tender for external electrification work-2 supply & fixing of 10 mtr 01 octagonal pole of approved make ( top da 100 mm bottom dia 200 mm and bass plate 16mm thick ) having 3 mm thiness. 1 with double arm bracket 1 mtr length in 1:24 rcc foundation bolt including the cost of foundation, excavation & back filling and required t&p complete in all respect. 3 supply and thing of led street fight fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 watt. confirming to ip 66 and above protection complete in all respect. cat-aaa 4 supply and laying of aluminium conductor pvc insulated armoured served sheathed cable 1100 v grade at a depth of 750 mm below ground level over a cushion of 75 mm, thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps elc. of sultable size of as directed by the engineer in charge complete respect. the armouring of the cable shall be property connected with the earth conductor by clamps etc. 5 16 sq mm 4 core 6 25 mm 3-1 / 2 core 7 50 sq mm 3.5 core 8 supply and fixing of brass nickle plated compression gland for pvc insulated & amoured served sheathed, underground cable including rubber ring et 4 complete in all respect. the armouring of the cable shall be properly connected with the earth as por direction of engineeer-in-charge 9 16 sq mm 4 core 10 25 mm 3-1 / 2 core 11 50 sq mm 3.5 core 12 supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc, complete in all respect as per direction of the engineer-incharge. 13 16 sq mm 4 core 14 25 mm 3-1 / 2 core 15 50 sq mm 3.5 core 16 earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangerpent and watering pipe etc. with charcoal / coke and salt as required. 17 supplying and laying 6 swg dia g.i. wire at 0.50 meter below ground level for conductor earth electrode, including connection / termination with g.i. thimble etc as required 18 s&f of 6 amp. 10 32 amp. dp mcb ( 30 ka ) c curve cat-a 19 supply and wiring of submain with two number 2.5 sq.mm. frish pvc insulated 1100 v grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit concealed in wall, with one number 14 swg copper earth continuity wire etc, complete in all respects including matching colour wash etc, complete in all respect. 20 supply & fixing of 30 mtr high mast shaft of approved make with rising system hot dip glavanised inside & out side dip, heaving pole sheet, thickness 4 mm. top dia minium 150 mm, bottom dia 500 mm base plate 32 mm thick suitable for wind velocity as per is 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame, suitable for 8 to 12 luminaries & its control gear boxes 1.5 hp power tool moter, 3 point suspension system with steel wire rope 8 mm dia, double drum winch, including making suitable foundation as per manufature drawing / site reument along with foundation bolts nuts, washers, anchor plates etc completee in all respect. 21 supply and fixing of factory wired integral highmast light luminaires with die cast aluminium housing built with dirver set suitable for 500 watt. ip 66 protection complete in all respect. 22 main panel 23 supply & erection of factory fabricated & wired metal clad dust and vermin proof floor mounting. m.s. channel base with bottom and top cable entreis electrical control panel with tpn mccbs ( four pole 36k with thermal magnatic release ) switches complete and instrument chamber et.complete in all respects. the instrument chamber shall be separate and shall comarte of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters ( kva, p.f., kw etc ) in each phase with touch type selector witches for different readings, instrument fuses, current transformer etc.the panel board shall have suitable capacity electrolytic aluminum busbars as per is 8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supperts such as cmc / bmc support with deteachable side covers and shall be suitable for extension on the sides. the mccbs shall be complete with suitable cable end boxes, compression gands and indicating lamp on incoming etc. the job includes the grounting of the board as per directions of engineer-in charge. all out goings of 100 amp and above shall have an ammeter. the panel board shall be fabricated with crca sheet with a minimum thickness of 1.6mm / 2mm. cubicle type switch board shall be of cat a&b only. 24 incoming 25 200 amp mccb-1 no 26 outgoing 27 63 amp mccb-3 no 28 cat. b. pannel cubicle type 29 supply & erection of factory fabricated & wired metal clad dust and vermin proof floor mounting. m.s. channel base with bottom and top cable entreis electrical control panel with tpn mccbs ( four pole 36k with thermal magnatic release ) switches complete and instrument chamber et.complete in all respects. the instrument chamber shall be separate and shall comarte of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters ( kva, p.f., kw etc ) in each phase with touch type selector witches for different readings, instrument fuses, current transformer etc.the panel board shall have suitable capacity electrolytic aluminum busbars as per is 8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supperts such as cmc / bmc support with deteachable side covers and shall be suitable for extension on the sides. the mccbs shall be complete with suitable cable end boxes, compression gands and indicating lamp on incoming etc. the job includes the grounting of the board as per directions of engineer-in charge. all out goings of 100 amp and above shall have an ammeter. the panel board shall be fabricated with crca sheet with a minimum thickness of 1.6mm / 2mm. cubicle type switch board shall be of cat a&b only. 30 incoming 31 100 amp mccb-1 no 32 outgoing 33 63 amp mccb-2 no 34 cat. b. pannel cubicle type 35 sitc of 63 kva transformer complete 36 earthing with copper earth state 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 mete long etc. with charcoal / coke and salt as required. 37 supplying and laying 25 mm x5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut bolt, spring washer etc as required ( jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm ) 38 supply and laying of 3 core standered aluminium conductor xlpe ( cross inked polyethylene ) insulated pvc bedded, galvanised flat steel strip armoured cables confirming to is 7098 ( part-ii with latest amendments ) 11 kv grade at a depth of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks on sides and on top put across. the armouring of cable shall be properly connected with earth conductor by clamps etc. 39 95 sq mm 3 core 40 supply & fixing steel tubular pole 9.50 meter long designated 410 sp-39 in 1:3:6 cement concrete foundation including excavation back filling at complets in all respect. 41 supply & fixing of 100 mm x 110 mm shackle insulator / 100 mm x 80 mm 18 pin insulator including g.i. bolts / spindle nuts etc. complete in all respect 42 supply & erection of stay set at least 3.5 metres away from the pole complete with galvanised 19 mm dia x1.80 metre long stay rod. 30 cm x 30 cm x 6.3 mm anchor plate, thimble stay clamps, stay insulator, 19 mm x 600 double screw tightener, 7 / 4.00 mm gl stay wire etc. in 1:36 cement concrete complete in all respect. 43 painting of the electric pole with 2 coats of aluminium paint over redoxide primer complete in all respect. 44 sitc of tpmo complete 45 sitc of ms material ( l angle nut bolt etc ) 46 supplying and laying of following size dwc hdpe pipe isi marked along with all accessories like socket, bend, couplers etc. conforming to is 14930, part ii complete with fitting and cutting, jointing etc direct in ground ( 75 cm below ground level ) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required ( rate: 368.00-12%=328.6 ) 47 120 mm dia ( od-120 mm & id-103 mm nominal ) 48 supplying and laying of following size dwc pipe isi marked along with all accessories like socket, bend, couplers etc. conforming to 1s 14930, part-ii complete with fitting and cutting, jointing etc.direct in ground ( 75cm below ground level ) including excavation and refilling the trench complete. 49 100 mm 50 50 mm