tender for repairs of savitribai fule prasutigrah at shingnapur tal man- 1 removing doors and windows with frames and stacking the materials as directed with all leads, lifts excetra complete.item / page no : 15 / 296additional specifications : the work shall be carried out as directed by engineer-in-charge. 2 providing and laying cast in situ/ready mix, cement concrete in m-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailling out water, formwork, laying/ pumping, compacting and curing, excetra complete, with fully automatic micro processor based programmable logic controller without supervisory control and data aquisition enabled reversible drum type mixer/ concrete batch mix plant (pan mixer) excetra complete. with fine aggregate (natural sand / crushed sand vsi grade finely washed, excetra) (using artificial sand).item / page no : 1 / 175specification no : bd.e.1spec. page no : 287-288additional specifications : 1. with additional specifications for controlled concrete. 2. if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 3 removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts excetra complete.item / page no : 19 / 297additional specifications : the work shall be carried out as directed by engineer-in-charge. 4 providing second class burnt brick masonry with conventional / indian standard type bricks in cement mortar 1:6 in foundations and plinth of inner walls / in plinth of external walls including bailling out water manually, striking joints, on unexposed faces, racking out joints on exposed faces and watering, excetra complete. (using artificial sand).item / page no : 1 / 197specification no : bd.g.1spec. page no : 313additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 5 providing second class burnt brick masonry with conventional / indian standard type bricks in cement mortar 1:6 superstructure including striking joints, racking out joints, watering and scaffolding, excetra complete. (for ground floor) (using artificial sand).item / page no : 5 / 197specification no : bd.g.5spec. page no : 315additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 6 providing and fixing in position (as per indian standard : 1868/1982) aluminium sliding window of two tracks with rectangular pipe having overall dimentsions 63.50 milimetre x 38.10 milimetre x 1.02 milimetre at weight 0.547 kilogram per running metre and window frame bottom track section 61.85 milimetre x 31.75 milimetre x 1.20 milimetre at weight 0.695 kilogram per running metre. top and side track section 61.85 milimetre x 31.75 milimetre x 1.30 milimetre at weight 0.659 kilogram per running metre. the shutter should be of bearing bottom 40 milimetre x 18 milimetre x 1.25 milimetre at weight 0.417 kilogram per running metre. interlocking secion 40 milimetre x 18 milimetre x 1.10 milimetre at weight 0.469 kilogram per running metre and handle section 40 milimetre x 18 milimetre x 1.25 milimetre at weight 0.417 kilogram per running metre and top section 40 milimetre x 18 milimetre x 1.25 milimetre at weight 0.417 kilogram per running metre as per detailed drawing and as directed by engineer in-charge with all necessary aluminium sections, fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 milimetre thick plain glass with all required screws and nuts excetra complete. - with powder coating without box. (for ground floor)item / page no : 40 / 252additional specifications : the work shall be done as per instructions of engineer in charge. 7 providing and fixing mild steel grill work for windows, ventilator, excetra 20 kilogram per square metre as per drawings including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting, excetra complete. (for ground floor)item / page no : 1 / 264specification no : bd.u.1spec. page no : 537 8 providing internal cement plaster 20 milimetre thick in single coat in cement mortar 1:5 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing, excetra complete. (for ground floor) (using artificial sand).item / page no : 6 / 209specification no : bd.l.4spec. page no : 368additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 9 providing and laying ceramic tiles of having sizes 30 centimetre x 30 centimetre and confirming to corrosponding indian standared for dado and skirting in required position with ready made adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white / colour cement slurry, cleanding, curing, excetra complete. (for ground floor) (using artificial sand).item / page no : 25 / 215specification no : bd.m.13spec. page no : 386additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 10 providing and fixing white glazed earthenware wash hand basin of 45 centimetre x 30 centimetre size including cold water piller tap / cold and hot water piller tap brackts, rubber plugs and brass chain, stop tap and necessary pipe connections including polyvinyl chloride waste pipe and trap upto the outside face of the wall.making good thedamaged surface, testing excetra complete. (for ground floor)item / page no : 64 / 272specification no : bd.v.30spec. page no : 565 11 providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shed having telephonic black / colour granite of 18 milimetre thick fixed on black kadapaa frame work, including cromium plated coupling, bottle-trap using approved make oval type wash basin as per detailed drawing or as directed by engineer in-charge, excetra complete. (for ground floor)item / page no : 88 / 283additional specifications : the work shall be carried out as per instructions of engineer in charge. 