| 1 | 1 | PART -A\nProviding, Designing and fixing of air walker of size 1100 x 550 x 1480mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make,‘U’ shaped main frame of nominal bore 65mm (G.I.) ‘C’ Class Pipe & all other pipes of nominal bore 32mm (G.I.) ‘C’ Class. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvinized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001113 | 30 | Each |
|---|
| 2 | 2 | Providing, Designing and fixing of double sit-up station of size 1500 x 1150 x 650mm fabricated with base frame of nominal bore 50mm (G.I.) ‘C’ Class Pipe of approved make.Main frame of nominal bore 32mm (G.I.) ‘C’ Class Pipe. Leg support of nominal bore 65mm (G.I.) ‘C’ Class Pipe. Fixed on its top shall be back support made of perforated MS sheet of 2mm thickness. All pipes shall be powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing.The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvinized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001114 | 30 | Each |
|---|
| 3 | 3 | Providing, Designing and fixing air swing in a pair of size 1150 x 900 x 1250 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make, Main frame of nominal bore 50mm (G.I.) ‘C’ Class Pipe. Handle support frame of nominal bore 40mm (G.I.) ‘C’ Class Pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Foothold made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001115 | 30 | Each |
|---|
| 4 | 4 | Providing, Designing and fixing horse rider station of size 1000 x 600 x 1100 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make, Main frame of nominal bore 65mm (G.I.) ‘C’ Class Pipe. Handle support frame of nominal bore 50mm (G.I.) ‘C’ Class Pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Foothold made of nominal bore 25mm (G.I.) 'C' Class Pipe. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001116 | 30 | Each |
|---|
| 5 | 5 | Providing, Designing and fixing leg press and exercise bar of size 2000 x 600 x 1750 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of nominal bore 50mm (G.I.) ‘C’ Class Pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off emoving sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Foothold made of nominal bore 50mm (G.I.) ‘C’ Class Pipe. Seats made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001117 | 30 | Each |
|---|
| 6 | 6 | Providing, Designing and fixing pull chair in a pair of size 1950 x 700 x 2000 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of nominal bore 50mm (G.I.) ‘C’ Class Pipe. Handle frame of nominal bore 32mm (G.I.) ‘C’ Class Pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment to be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001118 | 30 | Each |
|---|
| 7 | 7 | Providing, Designing and fixing seated chest press in a pair of size 1800 x 700 x 2000 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of nominal bore 50mm (G.I.) ‘C’ Class Pipe. Handle frame of nominal bore 32mm (G.I.) ‘C’ Class Pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001119 | 30 | Each |
|---|
| 8 | 8 | Providing, Designing and fixing arm wheel in a pair of size 850 x 800 x 1800 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame wheel of nominal bore 32mm (G.I.) ‘C’ Class Pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Seat shall be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001120 | 30 | Each |
|---|
| 9 | 9 | Providing, Designing and fixing double cross walker of size 1600 x 600 x 1600 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make. Handle frame of nominal bore 32mm and nominal bore 25mm (G.I.) ‘C’ Class Pipe. Foot support frame of 100 x 50 x 2.5mm CRC rectangular pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001121 | 30 | Each |
|---|
| 10 | 10 | Providing, Designing and fixing triple twister of size 1700 x 1300 x 1300 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of nominal bore 32mm (G.I.) ‘C’ Class Pipe.Handle frame of nominal bore 32mm and nominal bore 25mm (G.I.) ‘C’ Class Pipe. Foothold plate of made of cast iron of 12mm thickness. All pipes shall be powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with concrete of minimum strength M-20 and Expansion Bolts. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001122 | 30 | Each |
|---|
| 11 | 11 | Providing, Designing and fixing rowing machine of size 1280 x 800 x 1150 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of nominal bore 65mm (G.I.) ‘C’ Class Pipe. Handle support frame of nominal bore 25mm (G.I.) ‘C’ Class Pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Foothold made of nominal bore 65mm (G.I.) ‘C’ Class Pipe. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements.The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001123 | 30 | Each |
