| 1 | 1 | Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.\n(A) Up to a depth of 2.00m below the existing ground level.\n(a) In ordinary soil | item1 | 1002.24 | cum |
|---|
| 2 | 2 | Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.\n(a).Brick on flat soling. | item2 | 958.92 | Sqm |
|---|
| 3 | 3 | Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).\n(a) In prop 1cement: 3 sand :6 coarse aggregate by volume | item3 | 33.41 | cum |
|---|
| 4 | 4 | Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete.\n(No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level)\na) From Primary Producer: TATA/SAIL/Jindal steel/Shyam steel/RINL\n(i) TMT Corrosion resistant steel (CRS) reiforcement bar | item4 | 356.07 | Qtl |
|---|
| 5 | 5 | Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:\nFoundation, footings, bases of columns, pile cap, raft and mass concrete works etc.\n(i) Using 38mm thick plank | item5 | 111.36 | Sqm |
|---|
| 6 | 6 | Sides of tie beams, grade beams etc. at or below ground level.\n(a) Using 38mm thick plank | item6 | 306 | Sqm |
|---|
| 7 | 7 | Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:\nColumns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face | item7 | 689.04 | Sqm |
|---|
| 8 | 8 | Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.\n(a) For depth not exceeding 1.0M. | item8 | 306 | Sqm |
|---|
| 9 | 9 | Providing formwork using 2mm pressed bend shuttering plate of mild sheet and tubular telescopic steel props including centering, shuttering, strutting and propping etc. complete and removal of the same for in situ reinforced concrete and plain concrete work in:\nFlat Surfaces such as soffits of suspended floors, roofs, landings and the like. | item9 | 773.98 | Sqm |
|---|
| 10 | 10 | Sloping or Battering sufaces such as sloped slabs etc. including folded plates.\n(a) Where inclination to horizontal plane does not exceed 30o requiring shuttering only on the underside. | item10 | 27 | Sqm |
|---|
| 11 | 11 | Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) \n(I) Using Mixer Machine\n(A) In substructure up to plinth level\nFoundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.\nN) Without using admixture, plasticiser\nb) M20 grade concrete or Prop. 1:1.5:3 | item11 | 153.115 | cum |
|---|
| 12 | 12 | (B) In super structure from plinth level up to 1st floor level.\nii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing.\nN) Without using admixture, plasticiser\nb) M20 grade concrete or Prop. 1:1.5:3 | item12 | 200 | cum |
|---|
| 13 | 13 | 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately)\n(A) 112mm thick brick wall\n(a) In cement mortar in proportion 1:4\n(1 cement:4 sand) | item13 | 640.63 | Sqm |
|---|
| 14 | 14 | Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.\n(I) In Sub-structure upto plinth level including dewatering if necessary\n(b) In proportion 1:4 | item14 | 67 | Cum |
|---|
| 15 | 15 | Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.\n(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading. | item15 | 712.15 | Cum |
|---|
| 16 | 16 | Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. \nb) 50mm thick | item16 | 69.39 | sqm |
|---|
| 17 | 17 | Cement concrete works in topping 1:1:2 (1cement :1sand :2 graded aggregates on R.C.C floor, tread and rise of steps finished with a floating coat of neat cement using cement slurry for bond @ 2.75 kg.of cement per sq. m. of floor to be laid in panels including curing complete as directed.\na) 15mm thick | item17 | 29.85 | sqm |
|---|
| 18 | 18 | 65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg. per square metre of floor area) including curing etc. complete as directed. | item18 | 405.38 | sqm |
|---|
| 19 | 19 | 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed.\nA) On rough side \nb) In cement mortar 1:4 | item19 | 1230 | Sqm |
|---|
| 20 | 20 | 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed.\nB) On fair side \nb) In cement mortar 1:4 | item20 | 1704.77 | Sqm |
|---|
| 21 | 21 | Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished )\na) Sliding door bolts\ni) 300mm x 16mm | item21 | 8 | Each |
|---|
| 22 | 22 | b) Tower bolts\niii) 200mm x 12mm | item22 | 76 | Each |
|---|
| 23 | 23 | c) Door handles\niii) 150mm | item23 | 38 | Each |
|---|
| 24 | 24 | Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately).\n(b) 1.60mm thick sheet \n(iii) Size 125mm x 60mm (Single rebate) | item24 | 98.5 | Rm |
|---|
| 25 | 25 | Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. \nb) Non decorative type and block board core.\n(i) 40 mm thick | item25 | 35.8 | Sqm |
|---|
| 26 | 26 | Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)\n(i) Thickness = 1.5 mm thick | item26 | 1704.77 | Sqm |
|---|
| 27 | 27 | Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.\n(a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) | item27 | 1704.77 | Sqm |
|---|
