rate contract for supply of consumables/non-consumables for the department of em and trauma supply of rate contract for supply of consumables/non-consumables for the department of em and trauma , note: same tender will be used for procuring implants for tncmch patientsand the selected company has to agree to deliver the implants at the quoted rates even if asked to supply a single item, for tncmch patients. the delivery should be affected within 24 hours of raising a demand and a separate invoice has to be submitted to jipmer, for this supply.(1) all implants are to be accompanied by a representative sample. quotations without representative sample will be su mmarily rejected. (2) all implants must supply a metal certificate showing suitability of implant for surgery.quotaions without metal certificate will not be accepted. (3) form - 26 from manufacturer to be supplied, failing which quotations will be rejected.(4) only manufacturers or authorised representatives are permitted to participate in the tender process.permission from manufacturers authorising dealers must be attached. (5) suppliers must quote for the entire range of items.incomplete quotations will be su mmarily rejected.(6) samples should compulsorily accompany the tender.tender without samples will be su mmarily rejected(7) the tenderer / firm / company shall arrange for demonstration of equipment / instrument / article / implants when asked to do so at his own cost and risk during anytime before finalisation of tender.each sample should have a card affixed to the sample which should bear the following information: i. your name and address ii. tender number iii. date of opening of tender iv. item no. against which tendered v. any other relevant description deemed fit.(8) samples : wherever applicable / asked, the firms shall have to submit samples of item(s) for verification / inspection,approval, etc., if required and the firm shall have to comply with such conditions of pre supply inspection / verification and shall have to abide by the decisions / directions of hospital authority in this regard. it is, therefore, inthe own interest of the firm(s) concerned to get their proofs / samples, etc verified / inspected before effecting supply at their own cost and risk. samples of what you offer to supply should not be less than the quantity necessary for the test given in the specifications (if any) or in the schedule to tender. each sample should have a card affixed to the sample which should bear the following information: i. your name and address, ii. tender number, iii. date of opening of tender, iv. item(9) it may please be noted that sometimes, the specific size / measurement of an implant / item could only be determined by the surgeon in the operation theatre,due to individual variations in physical measurements of patients. the tenderer should be willing to provide necessary arrangements, in consultation with the concerned officer of the department in such cases, so that items within a range of sizes / measurements are available at operation to choose from. it is made clearthat only those items which are selected and used in such cases are considered for procurement and the rest / unused items in such cases are to be taken back by the tenderer at his own risk and cost. , raney clips , rust remover and lubricant low pressure spray canister400ml , eshmarch tourniquette10 cm x2 metres & 15 cm x 3 metres , skin graft blade , disposable bull dogs size: small , disposable bull dogs size: medium , cannulated drill bit 4.5x 200 , cannulated drill bit 4.5x 250 , cannulated drill bit 3.2x170mm , cannulated drill bit 2.5/2.7x150 , cannulated drill bit 2.5/2.7x170 , solid drill bit 4x300 , solid drill bit 4.5x200 , solid drill bit 4.5x250 , solid drill bit 3.2x200 , solid drill bit 3.2x250 , washers[for 6.5 mm screws] , washers[for 4.0 mm screws ] , ss wires16guage , ss wires18 guage , ss wires20 guage , ss wires22 guage , non threaded single ended k wires 1.8x 12” , non threaded double ended k wires 1.8x 12” , non threaded single ended k wires 2 x 12” , non threaded double ended k wires 2 x 12” , non threaded single ended k wires 2.5 x 12” , non threaded double ended k wires 2.5 x 12” , non threaded double ended k wires 1 x 10” , non threaded double ended k wires 1.2 x 10” , non threaded double ended k wires 1.5 x 10” , non threaded double ended k wire 3x10 , non threaded double ended k wire 3.5x10 , steinmen pins 3.5mmx150, 3.5mmx200 each , steinmen pins 4mmx150, 4mmx200 each , steinmen pins 4.5mmx150, 4.5mmx200 each , steinmen pins 5mmx300mm , durhams pins 3.5mmx250, 3.5mmx200 , durhams pins 4mmx150, 4mmx200 , durhams pins 4.5mmx250, 4.5mmx200 , 3.5mm cortical screws 12 mm , 3.5mm cortical screws 14 to 44 mmsize: 14,16,18,20,22,24,26,28,30,32,34,36,38,40,42,44 mm , 3.5mm cortical screws 46 to 60 mmsize: 46,48,50,52,54,56,58,60 mm , 4.5mm cortical screws 18 to 40 mmsize: 18,20,22,24,26,28,30,32,34,36,38,40 mm , 4.5mm cortical screws 42 to 60 mm size : 42,44,46,48,50,52,54,56,58,60 mm , 2.4 mm drill type beath pin (12 inch long) , gigli saw wire thick , gigli saw wire cutter for craniotomy should not fray/break on using. sterilizable. small round low profile loops at either end. [identical sample should be provided before selection] , 2 mm guide wire beaded - 100 or 120cm , 2 mm guide wire non-beaded - 100 or 120cm , dhs dhs- i) the complete set of instruments should be supplied on loaner basis ii) supplier should be ready to exchange unused implants for required sizes iii) implants should be made of surgical grade stainless steel iv) compatiable 4.5mm cortical screws also to be supplied , dhs short barrel3h , dhs short barrel4h , dhs short barrel5h , dhs short barrel 6h , dhs short barrel7h , dhs short barrel 8h , dhs short barrel9h , dhs short barrel10h , dhs long barrel 3h , dhs long barrel 4h , dhs long barrel 5h , dhs long barrel 6h , dhs long barrel 7h , dhs long barrel 8h , dhs long barrel 9h , dhs long barrel 10h , richard screw with compression screw 60 mm , richard screw with compression screw 65 mm , richard screw with compression screw 70 mm , richard screw with compression screw 75 mm , richard screw with compression screw 80 mm , richard screw with compression screw 85 mm , richard screw with compression screw 90 mm , richard screw with compression screw 95 mm , richard screw with compression screw 100 mm , richard screw with compression screw 105 mm , ex fix items , tubular rods for external fixators size: 100,150,200,250mm , tubular rods for external fixators size: 300,350 mm , tubular rod for external fixatorssize: 400,450mm , a.o single pin clamp , metaphyseal win pin clamp , tube to tube clamp , twin clamps , 25 mm threaded pointed trochar tip scahnz pin (4mmx150) , 32 mm threaded pointed trochar tip scahnz pin (4mmx150) , 25,32,40mm threaded pointed trochar tip scahnz pin 4mmx170 , 25,32,40mm threaded pointed trochar tip scahnz pin 4mmx200 , 25,32,40mm threaded pointed trochar tip scahnz pin 4.5x170 , 25,32,40mm threaded pointed trochar tip scahnz pin 4.5x200 , 30 mm cancellous threaded pointed trochar tip scahnz pin (4.5mmx200) , 20 mm, 30 mm, 40 mm threaded pointed trochar tip scahnz pin (5mmx200) , 20 mm, 30 mm, 40 mm threaded pointed trochar tip scahnz pin (5mmx170) , 30 mm, 40 mm cancellous threaded pointed trochar tip scahnz pin (5mmx200) , 25 mm, 40 mm, 60 mm conical tapered threaded pointed trochar tip scahnz pin (6mmx200) , 25 mm, 40 mm, 60 mm cancellous threaded pointed trochar .tip scahnz pin (6mmx200) , double loaded suture anchor i) should be made of titanium ii) suture should be non absorbable and of high tensile strength iii) sutures should have needle attachedsize: 3mm and 5 mm , illizarov items , 5/8 rings 160 mm ,180mm , bayonet wires 1.5 mm , bayonet wires 1.8 mm , centric bolts , combination wrench 10-11 , conical washer sets , connectingbolts 12,14,16 mm , connecting nuts , connecting plates 2h,3h,4h,5hole , connecting plates 6h,7h,8h,9hole , cubes 2h,3h,4h,5h , eccentric bolts , female post 1h,2h, 3h,4h,5h , flat washers , half rings150,160, 180 mm , illizarov box spanner for bolts for illizarov , illizarov box spanner for nuts for illizarov , italian arch14090 degree , italian arch140 120 degree , italian arch16090 degree , italian arch160 120 degree , italian arch18090 degree , italian arch180 120 degree , male post1h,2h,3h,4h,5h , oblique support , olive wires - trocar tip& bayonet tip , rods ,110,130,150mm , rods 220,240,260,280,300,320,340,360,380,400 mm , schanz pin holding clamp , trocar wires 1.5 mm , trocar wires 1.8 mm , twisted plates1h,2h,3h,4h,5h , antegrade femur nail i) unit: each femoral interlocking nail unit consist of femoral interlocking nail - 1 no& 4.9 interlock bolts x 4 nos or3.9 x 4 nos corresponding to nail size ii) supplier should be ready to exchange unused implants for required sizes iii) implants should be made of surgical grade stainless steel iv)complete instrumentation set should be supplied on loaner basis v) price should be quoted for complete unit , interlocking femur nail 9 x 32, 9 x 44, 9 x 46 , interlocking femur nail 10 x 32, 10 x 44, 10 x 46 , interlocking femur nail 11 x 32, 11 x 44 , interlocking femur nail 11 x 46 , interlocking femur nail 9 x 34, 9 x 36, 9 x 38, 9 x 40 , interlocking femur nail 9 x 42 , interlocking femur nail 10 x 34, 10 x 36, 10 x 38, 10 x 40 , interlocking femur nail 10 x 42 , interlocking femur nail 11 x 34, 11 x 36, 11 x 38, 11 x 40 , interlocking femur nail 11 x 42 , interlocking femur nail 12 x 32, 12 x 34, 12 x 36, 12 x 38 , interlocking femur nail 12 x 40, 12 x 42, 12 x 44, 12 x 46 , tibial interlocking nail i) unit: each tibial interlocking nail unit consist of tibial interlocking nail - 1 no& 4.9 interlock bolts x 4 nos or3.9 x 4 nos corresponding to nail sizeii) supplier should be ready to exchange unused implants for required sizes iii) implants should be made of surgical grade stainless steel iv)complete instrumentation set should be supplied on loaner basis v) price should be quoted for complete unit , interlocking tibial nail 9 x 28, 9 x 30, 9 x 32 , interlocking tibial nail 10 x 28, 10 x 30, 10 x 32 , interlocking tibial nail 8 x 34, 8 x 36, 8 x 38 , interlocking tibial nail 9 x 34, 9 x 36, 9 x 38 , interlocking tibial nail 10 x 34, 10 x 36, 10 x 38 , vanna scissors - angled (angled, 8.0mm, flat handle , overall length 90mm ) , long pfnunit: each proximal femoral nail unit consist of(i) proximal femoral nail - 1 no, 8 mm cannulated locking boltx 1 no. 6 mm cannulated locking boltx 1 no. 4.9 mm locking bolt x 2 nos.ii) supplier should be ready to exchange unused implants for required sizes iii) implants should be made of surgical grade stainless steeliv)complete instrumentation set should be supplied on loaner basisv) price should be quoted for complete unit , long pfn ( right & left )9 x 32, 9 x 42, 9 x 44 , long pfn ( right & left ) 10 x 32, 10 x 42, 10 x 44 , long pfn( right & left ) 11 x 32, 11 x 42, 11 x 44 , long pfn( right & left )9 x 34, 9 x 36, 9 x 38, 9 x 40 , long pfn ( right & left ) 10 x 34, 10 x 36, 10 x 38, 10 x 40 , long pfn ( right & left )11 x 34, 11 x 36, 11 x 38, 11 x 40 , monoaxial spine pedicle screws i)should be made of surgical grade titanium ii) should be compatible with 5.5 mm rod systemiii) prices quoted should be inclusive of set screwiv) supplier should supply the complete set of instruments including awl, taps, screw drivers, handles, rod holders, pedicle