||Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.\nAll kinds of soil
||Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
||Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.
||Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering-All work Upto plinth level:\n1:4:8 ( 1 Cement: 4 fine sand : 8 graded well burnt aggregate 40 mm nominal size)
||Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering-All work Upto plinth level:\n1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt aggregate 40 mm nominal size)
||Centering shuttering including struttings, propping etc. and removal of form work for:\nFoundations, footings, bases for columns etc. for mass concrete with timber plank
||Suspended floors, roofs, landings, balconies and access platform with timber planks
||Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank.
||Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank
||Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement-\n-All work upto plinth level:\n1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
||Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies,shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing andreinforcement-\nRCC work in suspended floors, roofs having slope upto 15° landings, balconies, shelves and chajjas.\n1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
||RCC work in beams, lintels, bands, plain window sills, staircases and spiral staircases excluding precast spiral staircase.\n1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
||Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses,plinth and skirting courses, fillets, columns, pillars,piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement\nIn plinth and skirting courses, fillets, columns, pillars,posts and struts\n1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
||Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits \n50 mm thick
||Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor five level.\nThermo-Mechanically Treated bars/ Cold twisted deformed steel bars
||First class brick work in foundation and plinth including cost of all materials as required complete.\nIn cement mortar 1:6 ( 1 cement : 6 fine sand ).
||Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-\nIn cement mortar 1:4 ( 1 cement : 4 fine sand ).
||Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required.
||Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
||Supply & installation of pre painted Galvalume sheets (size, shape and pitch of corrugation as approved by Engineer-incharge) in 550mpa steel grade, made out of Cold rolled steel coated with Znic-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A 792/A782M, ASTM A90/A90M, ASTM AS 1937, ASTM A924/A92M, Alloy coating AZ150/AZ100, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins,rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thickness
||Supply & installation of pre painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Znic-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A 792/A782M, ASTM A90/A90M, ASTM AS 1937, ASTM A924/A92M, Alloy coating AZ150/AZ100, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM seal or with polymer coated J or L hooks, bolts and nuts G.I. seam bolts and nuts, G.I. plain and bitumen wishers complete for Ridges/Valley/Gutter/Flashing of width 610mm: 0.50 mm thickness
||Providing and fixing plain Multipurpose Cement board (High Pressure steam cured) as per IS : 14862 : 2000 with suitable screws for fibre cement board in ceiling etc. complete frame work to be paid separately) : \n6 mm thick cement board
||Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips etc. complete\n40 mm thick with 20 mm well burnt brick aggregate.
||Providing and fixing precast chequered terrazo tiles 22 mm thick with graded marble chips of size upto 6 mm, laid on floors, footpath & courtyard on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete. \nIn dark shade using ordinary cement
||Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :\nLocal Teak Wood
||Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 × 12 mm for fixing panelling and or\nglazing as per direction of Engineer-In-Charge. \nLocal Teak wood\n35 mm thick shutters
||Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position :\n Local Teak Wood
||Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.\nFixed to openings /wooden frames with rawl plugs screws etc.
||Providing and fixing aluminium work for doors, windows, ventilators, stair railing including hand rail and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia. and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-\nFor fixed portion of approved quality:-\nAnodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).
||For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):-\nAnodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).
||Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc.n with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item):-\nWith float glass panes of 4.0 m thickness ( weight not less than 10.0 kg / sqm )
||Providing and fixing stainless steel (SS 304 grade) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in-charge:-205 x 19 mm
||Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-\nAnodised aluminium of grade AC 15.
||12 mm cement plaster of mix\nIn cement mortar 1 : 4 ( 1 cement : 4 fine sand )
||15 mm cement plaster on the rough side of single or half brick wall of mix:\nIn cement mortar 1 : 4 ( 1 cement : 4 fine sand )
||6 mm cement plaster of mix\nIn cement mortar 1 : 3 ( 1 cement : 3 fine sand )
||Neat cement punning
||Finishing walls with textured exterior paint of required shade of approved brand and manufacture on new work ( two or more coats applied @ 3.28 litre/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete. [Payment shall be made after submission of Test Certificate issued by the Manufacturer]
||Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade. [Payment shall be made after submission of Test Certificate issued by the Manufacturer]
||Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : [Payment shall be made after submission of Test Certificate issued by the Manufacturer]\nPainting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
||Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : [Payment shall be made after submission of Test Certificate issued by the Manufacturer]\nPainting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture.
||Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.