| 1 | 1 | Renovation of shahid smarak and providing & fixing of miner statue with open shed at NCL HQ Singrauli. | | | |
|---|
| 2 | 2 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. | | | |
|---|
| 3 | 3 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | | 11 | cum |
|---|
| 4 | 4 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. | | | |
|---|
| 5 | 5 | All kinds of soil | | 26 | cum |
|---|
| 6 | 6 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. | | | |
|---|
| 7 | 7 | All kinds of soil. | | 16 | cum |
|---|
| 8 | 8 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. | | | |
|---|
| 9 | 9 | In cement mortar | | 1.5 | cum |
|---|
| 10 | 10 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment). | | 13 | cum |
|---|
| 11 | 11 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : | | | |
|---|
| 12 | 12 | Screened through sieve of I.S. designation 20 mm | | 5 | cum |
|---|
| 13 | 13 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge | | 18 | cum |
|---|
| 14 | 14 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). | | 18 | cum |
|---|
| 15 | 15 | Fine dressing of the ground. | | 42 | sqm |
|---|
| 16 | 16 | Grassing with selection No. 1 grass including watering and maintenance of the lawn for 60 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and earth shall be paid for separately). | | | |
|---|
| 17 | 17 | With grass Turf | | 42 | sqm |
|---|
| 18 | 18 | Carriage of material by Mechanical Transport including loading, unloading and stacking | | | |
|---|
| 19 | 19 | Earth Lead - 2 Km | | 23 | cum |
|---|
| 20 | 20 | Lime, moorum, building rubbish Lead - 2 Km | | 12.5 | cum |
|---|
| 21 | 21 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. | | | |
|---|
| 22 | 22 | Granite of any colour and shade | | | |
|---|
| 23 | 23 | Area of slab upto 0.50 sqm | | 290 | sqm |
|---|
| 24 | 24 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : | | | |
|---|
| 25 | 25 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size). | | 21.2 | cum |
|---|
| 26 | 26 | 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size). | | 2.53 | cum |
|---|
| 27 | 27 | Brick work with (non modular) FALG bricks conforming to IS:12894, of class designation 7.5 average compressive strength etc. complete in all respect in foundation and plinth in:( 1 cement:6 coarse sand) | | 14 | cum |
|---|
| 28 | 28 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | | 1081 | kg |
|---|
| 29 | 29 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | | 350.8 | kg |
|---|
| 30 | 30 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : | | | |
|---|
| 31 | 31 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). | | 0.58 | cum |
|---|
| 32 | 32 | Centering and shuttering including strutting, propping etc. and removal of form for:\r\n | | | |
|---|
| 33 | 33 | Foundations, footings, bases of columns, etc. for mass concrete | | 9.6 | sqm |
|---|
| 34 | 34 | Lintels, beams, plinth beams, girders, bressumers and cantilevers | | 12 | sqm |
|---|
| 35 | 35 | Suspended floors, roofs, landings, balconies and access platform | | 10 | sqm |
|---|
| 36 | 36 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. | | | |
|---|
| 37 | 37 | Cold twisted bars | | 255 | Kg |
|---|
| 38 | 38 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). | | 2.01 | cum |
|---|
| 39 | 39 | Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete. | | 13.86 | sqm |
|---|
| 40 | 40 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : | | | |
|---|
| 41 | 41 | Two or more coats on new work | | 8 | sqm |
|---|
| 42 | 42 | Finishing walls with Acrylic Smooth exterior paint of required shade : | | | |
|---|
| 43 | 43 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | | 16.6 | sqm |
|---|
| 44 | 44 | Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. | | | |
|---|
| 45 | 45 | Two or more coats on new work | | 18 | sqm |
|---|
| 46 | 46 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | | 18 | sqm |
|---|
| 47 | 47 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : | | | |
|---|
| 48 | 48 | Water thinnable cement primer | | 18 | sqm |
|---|
| 49 | 49 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | | 5 | cum |