12 providing, laying and fixing polyvinyl chloride pipe of 110 milimetre diameter with fittings such as bends, tees, reducers, clamps, excetra including necessary excavation, trench filling, excetra complete.including removing existing pipe line if necessary and conveying and stacking thesame in pwd chowky or as directed excetra complete.item / page no : 28 / 277additional specifications : the work shall be done as per instructions of engineer in charge. 13 providing and fixing screw down 15 milimetre diameter wheeled stop tap of brass including necessary sockets / union nut complete. (for ground floor)item / page no : 43 / 270specification no : bd.v.9spec. page no : 555 14 providing and applying interior wall finish luster of approved make on internal wall surface as detailed below scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10 percent and oil 15 to 20 percent with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. scrapping with emery paper 180 and wipe clean. applying wall primer with brush with mineral turpentine 8 to 10 percent and oil 15 to 20 percent with roller. scrapping emery paper 320 and wipe clean, interior wall finish luster first coat with brush/ rubber/ spray with mineral turpentine 7 to 9 percent and oil with roller 19 to 21 percent. after 8 hours of activity, applying second coat or wall finish lustre with mineral turpentine 7 to 9 percent with brush and oil with roller 19 to 21 percent after allowing dry for the period of 6 to 8 hours activity. (with prior approval of s.e.) (for ground floor)item / page no : 20 / 228additional specifications : the work shall be done as per instructions of engineer in charge. 15 providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding indian standard of approved manufacturer and of approved colour to the plastered surfaces including cleaning, preparing the plaster surfaces, applying primer coat, scaffolding, if necessary and watering the surface for two days, excetra complete. (for ground floor)item / page no : 25 / 225additional specifications : the work shall be carried out as per instructions of engineer in charge. 16 providing and fixing chromium plated sink cock with raised j shaped swinging casted spout of approved make including necessary sockets / union nut, excetra complete. (for ground floor)item / page no : 84 / 283additional specifications : the work shall be carried out as per instructions of engineer in charge. 17 providing and fixing 450 milimetre x 550 milimetre size superior type belgium mirror with 16 milimetre diameter nickel plated towel rod, excetra complete. (for ground floor)item / page no : 20 / 276additional specifications : the work shall be done as per instructions of engineer in charge. 18 providing and fixing on walls / celling / floor, 40 milimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings, remaking good the demolished portion, excetra complete.including removing existing pipe line if necessary and conveying and stacking the same in pwd chowky or as directed excetra complete. (for ground floor)item / page no : 59 / 280specification no : bd.v.5spec. page no : 551additional specifications : the work shall be done as per instructions of engineer in charge. 19 providing and fixing on walls / celling / floor, 50 milimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings, remaking good the demolished portion, excetra complete. (for ground floor)item / page no : 60 / 280specification no : bd.v.5spec. page no : 551additional specifications : the work shall be done as per instructions of engineer in charge. 20 providing and fixing on walls / celling / floor, 25 milimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings, remaking good the demolished portion, excetra complete.including removing existing pipe line if necessary and conveying and stacking the same in pwd chowky or as directed excetra complete. (for ground floor)item / page no : 57 / 280specification no : bd.v.5spec. page no : 551additional specifications : the work shall be done as per instructions of engineer in charge. 21 providing and fixing screw down for 50 milimetre diameter wheeled stop tap of brass including necessary sockets / union nut complete. (for ground floor)item / page no : 48 / 270specification no : bd.v.9spec. page no : 555 22 providing and fixing screw down for 40 milimetre diameter wheeled stop tap of brass including necessary sockets / union nut complete. (for ground floor)item / page no : 47 / 270specification no : bd.v.9spec. page no : 555 23 providing and fixing screw down for 25 milimetre diameter wheeled stop tap of brass including necessary sockets / union nut complete. (for ground floor)item / page no : 45 / 270specification no : bd.v.9spec. page no : 555 24 providing and constructing brick masonry inspection chamber 60 centimetre x 45 centimetre x 90 centimetre including 1:4:8 cement concrete foundation, 1:2:4 cement concrete channels, half round glazed stoneware pipes, brick masonary, plastering from inside and farme fixed in cement concrete cover medium duty 140 kilogram with frame excetra complete. (using artificial sand).item / page no : 12 / 275specification no : bd.v.43spec. page no : 574additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 25 2.providing and fixing heavy duty inter locking concrete rubber mould glossy paving blocks of 60 milimetre thickness of having a strength of 400 kilogram per square centimetre of approved quality and shape on a bed of crushed sand of 25 milimetre to 30 milimetre thick including striking joints and cleaning excetra complete.