|---|
| 12 | 12 | Providing, Designing and fixing elliptical exerciser of size 1200 x 540 x 1600 mm, fabricated with main post of nominal bore 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of nominal bore 65mm (G.I.) ‘C’ Class Pipe. Handle frame of nominal bore 32mm and nominal bore 25mm (G.I.) ‘C’ Class Pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts made of 18mm thickness galvanized rod and covered with base plate cover after the installation complete. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001124 | 30 | Each |
|---|
| 13 | 13 | Providing, designing and fixing of weight assisted Shoulder Press of minimum size 1400x1600x1150mm fabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle bars shall be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001125 | 30 | Each |
|---|
| 14 | 14 | Providing, designing and fixing of weight assisted Lat Pull Down of minimum size 1250x1100x1650mm fabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle bars shall be to be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete.All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc.Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001126 | 30 | Each |
|---|
| 15 | 15 | Providing, designing and fixing of weight Assisted Chest Press of minimum size 1350x1500x1600mm fabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle bars shall be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment to be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc. (the cement concrete and excavation work shall be paid separately). Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001127 | 30 | Each |
|---|
| 16 | 16 | Providing, designing and fixing of weight assisted Rowing Machine of minimum size 1500x1450x1650mm fabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle bars shall be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment to be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. All complete as per direction of Engineer-in-Charge. (Excavation work, cement concrete and label shall be paid separately) | BI01010001010000000000000515BI0100001128 | 30 | Each |
|---|
| 17 | 17 | Providing and fixing label of equipment made of stainless steel 0.7 mm thick and fixed to the vertical post of gym equipment with stainless steel 6 nos. rivets and instructions printed by Lazer printing with computer programme i/c text writing and photo of the equipment all complete as per direction of Engineer in charge. 220 x110 mm size | BI01010001010000000000000515BI0100001129 | 480 | Each |
|---|
| 18 | 18 | Excavating holes more than 0.10 cum & upto 0.50 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto1.5m. All kinds of soil | BI01010001010000000000000515BI0100001130 | 660 | Each |
|---|
| 19 | 19 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level 1:1.5:3 (1 Cement: 1.5 coarse sand (Zone-III) including manufactured sand derived from Recycled concrete aggregate (RCA) upto 25%: 3 graded stone aggregate 20 mm nominal size of Recycled concrete aggregate (RCA) upto 25%. | BI01010001010000000000000515BI0100001131 | 82.5 | Cum |
|---|
| 20 | 20 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil | BI01010001010000000000000515BI0100001132 | 7200 | Sqm |
|---|
| 21 | 21 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level :1:5:10 (1 cement : 5 manufactured sand derived from Recycled concrete aggregate (RCA) : 10 graded stone 40 mm nominal size recycled aggregate (RA) ). | BI01010001010000000000000515BI0100001133 | 720 | Cum |
|---|
| 22 | 22 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand including recycled stone dust uto 25% : 4 graded stone aggregate including recycled concrete aggregate upto 25%) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate | BI01010001010000000000000515BI0100001134 | 7200 | Sqm |
|---|
| 23 | 23 | Providing and fixing rubber tile flooring 25mm thick made of SBR(Styrene Butadiene Rubber) with interlocking arrangements and adhesive all complete colour and size as approved by Engineer-in- Charge | BI01010001010000000000000515BI0100001135 | 7200 | Sqm |
|---|
| 24 | 24.01 | PART - B\nAnnual comprehensive maintenance of equipments i/c SBR flooring to be carried out by the agency free of cost for first three years, after the date of completion of the work as per schedule-A, all complete as per the direction of Engineer-in-Charge. From 4rth year payment schedule shall be as follows :-\nAt the end of 4th year from the date of completion of the work | BI01010001010000000000000515BI0100001136 | 30 | Per Annum |
|---|
| 25 | 24.02 | At the end of 5th year from the date of completion of the work | BI01010001010000000000000515BI0100001137 | 30 | Per Annum |
|---|