| 28 | 28 | d) Applying one coat of alkali resistance primer of approved brand and manufacture on wall surface after throughly brushing the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth. | item28 | 1230 | Sqm |
|---|
| 29 | 29 | Finishing old/ new wall with water proofing weather coat smooth anti-fungal exterior painting of Apex brand of Asian Paints and of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats) | item29 | 1230 | Sqm |
|---|
| 30 | 30 | Providing, fitting and fixing steel windows/ ventilators (openable) of standard rolled steel sections as per relevant I.S. Code-1038 joints mitred and welded with 15mmx3mmx100mm lugs embedded in cement concrete block of M-10 grade including providing and fixing of projecting hinges (not more than 65mm and not less than 15mm wide) bolting device and steel handles, peg stays of 300mm long etc. complete as per drawing including applying a priming coat of red-lead paint. | item30 | 52.45 | Sqm |
|---|
| 31 | 31 | Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed.\nVITRIFIED\niii)Executive range-2 (Sizes 600 mm x600mm and above)\ni) Nitco made\na). Imperia Series- Gres Tiles | item31 | 69.39 | Sqm |
|---|
| 32 | 32 | Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department).\ni) Of size 300mmx450mm and above | item32 | 85.12 | Sqm |
|---|
| 33 | 33 | Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish. | item33 | 61.35 | Sq.m |
|---|
| 34 | 34 | Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws.\nI Plain grill\n(c) Fixed to Brick work/ PCC/RCC | item34 | 693.6 | Kg |
|---|
| 35 | 35 | Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. \n(b). With ready mixed paint , wood primer (white). | item35 | 95 | Sqm |
|---|
| 36 | 36 | Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. \n(i).Surfaces over 100mm in width or girth.\nb). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). | item36 | 95 | Sqm |
|---|
| 37 | 37 | Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. \na). With ready mixed \"red-lead/ red oxide\" primer. | item37 | 61.2 | Sqm |
|---|
| 38 | 38 | Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.\n(i).Surfaces over 100mm in width or girth.\nb). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). | item38 | 61.2 | Sqm |
|---|
| 39 | 39 | Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.\na) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution. | item39 | 474.78 | Sqm |
|---|
| 40 | 40 | Supply, Installation, Fixing of CARBON DIOXIDE Fire Extinguisher confirming to IS: 2878 with ISI Mark.(4.5 LITERS) \nBRAND: FIRESTOP / FIREND / FIRESHIELD | item40 | 5 | Each |
|---|
| 41 | 41 | Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. \na) In exposed surfaces or in trenches. \n(ii) 110mm dia. | item41 | 27.55 | Rm |
|---|
| 42 | 42 | Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. \na) In exposed surfaces or in trenches. \n(ii) 110mm dia. | item42 | 10 | Each |
|---|
| 43 | 43 | Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. \na) In exposed surfaces or in trenches. \n(ii) 110mm dia. | item43 | 8 | Each |
|---|
| 44 | 44 | Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. \na) In exposed surfaces or in trenches. \n(ii) 110mm dia. | item44 | 10 | Each |
|---|
| 45 | 45 | Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately)\nBasin (without pedestal)\nA) Parryware make \n(b) Coloured\n(i) Star Basin 550 x 400 (Cat. No.C0450) | item45 | 4 | Each |
|---|
| 46 | 46 | Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately)\nA) Parryware make \n(a) White\n(v) Elite S Trap (Cat No.C0297) (inclusive of seat cover) | item46 | 4 | Each |
|---|
| 47 | 47 | Supplying Fitting and fixing Mono layer UV stabisised PP-R ( Poly propylene-random copolymer) Pipes, SDR-11 Fusion welded having thermal stability for hot and cold water supply conforming IS 15801-2008 including all plain PP-R fittings and brass threaded PP-R fittings and clamping, cutting and making good to the damages. \n(A)) Exposed or in trenches\nSFMC/ FUSION brand or other brand of equivalent quality.\na) PN-16 Pipe,16 mm OD,SDR-7.4 | item47 | 110 | Rm |
|---|
| 48 | 48 | (A)) Exposed or in trenches\nSFMC/ FUSION brand or other brand of equivalent quality.\nd) PN-10 Pipe,32 mm OD,SDR-11 | item48 | 45 | Rm |
|---|
| 49 | 49 | (A)) Exposed or in trenches\nSFMC/ FUSION brand or other brand of equivalent quality.\nf) PN-10 Pipe,50 mm OD,SDR-11 | item49 | 25 | Rm |
|---|
| 50 | 50 | Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately\nJaquare make \n(a)Continental /Clarion\n(i)Standard | item50 | 5 | Each |
|---|
| 51 | 51 | Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. \nSONA make \n(b) Heavy type | item51 | 5 | Each |
|---|
| 52 | 52 | Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately)\nJaquar\n(a) Continental / Clarion\n(ii)15mm dia( Angular stop cock ) | item52 | 15 | Each |
|---|
| 53 | 53 | Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed.\na) 50mm dia | item53 | 3 | Each |
|---|
| 54 | 54 | Providing fitting and fixing vitreous china squatting plate urinal with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required.\ni) Parryware make \n(i) White (Cat. No. C0503) | item54 | 3 | Each |
|---|
| 55 | 55 | Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified.\nA) Parryware make \n(ii) Wall Soap tray (Cat. No.C9951) | item55 | 5 | Each |
|---|
| 56 | 56 | Providing, fitting and fixing CP towel rail complete as directed and specified\n(b) Sona make \n(iv) Towel rail Diplomat 750mm long (Cat.No.TR-0605) | item56 | 5 | Each |
|---|
| 57 | 57 | Providing fitting and fixing Decorative Mirror complete as directed and specified.\nA) Parryware make \n(b) Size 600mm x 450mm | item57 | 4 | Each |
|---|
| 58 | 58 | Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes\n2000 litres capacity \n(a) Sintex make | item58 | 1 | Each |
|---|
| 59 | 59 | Ultra Slim T5 luminaries and Electronic ballast with 1 X 28 W T5 lamp(Crompton Greaves make Model- T5LO1128 LITE LINE/ Sleek and Ultra light extruded metal T5 luminaries and Electronic ballast with 1 X 28 W T5 lamp (Crompton Greaves make Model- T5LN28 LITE n SLIM or equivalent (Equivalent will be selected by the deptt considering the mother items rate) (equivalent PHILIPS/ WIPRO/ BAJAJ/ Havells/ HPL/ SOLAR/ JAQUAR make). | item59 | 54 | Each |
|---|
| 60 | 60 | Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator].\nPremium model 1200 mm Sweep (ORIENT PSPO make) / Premium model 1050 / 1200 mm Sweep SS-390 Deco Havells make) | item60 | 7 | Each |
|---|
| 61 | 61 | Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. \nABB, Schneider MG, legrand, Hager make)\n8 way TPN (4+24) double door | item61 | 1 | Each |
|---|
| 62 | 62 | Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. \nC Series\n(Schneider MG, legrand, Hager make)\n6 to 32A | item62 | 15 | Each |
|---|
| 63 | 63 | Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz 4P RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.\n100/300mA sensitivity 4P RCCB\n(ABB, Schneider MG, legrand, Hager make)\n63A | item63 | 1 | Each |
|---|
| 64 | 64 | Supplying with fitting and fixing panel mounting open execution 25KA 415 V 50Hz 4P MCCB (ics=icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.\n25 KA 415V 50 Hz 4P MCCB \n(Schneider, legrand, Siemens, Indo Asian make) \n63A | item64 | 1 | Each |
|---|
| 65 | 65 | Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.\nDomestic \nVentilator RX 150 mm sweep (ORIENT make), Brisk Air 150 mm sweep Louver type (Crompton make) | item65 | 5 | Each |
|---|
| 66 | 66 | Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) with phenolic laminated sheet cover ,ceiling rose (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete\n Short point up to 3.00 metre. length. | item66 | 4 | Each |
|---|
| 67 | 67 | Medium point up to 6.00 metre. Length. | item67 | 21 | Each |
|---|
| 68 | 68 | Long point up to 10.00 metre. Length. | item68 | 40 | Each |
|---|
| 69 | 69 | Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere.\n Short point up to 3.00 metre. length. | item69 | 7 | Each |
|---|
| 70 | 70 | Medium point up to 6.00 metre. Length. | item70 | 2 | Each |
|---|
| 71 | 71 | Long point up to 10.00 metre. Length. | item71 | 8 | Each |
|---|
| 72 | 72 | Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt./ Havells make), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.)\n Extra long point up to 15.00 metre. length. | item72 | 2 | Each |
|---|
| 73 | 73 | Extra long point up to 20.00 metre. Length. | item73 | 2 | Each |
|---|
| 74 | 74 | Extra long point up to 25.00 metre. Length. | item74 | 5 | Each |
|---|
| 75 | 75 | Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.\nWith 2 x 1.5 sq. mm. cable in 20 mm dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit. | item75 | 45 | Metre |
|---|
| 76 | 76 | Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system.\nWith 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit. | item76 | 180 | Metre |
|---|
| 77 | 77 | With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit. | item77 | 58 | Metre |
|---|
| 78 | 78 | With 2 x 10 sq. mm. + earth continuity with 1x 6 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit. | item78 | 65 | Metre |
|---|
| 79 | 79 | Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt\n | item79 | 1 | Each |
|---|
| 80 | 80 | Supplying including fitting fixing of ceiling fan regulator including connections etc. complete as required\nElectronic Type\n | item80 | 7 | Each |
|---|
| 81 | 81 | Supplying fitting and fixing including necessary connection as approved by the Deptt.)of Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) of following type and capacity as specified and directed by the Department. ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) \n D.O.L Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make)0.5 TO 10 HP, 0.72 TO 20 A.\n | item81 | 1 | Each |
|---|
| 82 | 82 | Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make)\n 3 & 1/2 Core A2XFY \n 50.00 Sq. mm.3 & 1/2 Core armoured U.G. cable \n | item82 | 180 | Metre |
|---|