sounds, pedicle finders, persuaders, compressors, distractors on loaner basis still stocks lastv) inventory with all screw sizes should be maintained in jipmervi) supplier should be ready to exchange unused screws for required sizes , monoaxial screws 4.5 x 25 , monoaxial screws 4.5 x 30 , monoaxial screws 4.5 x 35 , monoaxial screws 5.5 x 30 , monoaxial screws 5.5 x 35 , monoaxial screws 5.5 x 40 , monoaxial screws 5.5 x 45 , monoaxial screws 6.5 x 30 , monoaxial screws 6.5 x 35 , monoaxial screws 6.5 x 40 , monoaxial screws 6.5 x 45 , polyaxial spine pedicle screws i)should be made of surgical grade titaniumii) should be compatible with 5.5 mm rod systemiii) prices quoted should be inclusive of set screwiv) supplier should supply the complete set of instruments including awl, taps, screw drivers, handles, rod holders, pedicle sounds, pedicle finders, persuaders, compressors, distractors on loaner basis still stocks lastv) inventory with all screw sizes should be maintained in jipmer vi) supplier should be ready to exchange unused screws for required sizes , polyaxial screws 4.5 x 25 , polyaxial screws 4.5 x 30 , polyaxial screws 4.5 x 35 , polyaxial screws 5.5 x 30 , polyaxial screws 5.5 x 35 , polyaxial screws 5.5 x 40 , polyaxial screws 5.5 x 45 , polyaxial screws 6.5 x 30 , polyaxial screws 6.5 x 35 , polyaxial screws 6.5 x 40 , polyaxial screws 6.5 x 45 , 5.5mm titanium rod for use with spine pedicle screw (400 mm) , 4.5 mmlocking platesi)supplier should supply the complete set of instruments including drill bit, threaded drill sleeve and screw driver with compatiable screws ii) implants should be made of surgical grade stainless steel iii) one unit includes plate 1 no along with appropriate number and type of locking screws according to the number of plate holesiii) supplier should be ready to exchange unused screws for required sizes , 4.5mm narrowlcp 5h, 6h,7h, 8h, 10h , 4.5mm narrowlcp 12,14,16 hole , 4.5mm broad lcp 5h, 6h,7h, 8h, 10h , 4.5mm broad lcp 12,14,16 hole , recon lcp 4h,6h,7h, 8h,10h,12h,14h,16h , proximal femur locking lcp i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes. ii)plate head should have atleast five locking screw holes and should be a combination of 6.5/7 mm and 4.5/5 mm and shaft should have combi holes iii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmer v) supplier should be ready to exchange unused implants for required sizesvi) prices quoted should be inclusive of screw costsvii) implants should be made of surgical grade stainless steelviii) sizes required: left : 6 h,8h,10h,12h,14hright : 6h,8h,10h,12h,14h , distal femur locking lcp i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes.ii) plate head should have atleast six locking screw holes and should be a combination of 6.5/7 mm and 4.5/5 mm and shaft should have combi holesiii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks lastiv) inventory with all screw sizes should be maintained in jipmer v) supplier should be ready to exchange unused plates for required sizes distal femur locking lcpvi) prices quoted should be inclusive of screw costsvii) implants should be made of surgical grade stainless steel viii) sizes required: left: 5h,6h,8h,10h,12h,14h right: 5h,6h,8h,10h,12h,14h , 3.5mm medial proximal tibial locking lcp i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes. ii) plate head should have atleast four locking screw holesand shaft should have combi holesiii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmerv) supplier should be ready to exchange unused plates for required vi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steelviii) sizes requiredleft: 3h,4h,6h,8h,10hright: 3h 4h,6h,8h,10h , 3.5 mm lateral proximal tibial locking lcp i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes.ii) plate head should have atleast five locking screw holesand shaft should have combi holes iii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmerv) supplier should be ready to exchange unused plates for required sizes vi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steelviii) sizes required left:3h,4h,6h,8h,10h right: 3h,4h,6h,8h,10h , 4.5mm lateral proximal tibial locking lcp i) unit: 1 unit consists of plate-1 no.,4/5/6.5 mm locking screws- 4 nos. for plate head, 4.5/5 mm locking cortical screws - 4 nos. for plate shaftii) plate head should have atleast four locking screw holesand shaft should have combi holes.iii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmerv) supplier should be ready to exchange unused plates for required sizes left:3h,4h,6h,8h,10h,12h,14h right: 3h,4h,6h,8h,10h,12h,14h , 3.5 mm postero mdial proximal tibial locking lcp i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes. ii) plate head should have atleast four locking screw holesand shaft should have combi holes iii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks lastiv) inventory with all screw sizes should be maintained in jipmer v) supplier should be ready to exchange unused implants vi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steel viii)sizes required sizes 2h,4h,6h , 3.5/4mm antero lateral distal tibial anatomical locking lcp i) unit: 1 unit consists of plate-1 no. and screws as per number and type of plate holes ii) price quoted should be inclusive of screwsiii) plate head should have atleast five locking screw holesand shaft should have combi holesiv) suppliershould supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last v) inventory with all screw sizes should be maintained in jipmer vi) supplier should be ready to exchange unused plates for required sizes as and when need arises vii) plate sizes required left: 4h,6h,8h,10h,12h right: 4h,6h,8h,10h,12hviii) plate and screws