| 1 | 1 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. a) Cement mortar 1:4 (1 cement :4 coarse sand) | | 38.02 | Sqm |
|---|
| 2 | 2 | 12 mm cement plaster of mix: a) 1:6 (1 cement: 6 fine sand) | | 38.02 | Sqm |
|---|
| 3 | 3 | 15 mm cement plaster on the rough side of single or half brick wall of mix : a) 1:6 (1 cement: 6 fine sand) | | 38.02 | Sqm |
|---|
| 4 | 4 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \"T\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services\nlike diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge\n(a) GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. | | 421.97 | Sqm |
|---|
| 5 | 5 | Providing and fixing in position wall panelling at all heights with integral\ndensified calcium silicate panels/tiles of size 595 x 595mm, having\nNRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section\n(galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center\nto center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer’s specification as per direction of Engineer-in-Charge all complete. \na) With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles | | 38.02 | Sqm |
|---|
| 6 | 6 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.\na) Hot finished welded type tubes | | 1414.64 | Kg |
|---|
| 7 | 7 | Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. A)12 mm thick | | 65.06 | Sqm |
|---|
| 8 | 8 | Providing and laying Pergo original excellence or equivalent laminated flooring/skirting (class of use 32, wear resistance AC-4, impact resistant- IC 2, as per EN 13329), top surface having a multi layer composite high pressure laminate treated with aluminium oxide surface guard TM of high density fibreboard substrate specially developed cores of plank size 1200mm x 190mm (approximate) having smart lock tounge and groove joints to secure long lasting joint. The edge of the tounge and groove joints of planks shall be placed on underlay of 2 mm thick (approximate) alkali resistant polyethylene sheet ( To resist any moisture movement from the sub floor and secure floating floor installation) complete as per the directions of Engineer-in-charge.: \n(a) In flooring including edge profile etc. complete. | | 385.57 | Sqm |
|---|
| 9 | 8.1 | (b) In skirting of 60mm width (approximate) including necessary edge moulding etc. complete. | | 5.94 | sqm |
|---|
| 10 | 9 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.\n(a) Size of Tile 600x600 mm | | 37.44 | sqm |
|---|
| 11 | 10 | Cement mortar 1:4 (1 cement : 4 coarse sand) | | 3.8 | cum |
|---|
| 12 | 11 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. | | 1 | Each |
|---|
| 13 | 12 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and rackets, cutting and making good the walls wherever require: a) White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps | | 1 | Each |
|---|
| 14 | 13 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. | | 1 | Each |
|---|
| 15 | 14 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.\n(a) Flexible pipe 32 mm dia | | 2 | Each |
|---|
| 16 | 15 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :\n(a) Rectangular shape 1500x450 mm | | 1 | Each |
|---|
| 17 | 16 | Providing and fixing soil, waste and vent pipes :\n(a) Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 | | 1 | Each |
|---|
| 18 | 17 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :\n(a) 100 mm dia pipe | | 4 | Each |
|---|
| 19 | 18 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. | | 1 | Each |
|---|
| 20 | 19 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.\n(a) Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 | | 2 | Each |
|---|
| 21 | 20 | Providing and fixing plain bend of required degree.\n(a) Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 | | 2 | Each |
|---|
| 22 | 21 | Providing and fixing collar :\n(a) 100 mm Sand cast iron S&S as per IS - 1729 | | 2 | Each |
|---|
| 23 | 22 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :\n(a) Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 | | 1 | Each |
|---|
| 24 | 23 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. | | 1 | Each |
|---|
| 25 | 24 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.\n(a) 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. | | 1 | Each |
|---|
| 26 | 25 | Providing and fixing toilet paper holder :\n(a) C.P. brass | | 1 | Each |
|---|
| 27 | 26 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. a) 15 mm nominal outer dia Pipes | | 15 | metre |
|---|
| 28 | 27 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :\n(a) 25 to 40 mm nominal bore | | 2 | Each |
|---|
| 29 | 28 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :\n(a) 20 mm nominal bore | | 2 | Each |
|---|
| 30 | 29 | Providing and fixing uplasticised PVC connection pipe with brass unions :\n(a) 30 cm length 15 mm nominal bore | | 6 | Each |
|---|
| 31 | 30 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :\n(a) 15 mm nominal bore | | 2 | Each |
|---|
| 32 | 31 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :\n(a) 15 mm nominal bore | | 2 | Each |
|---|
| 33 | 32 | Providing and fixing PTMT grating of approved quality and colour.\n(a) Rectangular type with openable circular lid\n150 mm nominal size square 100 mm diameter of the inner hinged round grating | | 3 | Each |