(using 100 per cent crushed sand), excetra complete.item / page no : 53 / 219specification no : bd.m-12spec. page no : 385additional specifications : the work shall be carried out as per instructions of engineer in charge. 26 providing and laying cast in situ / ready mix cement concrete m-20 of trap / granite /quartzite/ gneiss metal for reinforced cement concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks,laying/pumping, compaction and roughening the surface if special finish is to be provided and curing complete. (excluding reinforcement and structural steel). with fully automatic micro processor based programmable logic controller without supervisory control and data aquisition enabled reversible drum type mixer/ concrete batch mix plant (pan mixer) excetra complete. with fine aggregate (natural sand / crushed sand vsi grade finely washed etc) (for ground floor) (using artificial sand).item / page no : 50 / 181specification no : bd.f.6, b-7spec. page no : 300-301, 38-40additional specifications : 1. with additional specifications for controlled concrete. 2. if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 27 clean the existing surface / terrace thoroughly to remove dirt, loose particles, laitance, excetra. for emergency waterproofing of existing terrace. use a vacuum cleaner or high pressure jet or wire brushing as per requirement. examine the surface closely for any cracks. fill it with acrylic polymeric non-shrink crack filler putty as approved by engineer in charge a pure aliphatic, acrylic, polymer modified ready to use paste. after filling, allow the surface to dry for atleast 24 hours. if the depth of the crack is more than two milimetre to three milimetre apply in layers at intervals. moisten the surface with a water jet one day prior to the application of waterproofing coating. mix one part of 2-(methoxycarbonyl)- 1-propene-butyl- two propenoate (mpbp) membrane as approved by engineer in-charge and one part of grey cement by weight using a low speed mechanical stirrer to form slurry lump free consistency. apply this as a primer coat of 2- (methoxycarbonyl)- 1-propene-butyl- 2propenoate (mpbp) membrane as approved by engineer in charge. apply the same slurry by roller at 24 hours interval between the applications of each coat. extend the coating to parapet walls. allow the primer coat to set for 24 hours. after the primer coat is set, apply two coats of pure enoate based polymer titanium dioxide based 2-(methoxycarbonyl)- 1-propene-butyl- two propenoate (tmpbp) and 2- (methoxycarbonyl)- 1-propene-butyl- two propenoate (mpbp) of waterproof coating as approved by engineer in-charge on surface. ensure that no pinholes are let untouched. allow the membrane to cure for 24 to 48 hours. single component, ultra violet resistant, elastomeric, high build waterproof coating (confirming to din 1048) should have following minimum properties:(1) elongation percent (astm d 638): at the rate of 400percent (2) tensile strength (astm d 412): 150 pounds per inch (3) water permeability (din 1048): zero (4) solids: > 65 percent (5) ph: 8.5 - 10.5item / page no : 25 / 434additional specifications : the work shall be done as per instructions of engineer in charge. 28 providing soak pit of size 120 centimetre x 120 centimetre x 120 centimetre including excavating and filling with brick bats.item / page no : 19 / 275specification no : bd.v.46spec. page no : 576 29 dismantling brick masonry in lime or cement mortar and stacking the materials as directed with all leads, lifts excetra complete.item / page no : 9 / 296additional specifications : the work shall be carried out as directed by engineer-in-charge. 30 providing and laying vitrified matt finish tiles of having size 590 milimetre to 605 milimetre x to 605 milimetre of 8 milimetre to 10 milimetre thickness and confirming to indian standard 15622-2006 (group bia) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning, excetra complete. (for ground floor) (using artificial sand).item / page no : 42 / 217specification no : bd.m.12spec. page no : 385additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 31 providing and laying vitrified matt finish tiles having size 590 milimetre to 605 milimetre x to 605 milimetre of 8 milimetre to 10 milimetre thickness and confirming to indian standard 15622-2006 (group bia) of approved make, shade and pattern for dado and skirting in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning, excetra complete. (for ground floor) (using artificial sand).item / page no : 43 / 217specification no : bd.m.12spec. page no : 385additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 