|---|
| 50 | 50 | 12 mm cement plaster of mix : | | | |
|---|
| 51 | 51 | 1:6 (1 cement: 6 fine sand) | | 20 | sqm |
|---|
| 52 | 52 | Lettering with black Japan paint of approved brand and manufacture | | 11200 | per letter per cm height |
|---|
| 53 | 53 | Making of bust of miners Fiber Sculpture with materials to be used as clay moulding,POP (approx size 1.22 metre height from the base of pedestal) moulding, Armachour, chipping,casting work,(Plaster of Parsi,resin fiber thick layer),colouring,labour charge with finishing complete. | | 1 | Job |
|---|
| 54 | 54 | Outside painting of office building,providing suncontrol films and replacement of vertical blinds by roller blinds | | | |
|---|
| 55 | 55 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete | | 11000 | sqm |
|---|
| 56 | 56 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : | | | |
|---|
| 57 | 57 | Two coats | | 11000 | sqm |
|---|
| 58 | 58 | Wall lining butch work upto 10m height with Dholpur stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width, including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in-charge. | | 20 | sqm |
|---|
| 59 | 59 | Supplying,P&F Sun control films complete in all respect | | 1020 | sqm |
|---|
| 60 | 60 | Supplying,P&F Deck vertical blind complete in all respect. | | 600 | sqm. |
|---|
| 61 | 61 | Supplying,P&F deck roller blind complete in all respect | | 600 | sqm |
|---|
| 62 | 62 | Construction of main entrance gate(2 nos) with roof and road divider at NCL HQ, Singrauli | | | |
|---|
| 63 | 63 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. | | | |
|---|
| 64 | 64 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | | 8.22 | cum |
|---|
| 65 | 65 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. | | | |
|---|
| 66 | 66 | All kinds of soil. | | 5.4 | cum |
|---|
| 67 | 67 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | | 27375 | kg |
|---|
| 68 | 68 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : | | | |
|---|
| 69 | 69 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). | | 5.4 | cum |
|---|
| 70 | 70 | 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). | | 5.25 | cum |
|---|
| 71 | 71 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | | 148.5 | sqm |
|---|
| 72 | 72 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : | | | |
|---|
| 73 | 73 | Ridges plain (500 - 600mm) | | 29.7 | metre |
|---|
| 74 | 74 | Gutter .(600 mm over all girth) | | 59.4 | metre |
|---|
| 75 | 75 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : | | | |
|---|
| 76 | 76 | Two or more coats on new work | | 1005 | sqm |
|---|
| 77 | 77 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. | | | |
|---|
| 78 | 78 | 110 mm diameter | | 22.5 | metre |
|---|
| 79 | 79 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.\" | | 304.5 | sqm |
|---|
| 80 | 80 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but, excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). | | 15.75 | cum |
|---|
| 81 | 81 | 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams. | | 165 | sqm |
|---|
| 82 | 82 | Finishing walls with Acrylic Smooth exterior paint of required shade : | | | |
|---|
| 83 | 83 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | | 105 | sqm |
|---|
| 84 | 84 | Carriage of material by Mechanical Transport including loading, unloading and stacking | | | |
|---|
| 85 | 85 | Lime, moorum, building rubbish Lead - 1 Km | | 13.5 | cum |
|---|
| 86 | 86 | Centering and shuttering including strutting, propping etc. and removal of form for:\r\n | | | |
|---|
| 87 | 87 | Foundations, footings, bases of columns, etc. for mass concrete | | 136.5 | sqm |
|---|
| 88 | 88 | Prov and fixing in position Sign board made of GI sheet and front portion with 4 mm thick ACP, letters area cut from ACP letter will be made of acrylic sheet( minimum 40 mm projected) letters will be pasted on ACP letters will be lighted fron inside with LED strip in each letters cmplete job. | | 774.72 | sqft |
|---|
| 89 | 89 | Total impact of GST for the purpose of CTC | BI01010001010000000000000515BI0100001129 | 1 | Nos |
|---|
