Supply , Installation And Commissioning Of Electronics Kit , Scientific Equipment And Other Items Of Department Of Electronics-1 Op-Amp - Complete In All Respect, The Pcb Overlay Shows The Schematic And Jumper Placement For Each Circuit Including Built In Ic Regulated Power Supply, A Multi Range Digital Voltmeter And Patch Chords, Banana Jumpers Nthe Trainer Kit Should Facilitates The Practicals On Basic Op Amp Circuit, Such As Design And Realization Of Inverting And Non Inverting Amplifier, Instrumentation Amplifier, Measurement Of Cmrr, Slew Rate, Measurement Of Bias Currents, Offset Currents And Offset Voltage, It Should Also Facilitates Design And Simulation Of Phase Shift Oscillator N 2 Window Comparator- Complete In All Respect, The Pcb Overlay Shows The Schematic And Jumper Placement For Each Circuit Including Built In Ic Regulated Power Supply, Should Facilitates Design And Realization Of Circuit To Detect Presence Of A Signal Within A Specified Voltage Range ( 5-12 Volt D.C. ) And Should Also Indicate When Signal Has Stepped Outside The Specified Range 3 Fiber Optic Trainer Kit Facilitates Electrical To Optical ( E-O ) , Optical To Electrical Study, Should Support Study Of Fiber Optic Losses 4 Lvdt Kit Range: ±50 Mm Or Total 100Mm , Sensitivity : 25Mv / Cm ( + / - 5 ) , Operating Frequency : 5Khz ± 3% 5 8086 Trainer Kit Evaluation Cum Development Board, Power Supply ( Smps ) , Programmer With Boot Loader To Burn The Programs In To The Chip, Power Supply. It Should Facilitates Execution Of Program In Assembly Language, Also, The Trainer Kit Should Facilitates Interfacing Of The Following Peripherals - Led, Lcd, Keypad, Dc Motor, Stepper Motor, Servo Motor, Seven Segment Display, Spdt Switches. 6 Rapid Heating Furnace- Digital Temp ( 1130 °C ) , With Controlled Construction, Outer Body Mild Ss, Power Coated Inner Body Made Up Of Ceramic, Temp Range 400 To 1500°C, ( L X W X H:24 Inch X 16 Inch X 24 Inch ) Rating 2500 Watts 7 Voltage Controlled Oscillator- Complete In All Respect, The Pcb Overlay Shows The Schematic And Jumper Placement For Each Circuit Including Built In, Ic Regulated Power Supply And It Should Facilitates Study Of Frequency Response To The Various Input Voltage 8 Vacuum Oven Rectangular: Temp Range - 50 °C To 200 °C. Inner Chamber Of Ss And Outer Ms Sheet Powder Coated, Glass Wool Insulation, , Door With Glass Window, Digital Temperature Indicator, Vacuum Gauge, Maximum Vaccum:760 Mm Of Hg. Mains: 220 / 230 V.A.C, Nsize H X W X D: 1600, Shelves 2, Capacity In Liter: 15-20, N 9 Vacuum Pump For Vacuum Oven: Max Flow ( Liters / Min ) : 45, Max Vacuum ( Inch ) :29, Max Press ( Ps Lg ) :55, Approx Weight ( Kg ) :9 Motor Hp :1 / 3 Approx Dimensions, ( Mm ) 290 X 120 X 180. 10 Scr, Diac And Triac Trainer Kit - Complete In All Respect, The Pcb Overlay Shows The Schematic And Jumper Placement, Input Power Supply 110 - 275V ±15 % ( Smps ) , 50Hz, On Board Power Supply 5 Volt And 12 Volt D.C. On Board Voltmeter, Ammeter, It Should Facilitates Study Of D.C Characteristics Of Scr, It Should Also Facilitates I ) Design And Realization Rc Triggering ( Both Half Wave And Full Wave ) With Different Value Of Resistor Nii ) Plot The V-I Characteristics Of Scr Niii ) Plot The V-I Characteristics Of Diac Niv ) Gate Current Triggering Of Scr Nv ) Plot The V-I Characteristics Of Triac N 11 8051 Trainer Kit Evaluation Cum Development Board, Power Supply ( Smps ) , Programmer With Boot Loader To Burn The Programs In To The Chip, Power Supply. It Should Facilitates Execution Of Program In Both Assembly Language And C Language. Also, The Trainer Kit Should Facilitates Interfacing Of Following Peripherals, Led, Lcd, Keypad, Dcmotor, Steppermotor, Servo Motor, Seven Segment Display, Adc, Dac, And Relay 12 Pic Microcontroller ( Pic18f45xx ) Evaluation Cum Development Board, Power Supply, Programmer With Boot Loader To Burn The Programs In To The Chip, It Should Facilitates Execution Of Program In Both Assembly Language And C Language. Also, The Trainer Kit Should Facilitates Interfacing Of Following Peripherals, Led, Lcd, Keypad, Dcmotor, Stepper Motor, Servo Motor, Seven Segment Display, Adc, Dac, And Relay 13 Temperature Transducer Trainer Kit Which Should Facilitates Study Of Temperature Sensor ( Lm 35 ) , K Type Thermocouple, Platinum Rtd , Thermister ( Both Positive Temperature Coefficient And Negative Temperature Coefficient ) 14 Photovoltaic Trainer Kit - It Should Support Experimentation On : Characteristics Of Photovoltaic Cell, Characteristics Of Phototransistor, Characteristics Of Photoconductive Cell, Characteristics Of Pin Photodiode 15 Arm7 Controller Model: Lpc 2148, Evaluation Cum Development Board, Power Supply, Programmer With Boot Loader To Burn The Programs In To The Chip, It Should Facilitates Execution Of Program In Both Assembly Language And C Language, Usb Programmer, On Board Usb ( Uart0 ) And Uart1 Interface, On Board Temperature Sensor, Following Experiments Can Be Perform With The Help Of Peripherals Mentioned Below. Ninterfacing Of Led Ninterfacing Of 16X2 Lcd Ninterfacing Of Serial Protocol Ninterfacing Of Real Time Clock ( Rtc ) Ninterfacing Of Eeprom Memory Ninterfacing Of Adc And Dac Ninterfacing Of Stepper Motor Ninterfacing Of 4X4 Hex Keypad N 16 Iot Trainer Kit, Facilitates Demonstration Of For Input Resistance Measurement, Leds Interface , Motor Driver Interface, Color Tft Display, Serial To Usb Converter, Gsm Module, Microsd Card Socket Bluetooth Interface, Zigbee Interface, Humidity Sensor Communication Protocols Along With Softwares For Programming 17 Pressure Sensor Kit: Pcb Overlay Shows The Schematic And Jumper Placement Range 0-100 Psi, Pressure Indication Through Pressure Gauge, Sound Indication Could Be The Added Feature, It Should Facilitates Demonstration Of Pressure Transducer Output From Voltage To Current Conversion, It Should Have Multiple Test Points 18 Magnetic Hot Plate Stirrer: Hot Plate Material Ceramic, Temp Range: 50 °C- 300°C, Max Load 16 Kg, Speed Range: 100-1200 Rpm, Max Capacity 10 Liters, Dimensions: W X H X D: 48 X 37 X 14 Cm