|---|
| 34 | 33 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :\n(a)Kitchen sink with drain board : 510x1040 mm bowl depth 250 mm | | 1 | Each |
|---|
| 35 | 34 | Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.\n(a) Granite of any colour and shade (Area of slab over 0.50 sqm) | | 4 | Sqm |
|---|
| 36 | 35 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete | | 1 | Each |
|---|
| 37 | 36 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).\n(a) Sal wood | | 0.2 | cum |
|---|
| 38 | 37 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.\n(a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | | 5.67 | Sqm |
|---|
| 39 | 38 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :\n(a) 200x10 mm | | 3 | Each |
|---|
| 40 | 39 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. | | 3 | Each |
|---|
| 41 | 40 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. | | 3 | Each |
|---|
| 42 | 41 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. | | 4 | Each |
|---|
| 43 | 42 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :\n (a) For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15) | | 483.96 | Kg |
|---|
| 44 | 42.1 | (b) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost\nof EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | 1200 | 5.67 | Kg |
|---|
| 45 | 43 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately) | | 18.9 | Sqm |
|---|
| 46 | 44 | Providing and fixing 12mm thick frameless toughened glass for door shutter,windows,partition or similar work location etc. of approved brand and manufacture, including filling the gaps with sealants and making necessary holes etc. for fixing required fitting, all complete as per the direction of Engineer-in-charge(Door handl,lock and stopper etc. to be paid seperately). | | 98.97 | sqm |
|---|
| 47 | 45 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge.\n(a) Pre-laminated particle board with decorative lamination on both sides | | 56.94 | sqm |
|---|
| 48 | 46 | Providing and fixing frosted sparkle film of 3M/AVERY make or equivalent on glass in required shade and pattern fixed with recommended adhesive after proper cleaning the glass etc all complete as per the direction of Engineer-in-charge. | | 82.51 | Sqm |
|---|
| 49 | 47 | Providing & fixing Glass to glass connecter 180 degree, OGC-5 of ozone or dorma or equivalent all complete with necessary screws etc.as per manufactures specifications & direction of Engineer-in-charge. : Glass to glass connecter 180 degree, OGC-5 Stainless Steel. | | 18 | Each |
|---|
| 50 | 48 | Providing & fixing stainless steel L-connector (wall to glass) , OGC-4A of ozone or dorma or equivalent all complete with necessary screws etc. as per manufactures specifications & direction of Engineer-in-charge. : a) L-connector OGC-4A Stain less steel | | 18 | Each |
|---|
| 51 | 49 | Providing & fixing stainless steel L-connector (glass to glass) , OGC-3A of ozone or dorma or equivalent all complete with necessary screws etc. as per manufactures specifications & direction of Engineer-in-charge. : a) L-connector OGC-3A Stain less steel | | 16 | Each |
|---|
| 52 | 50 | Providing & fixing stainless steel corner patch lock with strike plate for glass door OPL-1 of ozone or droma make or equivalent all complete including necessary cutting as per manufactures specifications & direction of Engineer-in-charge. : (a) Corner Patch Lock with Strike Plate OPL-1 Stain less steel. | | 6 | Each |
|---|
| 53 | 51 | Providing & fixing H type handles of size 32x600mm for glass door OGH 55 of ozone or dorma or equivalent all complete including necessary screws as per manufactures specifications & direction of Engineer-in-charge. : a) Stainless Steel Handles of sizes 32x457 mm OGH-55. | | 6 | Set |
|---|
| 54 | 52 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. | | 236.6 | Sqm |
|---|
| 55 | 53 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: a)One or more coats on old work | | 236.6 | sqm |
|---|
| 56 | 54 | French spirit polishing :\na)Two or more coats on new works including a coat of wood filler | | 15.71 | sqm |
|---|
| 57 | 55 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : a)Thickness above 10 mm up to 25 mm | | 213.14 | sqm |
|---|
| 58 | 56 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. a) For thickness of tiles 10 mm to 25 mm | | 200 | sqm |
|---|
| 59 | 57 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead. a)Of area beyond 3 sq. metres | | 10 | Each |
|---|
| 60 | 58 | Providing and fixing 25mm thick pre-laminated medium density fibre board exterior grade ( Grade-I) IS:14587:1998 marked with one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickel plated bright finishing M.S. piano hinges conforming to IS:3818 marked with necessary screw etc all complete. | | 43.2 | sqm |
|---|
| 61 | 59 | Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. a) 40 mm | | 8 | Each |
|---|
| 62 | 60 | Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. a) Double strip (horizontal type) | | 20 | Each |
|---|
| 63 | 61 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. a)100mm | | 16 | Each |
|---|