32 providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 milimetre to 605 milimetre x 590 milimetre to 605 milimetre of 8 milimetre to 10 milimetre thickness and confirming to indian standard 15622-2006 (group bia) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning, excetra complete. (for ground floor) (using artificial sand).item / page no : 40 / 217specification no : bd.m.12spec. page no : 385additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 33 providing and laying vitrified mirror / glossy finish tiles having size 590 milimetre to 605 milimetre x 590 milimetre to 605 milimetre of 8 milimetre to 10 milimetre thickness and confirming to indian standard 15622-2006 (group bia) of approved make, shade and pattern for dado and skirting in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning, excetra complete. (for ground floor) (using artificial sand).item / page no : 41 / 217specification no : bd.m.12spec. page no : 385additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 34 provoding and fixing high density polyethylen container one piece moulded water tank made out of high density polyethylen and built corrugated inclusive of delivery upto destination housting, fixing of accessaries such as inlet, outlet, overflow pipe inclusive of all taxes. capacity between 200 litres to 1000 litres. (for ground floor)item / page no : 53 / 280additional specifications : the work shall be done as per instructions of engineer in charge. 35 providing and fixing machine cut machine polished 18 milimetre to 20 milimetre thick telephone black / amba white / cadbury brown / rbi red / ocean brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on a bed of 1:4 cement mortar including float, filling joints with neat cement slurry, curing, polishing and cleaning, excetra complete. (for ground floor) (using artificial sand).item / page no : 35 / 216specification no : bd.m.22 bspec. page no : 390additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 36 providing and laying rough shahabad stone flooring 25 milimetre to 30 milimetre thick and of required width in plain / diamond pattern on a bed of 1:6 cement mortar including cement float, striking joints, pointing in cement mortar 1:3, curing and cleaning, excetra complete. (for ground floor) (using artificial sand).item / page no : 1 / 213specification no : bd.m.1spec. page no : 379additional specifications : if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 37 providing and fixing frame with / without ventilator of size as specified with non teak wood for doors and windows including chamfering, rounding, rebating holdfast of size 300 milimetre x 40 milimetre x 5 milimetre with oil painting, excetra complete. (for ground floor)item / page no : 2 / 245additional specifications : the work shall be done as per instructions of engineer in charge. 38 providing and fixing single or double leaf panelled door shutter excluding frame with glazed openable fanlight shutter 35 milimetre thick as per detailed drawing consisting of panelled vertical styles 100 milimetre x 35 milimetre and lock and bottom rail 200 milimetre x 35 milimetre and panels 12 milimetre thick both side commercial ply faced partical board, including stainless steel fixtures and fastening and teak wood beading at junctions of panel insert and as instructed by the engineer in charge including three coats of oil painting, excetra complete. (for ground floor)item / page no : 7 / 246additional specifications : the work shall be done as per instructions of engineer in charge. 39 providing and fixing mild steel grill gate with angle iron frame 65 milimetre x 65 milimetre x 10 milimetre with iron bars at 150 milimetre center to center and diagonal flats as per the detailed drawing including hinges, pivot blocks locking arrangement, welding riveting and oil painting of three coats of approved shade. weight of gate 35 kilogram per square meter. (for ground floor)item / page no : 10 / 294specification no : bd.w.6spec. page no : 585additional specifications : the work shall be done as per instructions of engineer in charge. 40 providing and applying white wash in two coats on old / new plastered or masonry surfaces and asbetos cement sheets including scaffolding and preparing the surface by brushing and brooming down, excetra complete. (for ground floor)item / page no : 3 / 227specification no : bd.p.1spec. page no : 411 41 providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 milimetre x 38 milimetre x 1.22 milimetre box type, 5 milimetre thick sheet glass louvers of approved quality, excetra complete. (for ground floor)item / page no : 68 / 259additional specifications : the work shall be done as per instructions of engineer in charge. 42 providing and fixing mild steel grill railing weighing 15 kilogram per square metre with teak wood hand rail of size 75 milimetre x 60 milimetre and sill 75 milimetre x 25 milimetre and posts for verandah including fabricating, fixtures, erecting and painting the grill work with one coat of anticorrosive paint and two coats of oil paint and polishing the hand rail with french polish. (for ground floor)item / page no : 9 / 265additional specifications : the work shall be carried out as directed by engineer-in-charge. 