should be made of surgical grade stainless steel , 3.5/4 mm medial distal tibial anatomical locking lcp i) unit: 1 unit consists of plate-1 no. and screws as per number and type of plate holesii) price quoted should be inclusive of screws iii) plate head should have atleast five locking screw holesand shaft should have combi holesiv) suppliershould supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last v) inventory with all screw sizes should be maintained in jipmer vi) supplier should be ready to exchange unused plates for required sizes as and when need arises vii) plate sizes required left: 6h,8h,10h,12h right: 6h,8h,10h,12h viii) plate and screws should be made of surgical grade stainless steel , antero lateral distal tibial lcp 4h to 8hole , short pfnunit: each proximal femoral nail unit consist of(i) proximal femoral nail - 1 no, 8 mm cannulated locking boltx 1 no. 6 mm cannulated locking boltx 1 no. 4.9 mm locking bolt x 2 nos.ii) supplier should be ready to exchange unused implants for required sizes iii) implants should be made of surgical grade stainless steel iv)complete instrumentation set should be supplied on loaner basis v) price should be quoted for complete unit , short pfn 9 x 240 mm , short pfn 10 x 240 mm , short pfn 11 x 240 mm , 3.5 mm system plates , 3.5mm system plates dcp 4h , 3.5mm system plates dcp 5h , 3.5mm system plates dcp 6h , 3.5mm system plates dcp 7h , 3.5mm system plates dcp 8h , 3.5mm system plates dcp 9h to 14 hole , 3.5mm calcaneal perimeter plate , lcdcp 5 hole to 8 hole , lcdcp 9 hole to 14 hole , 1/3 tubular plates 4h, 9h, 10h, 11h, 12hole , 1/3 tubular plates 5h, 6h, 7h, 8h , t plates 3h , t plates 4h , t plates 5h , t plates 6h , t plates 7h , t plates 8h , oblique t plates [rt] 3h , oblique t plates [lt] 3h , oblique t plates [rt] 4h , oblique t plates [lt] 4h , oblique t plates [rt] 5h , oblique t plates [lt] 5h , oblique t plates [rt] 6h , oblique t plates [lt] 6h , oblique t plates [rt] 7h , oblique t plates [lt] 7h , oblique t plates [rt] 8h , oblique t plates [lt] 8h , 4.5mm system plates narrow dcp 4h , 4.5mm system plates narrow dcp 5h , 4.5mm system plates narrow dcp 6h , 4.5mm system plates narrow dcp 7h , 4.5mm system plates narrow dcp 8h , 4.5mm system plates narrow dcp 9h , 4.5mm system plates narrow dcp 10h , 4.5mm system plates narrow dcp 12h , 4.5mm system plates narrow dcp 14h , 4.5mm system plates narrow dcp 16h , 4.5 mm system plates broad dcp 4,5,6,7,8,9,10 hole ( each 50) , 4.5 mm system plates broad dcp 12 and 14 hole , 4.5mm recon plates 4,5,6,7,8,9,10,11,12 hole , 4.5mm t butress plates [3h, 4h, 5h, 6h, 7h, 8h] , 4.5mm l butress plates [rt & lt : 4h, 5h, 6h, 7h, 8h] , 3.5mm locking lcp 4h, 6h, 8h, 10h, 12h, 14h, 16 hole (each size 10nos) - supplier should supply the complete set of instruments including drill bit, threaded drill sleeve , screw driver with compatible screws , recon locking plates 4h, 6h, 8h, 10h, 12h, 14h, 16 hole , 2.4/2.7/3.5 anatomical locking plates , proximal humerus lcpi) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes.ii) plate head should have eight locking screw holes and shaft should have combi holesiii)supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmer v) supplier should be ready to exchange unused plates for required implants vi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steelviii)required sizes:left: 3h,4h, 5h,6h,7h,8h,9h,10h right: 3h,4h,5h,6h,7h,8h,9h,10h , dital humerus medial lcp i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes.ii) plate head should have atleast three locking screw holes and shaft should have combi holesiii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks lastiv) inventory with all screw sizes should be maintained in jipmerv) supplier should be ready to exchange unused plates for required implantsvi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steelviii) required sizes left: 3h,4h,5h,6hright: 3h,4h,5h,6h , dital humerus postero lateral lcpi) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes.ii) plate head should have condylar extension and atleast five locking screw holes and shaft should have combi holesiii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aimingdevice/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmerv) supplier should be ready to exchange unused plates for required implantsvi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steelviii) required sizes left: 3h,4h,5h,6hright: 3h,4h,5h,6h , distal humerus extra articularanatomical locking plate i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes.ii) plate head should be anatomical to posterior contour of lateral condyle, atleast five locking screw holes and shaft should have combi holesiii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) iventory with all screw sizes should be maintained in jipmerv) supplier should be ready to exchange unused plates for required implnatsvi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steel viii) required sizes left: 4h,5h,6hright: 4h,5h,6h , 2.4/2.7/3.5mm proximal ulna locking i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes. ii) plate head should have atleast four locking screw holes and shaft should have combi holesiii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmer v) supplier should be ready to exchange unused plates for required implants vi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steelviii)required sizes 3h,4h,5h , 2.4/2.7 mm dual column distal radius volar locking plate unit:i) unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes.ii) plate head should have atleast eight locking screw holes and shaft should have combi holesiii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks lastiv) inventory with all screw sizes should be maintained in jipmerv) supplier should be ready to exchange unused plates for requiredvi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steel viii)sizes required3h, 4h, 5h , 2.4/3.5 mm lateral end cavicle locking platei)unit: 1 unit consists of plate-1 no. along with appropriate type and number of screws as per the plate holes.ii) plate head should have atleast five locking screw holes and shaft should have combi holes iii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmerv) supplier should be ready to exchange unused plates for required implants vi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steel viii) sizes required left: 3h,4h,5h right: 3h,4h,5h , titanium elastic nail i) supplier should supply the complete set of instruments on loaner basis till stocks last ii) supplier should be ready to exchange unused screws for required sizes , titanium elastic nail2 mm , titanium elastic nail2.5 mm , titanium elastic nail 3 mm , titanium elastic nail 3.5 mm , titanium elastic nail 4 mm , 6.5/7 mm partially threaded/fully threaded cannulated cancellous screws 1. should be made of surgical grade titanium2. screws should be supplied with equal number of compatible washers 3. the complete set of necessary instruments required for screw insertion (including compatible threaded guide wires(10 nos) should be supplied on loaner basis iv) sizes required in increments of 5 mm: 75 mm to 95 mm - 10 each (50) , 100 mm to 120 mm - 15 each (75) , 125mm to 135 mm - 5 each (15) , reconstruction femoral nail1. should be made of surgical grade stainless steel or titanium2. nail should be compatible with antegrade piriform fossa entry 3. proximal nail should have options for recon bolts, descending trochanteric bolts and lateral to medial standard interlocking bolt (2 each)4. distal nail should atleast two locking holes5. the complete set of instrumentation required for nail and locking bolt insertion should be supplied on loaner basis 6. one nail along with all the requisite bolts will be considered as one unit7.prices quoted should be inclusive of screw costs 8. sizes required: 9mm x 38, 40, 42 - 4 units each10mm x 38,40,42 - 8 units 11mm x 38,40,42 - 8 units each , supracondylar nail with blade1. should be made of surgical grade stainless steel or titanium2. nail should be compatible with retrograde intercondylar notch entry 3. proximal nail should have atleat two antero posterior locking holes and distal nail should have at least 3 medio lateral locking holes of which one should accomodate a blade type locking bolt 4. the complete set of instrumentation required for nail and locking bolt insertion should be supplied on loaner basis5. one nail along with all the requisite bolts will be considered as one unit 6. prices quoted should be inclusive of screw costs7. sizes required: 9 mm x 30,32,34 - 5 units each10 mm x 30,32,34,36,38 - 5 units each 11 mm x 30,32,34,36,38 - 5 units each , expert tibial nail for metaphysial - diphysial fractures. i) unit: each tibial interlocking nail unit consist of tibial interlocking nail - 1 no along with appropriate type and number of locking bolts ii)proximal part of nail should have 5 locking options, 3 oblique and 2 medio- lateral.distal part of nail should have 4 locking option in multiple directions (assorted sizes) iii) supplier should be ready to exchange unused implants for required sizesiv) implants should be made of surgical grade stainless steel v) complete instrumentation set should be supplied on loaner basis price should be quoted for complete unit vi) supplier should be ready to exchange unused implants for required sizes vii) sizes required 8,9,10 x 28,30,32,34 - 5 each , 2.4 mm radial head locking lcp i) unit -1 unit consists of anatomical radial head locking plate 1 no along with appropriate type and number of screws as per plate holes ii) plate head should have atleast 5 screw holes and shaft should have combi holesiii) supplier should supply the complete set of instruments including drill bit, tap, depth gauge, threaded drill sleeve, screw driver, aiming device/guiding block on loaner basis till stocks last iv) inventory with all screw sizes should be maintained in jipmer v) supplier should be ready to exchange unused plates for required implantsvi) prices quoted should be inclusive of screw costs vii) implants should be made of surgical grade stainless steelviii)required sizes:2h,3h,4h , general consumables , resuable monopolar cable compitable toalan /shalaya diathermy , resuable bipolar cablecompitable toalan/shalaya diathermy , bipolar forceps straighttip with cable compitable toalan /shalaya diathermy , disposable cautery plate adult compitable to alan /shalaya diathermy , disposable cautery plate paediatric compitable toalan /shalaya diathermy , scratch pad for cautery pencil tip cleaning , diposable and sterileimpervious surgeon gown , transparent povidone iodine impregnated incisional adhesive drape size:60 x 75 cm , disposable and sterile c arm drape [should completely cover the c arm”should have adhesive surfaces or adhesive tapes to fasten to the c arm suitable for simens (sir moblie compact ) and skanray , diposable and sterile trolley impervious drape 150 x100 , diposable and sterile trolley impervious drape 65x62 , diposable and sterile laparatomy drape , diposable and sterile impervious bed sheets83x48 , diposable and sterile impervious bed protector roll with inbetween perforation at every 96 thickness: 70gsm width-48 length-2880 , disposable and sterile transperent blade for tourenvideo laryngoscopeblade size: 1,2,3,4,5 , craniotomy drape central round integrated self adhesive transparent (not just transcluscent) area of diameter greater