tender for construction of permanent metalled fud in ngm at bapoli (assembly question unstarred d. no. 15/2/565 dated 03.03.2025)--1. [11.5.1]12 mm cement plaster of mix : 1. 1:2 (1 cement: 2 fine sand) [through rate] 374.03 sqm 2. [11.52]cement rendering on plaster 1 mm thick [through rate] 90.03 sqm 3. [17.15.3]granular sub-base with coarse graded material - grading-i or ii or iii (table:- 400-2) construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.of mortandh specifications 3. grading iii material [through rate] 862.23 cum 4. [17.5.3]compacting original ground 3. compaction of earthwork compaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the table 3000-2 as per technical clause 305 of mort&h specifications [through rate] 4386.07 sqm 5. [17.6]construction of embankment with material obtained from borrow pits na construction of embankment cbr 8% (for new road/ raising/ berms/ etc.) with approved material obtained from borrow pits, including compensation of earth with all lead and lift transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2, as per technical clause 305 of mort&h specifications. [through rate] 5176.72 cum 6. [17.69.2]interlocking concrete block pavement 2. providing and laying 80 mm thick isi marked interlocking paver blocks conforming to is 15658:2006/irc sp 63: 2004 of all shapes and colours in design mix cement m 40 over the bed of 30 mm thick fine sand complete in all respect. [through rate] 589.41 sqm 7. [20.49.1]bailing out water from the trenches for making new connections in fully charged pipe-lines including cleaning trimming and dressing the trenches to correct alignment and grade as required by the engineer-in-charge. size of the main with which connection is to be made. 1. up to 200 mm internal diametre [through rate] 8. [20.58.2]providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 2. 100mm i/d cid joint [through rate] 10.00 each 9. [20.63.1]`providing, lowering, laying in trenches, aligning, fixing in position and jointing ductile iron (di) isi marked k-9 grade sands pipes as per 15:8329-2000 (amended up to date), with internal cement mortar lining for potable water with rubber ring (epdm/sbr) joints as per is: 5382 -1985 (excluding special accessories) complete including all material, labour, hydraulic testing and commissioning as per technical specifications and as per direction of engineer. note: e/w to be measured and paid separately. ` 1. 100 mm i/d [through rate] 234.00 per metre 10. [20.66.1]cutting di pipe and chipping or filling the surface to a uniform finish 1. 100 mm i/d [through rate] 12.00 per cut 11. [20.67.1]joining di socketed pipes, valves and special with rubber tyton joints fitted complete including cost of labour and tools etc. and tested complete. 1. 100 mm i/d [through rate] 41.00 per joint 12. [20.68.1]providing, lowering, laying in trenches, aligning, fixing in position and jointing at all level/depths ductile iron (di) standard specials plain /flanged/ socketed confirming to is9523-2000 with rubber ring (epdm/sbr) joints such as tees, bends, tapers, caps etc. with in trenches in di pipe line complete including all material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer. 1. up to 300mm dia [through rate]