43 providing and fixing solid core flush door shutter in double leaf 32 milimetre thick decorative type of exterior grade as per detailed drawings approved face veneers 3 milimetre thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides and finishing with french polish, excetra complete (for ground floor)item / page no : 95 / 263additional specifications : the work shall be carried out as directed by engineer-in-charge. 44 providing and applying two coats of lead / zinc base oil paint / bituminious paint of approved colour to new structural steel work and iron work in buildings including scaffolding if necessary, cleaning and preparing the surface, excetra complete. (excluding primer coat). (for ground floor)item / page no : 4 / 223specification no : bd.o.3spec. page no : 404 45 excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metre and spreading for embankment or stacking as directed. by mechanical means.item / page no : 11 / 23specification no : morth-301spec. page no : 45-53 46 providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification inciuding spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening / binding material to fill the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. - by mechanical means - grading i using screening type-a (13.2 milimetre aggregate)item / page no : 18 / 29specification no : morth-401, 402, 404, 902, 112spec. page no : 109-111, 112-116, 121-129, 417-421, 19-21 47 providing and laying in situ cement concrete m-20 with tremix treatment for 100 milimetre thickness for flooring with groove cutting of 4 milimetre wide 20 milimetre deep with necessary refilling with bitumen, excetra complete. (using artificial sand).item / page no : 30 / 216additional specifications : 1. with additional specifications for controlled concrete. 2. if artificial / vsi crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in circular by chief engineer, public works region, pune bearing no cep/d-2/buildings-2/5940/2017 dated 17/10/2017 and annexure-i attached to it and also circular by chief engineer, public works region, nagpur bearing no 36 dated 15/01/2019 and annexure-i attached to it will be appicable. 48 supplying hard murum / kankar at the road site, including conveying and stacking, excetra complete.item / page no : 29a / 25specification no : morth-408spec. page no : 139-142 49 spreading hard murum / soft murrum / gravel or kankar for side width, excetra complete.item / page no : 30 / 25specification no : morth-408spec. page no : 139-142 50 royalty charges for various building construction bonafied materials which are used for government bonafied works and for which royalty charges are to be paid by the contractor. (this item is to be paid to the contractor only after he pays the royalty amount to revenue department and produces the required voucher.)item / page no : 3 / 0additional specifications : 1. government of maharashtra, revenue and forest department gazette number 146 dated 04/06/2021 and government of maharashtra public works department state schedule of rates 2021-22 general note number a(v), page 5. 2. the amount of royalty charges will be paid only after submission of the receipt in original from revenue authority for payment of royalty to government, stating the name of work. 3. above / below percentage quoted by the contractor will not be applicable for this item. 51 laboratory testing charges for various materials required for items of work, on the basis of testing frequency and charges fixed by vigilence and quality control circle, pune.item / page no : 4 / 0additional specifications : 1. the amount of laboratory testing charges will be paid to contractor only after submission of the original receipt from the vigillence and quality control office with the name of work mensioned on it. 2. above / below percentage quoted by the contractor will not be applicable for this item. 52 providing and fixing road junction / information sign board of size 0.90 metre x 0.60 metre prepared on 16 gauge mild steel sheet with angle iron frame of size 35 milimetre x 35 milimetre x 5 milimetre including painting with one coat of zinc cromate stoving primer and two coats each of green/ white back ground and back side gray stove enamelled, bonded with red retro-reflective sheet engineering grade, border / letters / numeral / arrows, coated with non pealable crystal clear protective coat retaining 100 percent reflection including two angle iron post of size 50 milimetre x 50 milimetre x 5 milimetre of 3.65 metre long inflated at bottom drilled on top and painted in white and black bands of 30 centimetre. with 4 numbers high strength galvanised iron bolts and nuts of size 10 milimetre diameter and 20 milimetre long sheet and angle iron post in one piece without joints including all taxes, conveying, fixing in ground with cement concrete 1:4:8 block of 60 centimetre x 60 centimetre x 75 centimetre size as directed by engineer-in-charge, excetra complete. mild steel board with engineering grade.item / page no : 47 / 64specification no : morth-801spec. page no : ---additional specifications : the work shall be carried out as per instructions of engineer in charge. please enable macros to view boq information