than 20 cm, with surrounding flange, tubing for drainge of blood and wash fluid, rest of the non-woven material of the drape should be fluid impermeable of dimensions 2x1.6 m. capable of covering the patients’ torso. if the central area is not transparent it will be rejected since it is not according to specification. , laminectomy drape water resistant drape with central iodine impregnated transcluscent adhesive patch which can cover from head to toe for laminectomy , microscope drape transparent thin sterile microscope drape for use withneurosurgical operating microscope and the f40 leica and the drape should fit properly[sample to be provided to assess suitability , ventriculoperitoneal shunt drape for ventricular shunt surgery covering head to abdomen with transparent sticking operation site plastic incise drape , threaded guide pins single ended2mm x 450mm, 2.5mmx 450mm , fore arm distractor , jess fixator set with distractor small , jess fixator set with distractor medium , jess fixator set with distractor large , long monopolar tip , pneumatictourniquet cuff small, medium large compatible to vbm tourniquet machine , colorado microdissectionneedle with flexible shaft , manman cutter blade , manman perforator plunge reusable 12mm , manman perforator plunge reusable 10mm , manman perforator plunge reusable 8mm , stryker fa2 2.3mmtapered router (ref : 5407-fa2-023) , stryker burr round and cutting 1mm to 5mm sizes , stryker acorn burs with a head size of 5.0mm , flowseal 5ml , tissel , 2.0 vicryl suture cutting anti bacterial , 3.0 vicrylsuture cutting anti bacterial , 1 vicryl suture cutting anti bacterial , artificial dural graft non-biological / synthetic, biocompatible, implantable, artificial dural graft. sewable to normal dura. should be impervious to fluid. for permanent implant. should lead to minimal adhesion formation and tissue reaction. expanded polytetrafluoroethylene (eptfe) preferred. , soft nasal pack with breathing hole after endoscopic nasal surgery (polyvinylalcohol material) , soft nasal pack without breathing hole after endoscopic nasal surgery (polyvinylalcohol material) , neurosurgical patties sterile, ready to use cotton patties, in sterile packaging. size7x2 cm, each pack should contain at least 10 patties , softroll cotton, softroll cotton of size 10x3m [need not be sterile] , perforator with plunge guard (single use, disposable) perforator with inherent mechanism to stop a plunge once dura is reached. should be compatible with hudsons brace available in jipmer , ventriculoperitoneal shunt [medium pressure, adult size] burr hole design of chamber and valve with diaphragm type valve. chamber should sit on the burr hole which allows aspiration of csf if required. biocompatible material. the part that is placed on the burr hole should have a low profile (very important). valve seating interface of dissimilar polymers. , ventriculoperitoneal shunt [medium pressure, pediatric size] burr hole design of chamber and valve with diaphragm type valve. chamber should sit on the burr hole which allows aspiration of csf if required. biocompatible material. medium opening pressure. pediatric size. . the part that is placed on burr hole should have a low profile(very important). valve seating interface of dissimilar polymers , ventriculoperitoneal shunt [low pressure, adult size] burr hole design of chamber and valve with diaphragm type valve. chamber should sit on the burr hole which allows aspiration of csf if required. biocompatible material. the part that is placed on the burr hole should have a low profile (very important). valve seating interface of dissimilar polymers , ventriculoperitoneal shunt [high pressure, adult size] burr hole design of chamber and valve with diaphragm type valve. chamber should sit on the burr hole which allows aspiration of csf if required. biocompatible material. medium opening pressure. adult size. the part that is placed on the burrhole should have a low profile (very important). valve seating interface of dissimilar polymers (will be rejected if it is not a burr hole design or if the chamber is not low profile) , external ventricular drainage system which should include ventricular catheter, connecting tubes, leak proof drainage bag with volume markings and built in csf pressure scale {in a sterile and ready to use pack.} , fibrin sealant/glue - glue for use in neurosurgery to prevent csf lead based on fibrin coagulum formed on mixing fibrinogen and thrombin components in easy to apply chamber and nozzle system. dual tip syringe system and vials with sterile water for reconstitution should be part of the package. total quantity should be at least 1 ml after generation of fibrin. warming and stirring device should be made available in ot or on demand within 24 hours. components, if derived from pooled or single donor human blood should be free from all known pathogens. (any agitating/warming device required to mix the glue should be provided during use and kept in neurosurgery ot) , lumbar puncture needle single use disposable lumbar puncture needles-sizes 18g size only , hemostatic activated regenerated cellulose for intraoperative hemostasis in fibrillar form , absorbable gelatin foam sterile ready to use gelatin foam in tear away package for use as haemostatic agent in neurosurgery. , injectable hemostatic agent prefilled syringe with haemostatic matrix agent for intraoperative use. , bone flap fixation system for fixing bone flap using titanium or similar biocompatible material with thin profile, preferably with compressing plates on both sides of burr hole. quote for one clamp 11-16 mm. all instruments on loan basis. , bipolar forceps bayoneted (standard tip non stick, microtip non stick, standard tip and micro tip) compatible with excel bipolar machine along with cable( demo required) , bipolar forceps bayoneted with irrigation channel (standard tip non stick, microtip non stick, standard tip and micro tip) compatible with mallis bipolar machine along with cable (demo required) , bipolar forceps bayoneted standard tip non stick compatible with alan/ shalya bipolar machine along with cable (demo required) , bipolar forceps bayoneted microtip non stick, compatible with alan/ shalya bipolar machine along with cable (demo required) , bipolar forceps bayoneted standard tip compatible withalan/ shalya bipolar machine along with cable (demo required) , miniplate and screw system for fixing bone flap and during craniofacial surgery. 24 hole plate (profile height 0.8 mm) with 10 self drilling screws (2.0 x 4 mm) , one emergency screw (2.3 mm x 6 mm)(self drilling nature and the ease of application to be demonstrated). each colour coded) , non consumable items , adson non toothed forceps 4 , adson self retaining retractor, 320mm, 12 3/4 , anastamotic needle holder , a-o type pointed reduction clapms (small/med/large) , a-o type serrated bone holding clamps(small/med/large) , artery forceps long curved , artery forceps medium curved , artery forceps, curved,mosquito , balfour retreactor , ball spike , bayoneted macro forceps, straight, 21cm, 0.5mm tip , bayoneted micro forceps, straight, 21 cm, 0.5 mm tip , beckman eaton self retaining retractor, 320mm, 12 3/4 , bonepunch horse shoe curved , bonepunch horse shoe stright , bone cutter medium , bone cutter small , bone file 150 mm , bone graft punches large 254 mm, head dia 12x18mm straight & angled , bone graft punches small 254 mm, head dia 9x15mm straight & angled , bone hook , bone impactor , bone tap 3.5mm , 4.5mm , box spanner t type 10 size , box spanner t type 11 size , brain cannula brain cannula [ventriculostomy cannula] with opening in the tip with obturator [stylet] , brain retractor (malleable) , bristo periostal elevator , bull dog clamps micro , bull dog curved , caspar 360 degree rotatable pituitary scissors , casper retractor , cheatle forceps , clamp holder 6 , cloward retractor with 5 pairs blades of different sizes , cobbs elevator all sizes ( each 5nos) , counter sink (3.5mm, 4.5mm, 5mm, 6mm ) , cross action towel clips , debakey’s forceps 4” , debakey’s forceps 6” , debakey’s forceps 8” , dural guide , echlin bone rongeur, 230mm, 9 , echlin bone rongeur, 230mm, 9 , f- tool made of carbide( radio lucent) large & medium , feet protection gear for surgeon and scrub nurses with anti slippage technology. (surgeon’s shoes) (pairs) washable, with side holes, comfortable to wear ( three sizes, preferably blue or green colour) . should not be rubber or plastic but be made of closed cell resin material which should have antibacterial properties and odor free. the top should be of strenghthened material to prevent injuries due to falling sharp instruments. please label jipmer, neurosurgery on top and sides of shoes if possible with wash resistant paint or embossing. , fine cats paw retractor , fine cross clamp 4” , fine suction nozzle [ size 3] , fine suction nozzle [ size 4] , fine suction nozzle [ size 5] , fine tip right angled double action nibbler medium size , finochette retractor [adult] , finochette retractor [paediatric] , fish hooks with spring to retract scalp flap during craniotomy , flexible reamer detachable type shaft with tips of 8mm to 13mm size( 0.5mm difference) , forceps jar , freer periosteal elevator, 185mm, 7 1/4, sharp & blunt , frykhon bone rongeur, 240mm, 9 1/2 , frykhon bone rongeur, 240mm, 9 1/2 , gardner - wells skull tongs along with traction pulley and 10kg weights (1kg - 6 nos., 2kg - 2 numbers) the skull tongs should have spring loaded pins.adult -2nospaediatric-2nos , gelpie retractor small, medium, large , gigli saw handle ( set of 2nos ) , guide pin (1.0,1.2,1.5,1.8) x 20 cms, 2.0 mm x 30 cm , guide wire aiming and repositioning devicei) should allow 5 degree angulation and 5 mm offset insertion ii). should accommodate guide wires upto 3.2 mm , hair clipping machine that can be sterilized or capable of using sterile disposable (or resterilisable) blade head. the system should be chargeable and usable without cord. should be fda approved. handle should be water proof and can be disinfected. should be capable of atleast 40 minutes of use after charging. (100 clipper heads to be provided along with machine). should be able to remove scalp hair easily. , hand drill with chuck key , hardy pituitary speculum (adult) , hardy pituitary speculum (pediatric) , higgs retractor , hinterman retractor - large , hinterman retractor - small , howath dissector , hudson brace full set (perforator, burr points and attachments) , humbys knife handle , hunt bayoneted tumor holding forceps, 20 cm, 3 mm tip & 2mm tip , jansen self retaining retractor, 100mm, 4 , jansen self retaining retractor, 100mm, 4 , jewellers forceps curved4 , kerrison bone bunche 1mm 130 degree forward up cut and down cut , kerrison bone bunche 2mm 130 degree forward up cut and down cut , kerrison bone bunche 3mm 130 degree forward up cut and down cut , kerrison bone bunche 4mm 130 degree forward up cut and down cut , killians nasal speculum (adult) , killians nasal speculum (pediatric) , knifehandle no-3 , knifehandle no-7 , laminectomy self retaining retractor , langenbeck-bone-elevator-23cm-10mm-blunt-strong-curve , langenberg retractor , lexer osteotome, 220mm, 8 3/4 , luer - stille bone rongeur, 225mm, 9 , luer - stille bone rongeur, 225mm, 9 , lumbar self retaining retractor big size , malleable retractor 15x 1cm , mallot big , mallot small , mastoid retractor