supplying, fitting & fixing Pedestal for Wash Basin | item 680 | 1 | Each |
681 | 681 | Supplying, fitting & fixing Wall Hanged EWC Complete set with Accessories and Seat Cover Premium. | item 681 | 1 | Each |
682 | 682 | Supplying, fitting & fixing Floor mounted EWC (P-Trap) | item 682 | 1 | Each |
683 | 683 | Supplying, fitting & fixing Floor mounted EWC (S-Trap) | item 683 | 1 | Each |
684 | 684 | Supplying, fitting & fixing Seat Cover | item 684 | 1 | Each |
685 | 685 | Supplying, fitting & fixing Cistern. | item 685 | 1 | Each |
686 | 686 | Supplying, fitting & fixing Counter Top Wash Basin | item 686 | 1 | Each |
687 | 687 | Supplying, fitting & fixing Under Counter Wash Basin | item 687 | 1 | Each |
688 | 688 | Supplying, fitting & fixing Long body bib cock with wall flange (Continental) | item 688 | 1 | Each |
689 | 689 | Supplying, fitting & fixing Concealed Stop cock with wall flange (Continental) | item 689 | 1 | Each |
690 | 690 | Supplying, fitting & fixing Bottle trap | item 690 | 1 | Each |
691 | 691 | Supplying, fitting & fixing Wall shower Mixer (Continental) | item 691 | 1 | Each |
692 | 692 | Supplying, fitting & fixing Wall shower Mixer 3-in-1 system (Continental) | item 692 | 1 | Each |
693 | 693 | Supplying, fitting & fixing Sink Cock (Continental) | item 693 | 1 | Each |
694 | 694 | Supplying, fitting & fixing 2 way bib cock (Continental) | item 694 | 1 | Each |
695 | 695 | Supplying, fitting & fixing Urinal valve Auto closing System | item 695 | 1 | Each |
696 | 696 | Supplying, fitting & fixing Flush Valve | item 696 | 1 | Each |
697 | 697 | Supplying, fitting & fixing Toilet Roll Holder (Covered) | item 697 | 1 | Each |
698 | 698 | Supplying, fitting & fixing Toilet Roll Holder | item 698 | 1 | Each |
699 | 699 | Supplying, fitting & fixing Towel Ring | item 699 | 1 | Each |
700 | 700 | Supplying, fitting & fixing Soap Dish Holder | item 700 | 1 | Each |
701 | 701 | Supplying, fitting & fixing Towel Rack - 600 mm long | item 701 | 1 | Each |
702 | 702 | Supplying, fitting & fixing Towel Rail - 300 mm long | item 702 | 1 | Each |
703 | 703 | Supplying, fitting & fixing Cloth liner | item 703 | 1 | Each |
704 | 704 | Supplying, fitting & fixing Over head shower | item 704 | 1 | Each |
705 | 705 | Supplying, fitting & fixing Over head shower Arm | item 705 | 1 | Each |
706 | 706 | Supplying, fitting & fixing Divertor with complete set | item 706 | 1 | Each |
707 | 707 | Supplying, fitting & fixing Conceal Body for Divertor | item 707 | 1 | Each |
708 | 708 | Supplying, fitting & fixing Spout | item 708 | 1 | Each |
709 | 709 | Supplying, fitting & fixing Grab Bar 300mm | item 709 | 1 | Each |
710 | 710 | Supplying, fitting & fixing Grab Bar 600mm | item 710 | 1 | Each |
711 | 711 | Supplying, fitting & fixing Angular stop cock | item 711 | 1 | Each |
712 | 712 | Supplying, fitting & fixing Wall shower Mixer 3-in-1 system | item 712 | 1 | Each |
713 | 713 | Supplying, fitting & fixing CP Grating 125 mm dia. | item 713 | 1 | Each |
714 | 714 | Supplying, fitting & fixing CP Grating 100 mm dia. | item 714 | 1 | Each |
715 | 715 | Supplying, fitting & fixing 5.5 mm. approved quality mirror with masonite board in back (600 X 450 mm). | item 715 | 1 | Each |
716 | 716 | Supplying, fitting & fixing C.P.Towel Ring | item 716 | 1 | Each |
717 | 717 | Supplying, fitting & fixing C.P.Soap Dish | item 717 | 1 | Each |
718 | 718 | Supplying, fitting & fixing C.P.Toilet Paper Holder | item 718 | 1 | Each |
719 | 719 | Acrylic Toilet box with mirror of approved quality & make. (360X300X200). | item 719 | 1 | Each |
720 | 720 | Supplying, fitting & fixing Brass Ball cock (25 mm). | item 720 | 1 | Each |
721 | 721 | Supplying, fitting & fixing Brass Ball cock (32 mm). | item 721 | 1 | Each |
722 | 722 | Supplying, fitting & fixing Brass Ball cock (40 mm). | item 722 | 1 | Each |
723 | 723 | Renewing brasss pindle and valve of Jaquar make Bibcock, Stop cock, pillar cock and push cock, 15 mm | item 723 | 1 | Each |
724 | 724 | Supplying, fitting & fixing Syphon for Conceal Cistern. | item 724 | 1 | Each |
725 | 725 | Supplying, fitting & fixing Syphon for Cascade type EWC. | item 725 | 1 | Each |
726 | 726 | Supplying, fitting & fixing Ball Valve for Cascade type EWC. | item 726 | 1 | Each |
727 | 727 | Supplying, fitting & fixing Hinge for Seat Cover for Cascade type EWC. | item 727 | 1 | Each |
728 | 728 | Supplying, fitting & fixing 3M make film for glass | item 728 | 1 | sqm |
729 | 729 | Supplying, fitting & fixing Plastic felt | item 729 | 1 | sqm |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail