| 1 | 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. | BI01010001010000000000000515BI0100001113 | 51 | cum |
| 2 | 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. | BI01010001010000000000000515BI0100001114 | 9 | cum |
| 3 | 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) | BI01010001010000000000000515BI0100001115 | 6.5 | cum |
| 4 | 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) | BI01010001010000000000000515BI0100001116 | 12 | cum |
| 5 | 5 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. | BI01010001010000000000000515BI0100001117 | 52 | sqm |
| 6 | 6 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : Providing and fixing tie bolt, spring coil and plastic cone in wall shuttering complete as per the direction of Engineer-in-charge 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) | BI01010001010000000000000515BI0100001118 | 1 | cum |
| 7 | 7 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). | BI01010001010000000000000515BI0100001119 | 4 | cum |
| 8 | 8 | Centering and shuttering including strutting, propping etc. and removal of form for :Suspended floors, roofs, landings, balconies and access platform. | BI01010001010000000000000515BI0100001120 | 10 | sqm |
| 9 | 9 | Centering and shuttering including strutting, propping etc. and removal of form for : Shelves (Cast in situ). | BI01010001010000000000000515BI0100001121 | 21 | sqm |
| 10 | 10 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. | BI01010001010000000000000515BI0100001122 | 9 | metre |
| 11 | 11 | Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls. Under 20 cm wide | BI01010001010000000000000515BI0100001123 | 16 | metre |
| 12 | 12 | Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete excluding plastering of the jambs, sills and soffits. 40 mm thick | BI01010001010000000000000515BI0100001124 | 1 | sqm |
| 13 | 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Thermo-Mechanically Treated bars. | BI01010001010000000000000515BI0100001125 | 120 | kg |
| 14 | 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars. | BI01010001010000000000000515BI0100001126 | 400 | kg |
| 15 | 15 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. | BI01010001010000000000000515BI0100001127 | 13.5 | metre |
| 16 | 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) | BI01010001010000000000000515BI0100001128 | 9 | cum |
| 17 | 17 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : | BI01010001010000000000000515BI0100001129 | 6 | cum |
| 18 | 18 | Brick work 7 cm thick with common burnt clay F.P.S. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and up to floor five level. | BI01010001010000000000000515BI0100001130 | 9 | sqm |
| 19 | 19 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in. cement mortar 1:4 (1 cement : 4 coarse sand) | BI01010001010000000000000515BI0100001131 | 48 | sqm |
| 20 | 20 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) | BI01010001010000000000000515BI0100001132 | 13 | Sqm |
| 21 | 21 | Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry. | BI01010001010000000000000515BI0100001133 | 10 | sqm |
| 22 | 22 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm. | BI01010001010000000000000515BI0100001134 | 5.5 | sqm |
| 23 | 23 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1stclass hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. | BI01010001010000000000000515BI0100001135 | 11 | sqm |
| 24 | 24 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1stclass hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutter25mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws. | BI01010001010000000000000515BI0100001136 | 26 | sqm |
| 25 | 25 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: 35 mm thick shutters. with ISI marked M.S. pressed butt hinges bright finished of required size. Gamari wood. | BI01010001010000000000000515BI0100001137 | 11 | sqm |
| 26 | 26 | Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 25 mm dia. | BI01010001010000000000000515BI0100001133 | 6 | metre |
| 27 | 27 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. | BI01010001010000000000000515BI0100001134 | 234 | kg |
| 28 | 28 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm | BI01010001010000000000000515BI0100001135 | 96 | each |
| 29 | 29 | Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 150 mm | BI01010001010000000000000515BI0100001136 | 12 | each |
| 30 | 30 | Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 200 mm weighing not less than 120 gms. | BI01010001010000000000000515BI0100001137 | 36 | each |
| 31 | 31 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm | BI01010001010000000000000515BI0100001138 | 7 | each |
| 32 | 32 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 250x10 mm | BI01010001010000000000000515BI0100001139 | 20 | each |
| 33 | 33 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10 mm | BI01010001010000000000000515BI0100001140 | 2 | each |
| 34 | 34 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :125 mm | BI01010001010000000000000515BI0100001141 | 58 | each |
| 35 | 35 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper | BI01010001010000000000000515BI0100001142 | 3 | each |
| 36 | 36 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper | BI01010001010000000000000515BI0100001134 | 4 | each |
| 37 | 37 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet,mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size, complete as per manufacturers specification and direction of Engineer-in-Charge. | BI01010001010000000000000515BI0100001135 | 10 | metre |
| 38 | 38 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on both side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer’s specification & drawing.30 mm thick plain PVC door shutters. | BI01010001010000000000000515BI0100001136 | 4 | sqm |
| 39 | 39 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: | BI01010001010000000000000515BI0100001137 | 937 | kg |
| 40 | 40 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators side /top /centre hung with beading and all members such asF7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer , but excluding the cost of other fittings, complete all as per approved design (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size). | BI01010001010000000000000515BI0100001138 | 377 | kg |
| 41 | 41 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size). | BI01010001010000000000000515BI0100001139 | 185 | kg |
| 42 | 42 | Providing anf fixing fly proof wire gauge to windows, clerestory windows & doors with M.S flat 15x 3mm and nuts & bolts complete: Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides. | BI01010001010000000000000515BI0100001140 | 15 | sqm |
| 43 | 43 | Providing and fixing glass panes with putty and glazing clips in steel doors, windows,Clerstory windows. All complete with: 4.0 mm thick glass panes. | BI01010001010000000000000515BI0100001141 | 15 | sqm |
| 44 | 44 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate | BI01010001010000000000000515BI0100001142 | 27 | sqm |
| 45 | 45 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick. | BI01010001010000000000000515BI0100001143 | 85 | sqm |
| 46 | 46 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1 : 3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. | BI01010001010000000000000515BI0100001144 | 9 | sqm |
| 47 | 47 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. | BI01010001010000000000000515BI0100001145 | 23 | metre |
| 48 | 48 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. | BI01010001010000000000000515BI0100001146 | 24 | sqm |
| 49 | 49 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete. | BI01010001010000000000000515BI0100001147 | 5 | sqm |
| 50 | 50 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08%and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm | BI01010001010000000000000515BI0100001148 | 40 | sqm |
| 51 | 51 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), including grouting the joint with white cement &matching pigments etc. complete. Size of Tile 600x600 mm | BI01010001010000000000000515BI0100001149 | 6 | sqm |
| 52 | 52 | Providing and fixing plain Multipurpose Cement board ( High Pressure steam cured ) as per IS : 14862, with suitable screws for fibre cement board in ceiling etc. complete (frame work to be paid separately) :6 mm thick cement board | BI01010001010000000000000515BI0100001150 | 97 | sqm |
| 53 | 53 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | BI01010001010000000000000515BI0100001151 | 148 | sqm |
| 54 | 54 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm) | BI01010001010000000000000515BI0100001152 | 22 | metre |
| 55 | 55 | 12 mm cement plaster of mix :1:6 (1 cement : 6coarsed sand) | BI01010001010000000000000515BI0100001153 | 475 | sqm |
| 56 | 56 | 15mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement : 6 Coarse sand) | BI01010001010000000000000515BI0100001154 | 274 | sqm |
| 57 | 57 | 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) | BI01010001010000000000000515BI0100001155 | 66 | sqm |
| 58 | 58 | 6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand) | BI01010001010000000000000515BI0100001156 | 45 | sqm |
| 59 | 59 | Neat cement punning | BI01010001010000000000000515BI0100001157 | 4 | sqm |
| 60 | 60 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade; New work (two or more coats) over and including water thinnable priming coat with cement primer. | BI01010001010000000000000515BI0100001158 | 412 | sqm |
| 61 | 61 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). | BI01010001010000000000000515BI0100001159 | 237 | sqm |
| 62 | 62 | Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) | BI01010001010000000000000515BI0100001160 | 53 | sqm |
| 63 | 63 | Applying priming coat : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat) | BI01010001010000000000000515BI0100001161 | 30 | Sqm |
| 64 | 64 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. | BI01010001010000000000000515BI0100001162 | 151 | sqm |
| 65 | 65 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete | BI01010001010000000000000515BI0100001163 | 280 | sqm |
| 66 | 66 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | BI01010001010000000000000515BI0100001164 | 5.5 | cum |
| 67 | 67 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge; In cement mortar | BI01010001010000000000000515BI0100001165 | 1 | cum |
| 68 | 68 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below | BI01010001010000000000000515BI0100001166 | 29 | each |
| 69 | 69 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: Asbestos sheet | BI01010001010000000000000515BI0100001167 | 148 | sqm |
| 70 | 70 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | BI01010001010000000000000515BI0100001168 | 0.5 | cum |
| 71 | 71 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. | BI01010001010000000000000515BI0100001169 | 97 | sqm |
| 72 | 72 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. | BI01010001010000000000000515BI0100001170 | 6 | each |
| 73 | 73 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | BI01010001010000000000000515BI0100001171 | 558 | sqm |
| 74 | 74 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid | BI01010001010000000000000515BI0100001172 | 2 | each |
| 75 | 75 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. | BI01010001010000000000000515BI0100001173 | 2 | each |
| 76 | 76 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. | BI01010001010000000000000515BI0100001174 | 2 | each |
| 77 | 77 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.;Flexible pipe;32 mm dia | BI01010001010000000000000515BI0100001175 | 2 | each |
| 78 | 78 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm | BI01010001010000000000000515BI0100001176 | 2 | each |
| 79 | 79 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. | BI01010001010000000000000515BI0100001177 | 2 | each |
| 80 | 80 | Providing and fixing toilet paper holder :CP brass | BI01010001010000000000000515BI0100001178 | 2 | each |
| 81 | 81 | Providing and fixing soil, waste and vent pipes : 100 mm dia. Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989. | BI01010001010000000000000515BI0100001179 | 6 | metre |
| 82 | 82 | Providing and fixing soil, waste and vent pipes : 75 mm diameter : Sand cast iron S&S pipe as per IS: 3989. | BI01010001010000000000000515BI0100001180 | 4 | metre |
| 83 | 83 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75 mm dia Sand cast iron S&S as per IS - 3989 | BI01010001010000000000000515BI0100001181 | 4 | each |
| 84 | 84 | Providing and fixing plain bend of required degree. 100 mm Sand cast iron S&S as per IS - 3989 | BI01010001010000000000000515BI0100001182 | 2 | each |
| 85 | 85 | Providing and fixing plain bend of required degree. 75 mm Sand cast iron S&S as per IS - 3989 | BI01010001010000000000000515BI0100001183 | 4 | each |
| 86 | 86 | Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100x100x100x100mm Sand cast iron S&S as per IS - 3989 | BI01010001010000000000000515BI0100001184 | 2 | each |
| 87 | 87 | Providing and fixing terminal guard: 100 mm Sand cast iron S&S as per IS - 3989 | BI01010001010000000000000515BI0100001185 | 4 | each |
| 88 | 88 | Providing and fixing collar: 100 mm Sand cast iron S&S as per IS - 3989 | BI01010001010000000000000515BI0100001186 | 4 | each |
| 89 | 89 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 100 mm | BI01010001010000000000000515BI0100001187 | 4 | each |
| 90 | 90 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 75 mm | BI01010001010000000000000515BI0100001188 | 4 | each |
| 91 | 91 | Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 100 mm | BI01010001010000000000000515BI0100001189 | 3 | each |
| 92 | 92 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 100 mm outlet ; Sand Cast Iron S&S as per IS: 3989. | BI01010001010000000000000515BI0100001190 | 2 | each |
| 93 | 93 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour. weighing not less than 105 gms. | BI01010001010000000000000515BI0100001191 | 2 | each |
| 94 | 94 | Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colour. Weighing not less than 88 gms. | BI01010001010000000000000515BI0100001192 | 2 | each |
| 95 | 95 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. | BI01010001010000000000000515BI0100001193 | 2 | each |
| 96 | 96 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes | BI01010001010000000000000515BI0100001194 | 15 | metre |
| 97 | 97 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia. nominal bore | BI01010001010000000000000515BI0100001195 | 10 | metre |
| 98 | 98 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 32 mm dia. nominal bore | BI01010001010000000000000515BI0100001196 | 10 | metre |
| 99 | 99 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore | BI01010001010000000000000515BI0100001197 | 1 | each |
| 100 | 100 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore | BI01010001010000000000000515BI0100001198 | 2 | each |
| 101 | 101 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore | BI01010001010000000000000515BI0100001199 | 2 | each |
| 102 | 102 | Providing and fixing uplasticised PVC connection pipe with brass unions :30 cm length15 mm nominal bore | BI01010001010000000000000515BI0100001200 | 10 | each |
| 103 | 103 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 20 mm nominal bore | BI01010001010000000000000515BI0100001201 | 2 | each |
| 104 | 104 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 25 mm nominal bore | BI01010001010000000000000515BI0100001202 | 2 | each |
| 105 | 105 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 32 mm nominal bore | BI01010001010000000000000515BI0100001203 | 2 | each |
| 106 | 106 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810gms. 15 mm nominal bore. | BI01010001010000000000000515BI0100001204 | 4 | each |
| 107 | 107 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore. | BI01010001010000000000000515BI0100001205 | 6 | each |
| 108 | 108 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931; 15 mm nominal bore | BI01010001010000000000000515BI0100001206 | 12 | each |
| 109 | 109 | Providing and fixing PTMT grating of approved quality and colour. Circular type100 mm nominal dia | BI01010001010000000000000515BI0100001207 | 2 | each |
| 110 | 110 | Providing and fixing PTMT grating of approved quality and colour. Circular type125 mm nominal dia with 25 mm waste hole | BI01010001010000000000000515BI0100001208 | 2 | each |
| 111 | 111 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 20 mm nominal bore, 120 mm long. Weighing not less than 198 gms. | BI01010001010000000000000515BI0100001209 | 1 | each |
| 112 | 112 | Providing and fixing PTMT swiveling shower, 15mm nominal bore. Weighing not less than 40gms. | BI01010001010000000000000515BI0100001210 | 2 | each |
| 113 | 113 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter | BI01010001010000000000000515BI0100001211 | 4 | metre |
| 114 | 114 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design: 150 mm diameter S.W. pipe | BI01010001010000000000000515BI0100001212 | 4 | metre |
| 115 | 115 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | BI01010001010000000000000515BI0100001213 | 1 | each |
| 116 | 116 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Rectangular shape 600x450mm internal dimensions | BI01010001010000000000000515BI0100001214 | 1 | each |
| 117 | 117 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | BI01010001010000000000000515BI0100001215 | 1 | each |