with flexible , mayfield bone rongeur, 175mm, 7 , mayfield pediatric horse shoe headrest- vertical and lateral adjustments, adjustable pad base, fluid resistant gel pads. , mayfield swivel horse shoe head rest adult- vertical and lateraladjustments, adjustable pad base, fluid resistant gel pads, pulley rod attachment for skeletal traction. , mayo scissors straight 8 , mc donald dissector , medzenbalm curved scissor 8 , medzenbalm scissors 8” inch curved , medzenbalm scissors 8” inch straight , metal scale 30cms with nail diameter measuring gauge , metzenbaum scissors, 180mm, 7 (straight & curved) , micro disc punches, ceramic coated, straight & angled , micro dissector 4 , micro dissector, plate - shaped, 230mm, 9 , micro dissectors ball hook type , micro dissectors pointed type , micro dissectors sickle type , micro forceps toothed 6 , micro forceps with round handle and counter balance, 210mm, 8 1/4 , micro scissors [curved] 4 , micro scissors [straight] 6 , micro suction regulator should be attached with suction tube and to be controlled by the surgeon , micro suture tying forceps with round handle and plateau at the tips, 180mm, 7, 0.5mm tip , micro-adsons toothed forceps, 180mm, 7 , microball probes, 90 degree & 45 degree , mollisons mastoid retractor medium size , morrios reteratot medium size , mosquito artery forceps curved 4 , mosquito artery forceps straightv 4 , needle holder 10 , needle holder 8 , needle holder castroveijo 6 , needle holder rider 6 , nerve hook 90 degrees , nerve hook retractor8 , nicola malleable pituitary curette , open double end spanner 10/11 size , open double end spanner 8/9 size , osteotomes straight and curved all sizes , pellvic reduction instrumentation compelete set , pelvic reduction clamps (small, medium, large) , perforator with plunge guard (reusable, sterilizable) perforator with inherent mechanism to stop a plunge once dura is reached. should be compatible with hudsons brace available in jipmer, otherwise brace to be provided free of cost. , periosteal elevator - parabeuf6inch ,10inch , periosteal elevator - parabeufforearm , periosteal elevator [bristo ] , periosteal elevator small with woooden handle , peritoneal trocar , perneczky micro scissors, 130mm, 5 1/8, straight cutting , pliers , pointed reduction clamps [big ] , pointed reduction clamps [medium] , pointed reduction clamps [small ] , potts scissor 8 , raney clip applicator 6 , regular disc punches, ceramic coated, straight & angled , renolds scissor 4 , renolds scissor 5 , renolds scissor 6 , reverse potts scissor 8 , rhoton micro dissector set , right angle clamp (fine tip) , rod cutter medium to cut 2mm to 4mm rods , rod cutter zimmerto cut rods of 4mm to 6mm , scoville self retaining retractor with 5 pair blades , screw drivers cannulated 3.5 , screw drivers cannulated 6.5 , self retaining retractor medium size , shunt tunneller, adult , shunt tunneller, peadiatric , silicon gel bolster lxwxh 380mmx150mmx120mm , solid screw driver 3.5mm, 4.5mm , sponge holder , sponge holding forceps , ss wire twister , stille periosteal elevator, 205mm, 8 , suction regulator , suture tying forceps 6 , tenotomy scissor 4 curved , tenotomy scissor 6 curved , tetra towel clips , thumb forceps toothed , tongue depressor , tray ss with lip and smoth edges size: 20x16x7.5inch , universal‘t’handle (should have been designed to hold drill bits or schanz pins of upto 10mm diameter and should be cannulated) , universal t handle with keyless chuck , vertebral spreader , vessel dilator , volkmans double ended currete 10 inch , weitlander self retaining retractor, 165mm, 6 1/2 , wire puller , wire twister , wooden handle scoop 2, 4, 5, 6, 8, 10, 12 mm , yankauers suction nozzle , yasargil micro needle holder, 200mm, 8 , yasargil micro scissors, 150mm, 6, non glare finish. dot matrix code, din, en, iso certified, imported stainless steel. sharp tip & blunt tip , yasargil micro scissors, 185mm, 7 1/4 straight, spring type with flat serrated handle. dot matrix code, din, en, iso certified, imported stainless steel. sharp tip & blunt tip , yasargil micro scissors, 225mm, 9 - upwards curved tip , yasargil micro scissors, straight tip , minor equipmnents , 55 andorid led 4k medial monitor with hdmi & vga port , x ray radiation protection two piece lead apron skirt shirt (light weight)with appropriate hanging standspecifications: lead free radiation protection armor: light weight, lead free material without compromising on protection. should be wrap around and with shoulder padding with adjustable belts around waist , x ray radiation protection gonad shield adult + pead , x ray radiation protection thyroid shield adult , ss surgeon chair with hand rest , intra operative ultrasound , day-bailes tapered locking suction tube system (please do not exceed rs 50,000) balanced handpiece (flat teardrop suction handle with safety coupling and day suction tube handle w/safety coupling) which can be kept between thumb and forefinger space for a attaching a range of suction cannulasbalanced handpiece (flat teardrop suction handle with safety couplingcannulas are of the following sizes (3 to 12 french, each in following lengths - short: 7.6 cm medium: 9.5 cm long: 11.4 cm extra long: 13.3 cm. also multihole tube type each 5, 7 and 9 french (all suction cannulas [43 numbers] should preferably come in its own case). the suction cannulas have to be pre-bent 30 degrees, malleable and rotatable and ability to change tube without discarding hand piece , continuous band sealerhorizontal sealing model specification : 1. fully made of ss 304 body2.warrnaty for 3years 3. additional teflon belt -50nos 4. additional nylon belt -10nos 5. digital thermostat with emergency power switch