repairs of 25 hp, 75 hp , 100 hp pump motor repairs and valve repairing for mc dharmabad , i)repairs of 100 hp vertical pump set , bowl assembly s.s. shaft 410 , bowl assembly gum metal impellers , neck ring gun metal impeller , providing and fixing bowl assembly gun metal bush , bowl assembly rubber bush , line shaft en.8 , s.s. slues , line shaft coupling , gun metal spider , spider rubber bush , bowl assembly bolt t.v.s. , casing pipe nut bolt , rubber seat , t.t. plate , gland nut , rewinding 100 hp motor , motor bearing 6316 , motor bearing 29324 , transportation arrangement of v.t. pump set for site to work shop and back , removing of 100 hp pump set for repairs from jack well , disassembling of v.t. pump set in work shop , errection of v.t. pump set on jack well after repairs and giving test and trial on load , errection of 100 hp motor opening & fitting , bowl assembly new impeller bronze , 100 hp motor opening & fitting , ii) 100 hp ats ( auto transformer) , contactor 225 a. delta , contactor150 a. star , single phase preventer , timer , ats rewinding 100hp motor , contactor 415 mcb panel board , starter contactor 225 , starter contactor 150 , starter contactor 125 , engine oil , kitkat 200 amp , 100 hp terminal plate , n.o.c. , relay 100hp , copper luggs 90 mm , copper luggs 70 mm , copper luggs 50 mm , copper fuse wire , 100 hp contactor 225 , 100 hp contactor 150 , 100 hp contactor 125 , 200 mcb , 150 mcb , 125 mcb , copper wire 30mm , copper wire 20mm , copper wire 10mm , brass nut bolt 12 mm , brass nut bolt 10 mm , no. nc ( mnx ) , bus bar copper patty , bus bar holder , over load relay , transformer oil , indicator , push bottom on-off , sensor rod , volt meter 4” , ampere meter 4” 0 to 150 amp , p.t. coil , c.t. coil , emergency stop , controlling wiring , power wiring for 200 amp , iii) repairs of 75 hp vt ( oil lubricating) pump set , 75 hp motor opening and fitting , providing and fixing g.m. screw bearing as per sample with oil grove , providing and fixing g.m. bearing big size as per sample , providing and fixing t.t. plate as per sample , providing and fixing t.t. plate bushes as per sample , line shaft cleaning throwing on lathe machine , 50mm dia tube cleaning throwing in work shop , providing and fixing rubber spider/ture supported 200mm dia , providing and fixing tvs not bolts for cloning assembly , providing and fixing rubber packing/flange rubber joints , providing and fixing s.s. shaft couplings as per sample , removing of 75 hp vt pump set for repairs form jack well ( lb-7-p-87 ) , disassembling of v.t. pump set/bowl assembly in work shop for repairs ( lb-7-p-87 ) , providing and fixing impeller neck ring as per sample , providing and fixing bowl assembly g.m. bushes as per sample , providing and fixing bowl assembly rubber bushes , providing and fixing bowl assembly upper and lower bushes , providing and fixing of impeller shaft of size s.s. 410 as per sample , providing and fixing en 8 top shaft of size as per sample , providing fixing line shaft en 8 new 38mm dia 5 feet , assembly of bowl assembly/pump in work shop , errection of vt pump set/moor on jack well after repairs and giving test trial on load , making transportation arrangement of vt pump set from site to work shop and back , providing and fixing 50mm dia shaft enclosing tube for top shaft , rewinding of 75 hp motor ( v.t. ) , 75 hp motor bearing no. 29324 , 75 hp motor bearing no. 6316 , impeller bowl assembly ( v.t. ) gun metal emplier , iv) repairs 75 hp v.t. pump oil starter , contact moveable , contact fixed , holding coil 440 v , transformer oil , connection rod , movable contact patty copper luges , starter wiring & repairing charges , v) 75 hp submersible motor pumps repairing , submersible motor rewiding , rutter bush bronze new , rutter grinding & cutting , 75 hp motor thrust bearing upper & lower , pump s.s. sleeves , boll rubber bush , gun metal bush , s.s. shaft 410 , submersible pump opening & refitting , making transportation arrangement of submersible motor & pump set from site to work shop and back , errection of submersible pump set/motor on jack well after repairs and giving test trial on load , pump impeller , vi) 75 hp submersible motor starter repairing , contact moveable , contact fixed , holding coil 440 v , transformer oil , connection rod , movable contact patty copper luges , starter wiring & repairing charges , vii) 75 hp vt ( water lubricating ) pump repairing , 75 hp bowl assembly ss shaft , 75 hp bowl assembly gunmetal impeller , 75 hp impeller neck ring gunmetal , 75 hp providing and fixing bowl assembly , 75 hp gunmetal bush , 75 hp bowl assembly rubber bush , 75 hp ss line shaft , 75 hp ss line shaft sleeve , 75 hp line shaft coupling , 75 hp gunmetal spider , 75 hp spider rubber bush , 75 hp bowl assembly tvs bolt , 75 hp casing pipe nut bolt tvs , 75 hp casing pipe rubber seat , 75 hp tt plate , 75 hp gun metal gland , 75 hp motor rewinding( without return copper wire scrap material ) , 75 hp motor rewinding(return copper wire scrap material ) , 75 hp motor bearings 6316 , 75 hp motor bearings 29324 , 75 hp transport vt pump set site to workshop and return to site , ats rewinding( without return copper wire scrap material ) , ats rewinding(return copper wire scrap material ) , viii) valve repairing , 300 mm sluice valve , 200 mm sluice valve , 150 mm sluice valve , 100 mm sluice valve , ix) 25hp air blower, starter and motor , 25 hp motor rewinding( without return copper wire scrap material ) , 25 hp motor rewinding(return copper wire scrap material ) , 25 hp ats starter repair , 25 air blower repair , new column pipe with flange 200mm