tender for remaining work of covered threshing floor- (under rkvy) at kvk sawai madhopur - covered threshing floor 2 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level.m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 3 supplying and filling in plinth with blown sand under floors including watering ramming consolidating and dressing complete including cost of sand. 4 random rubble dry stone kharanja under floor. 5 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix 6 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 7 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mix colums 8 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level.thermo-mechanically treated bars (conforming of relevent is code) 9 random rubble stone masonry for foundation and plinth in cement sand mortar above 30 cm thick wall in : cement mortar 1 : 6 (1-cement : 6-sand). 10 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1 : 6 (1 cement : 6 coarse sand) 11 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :25 mm thick 12 providing&fixingprecastcementconcretecoping1:2:4mix50mmthickcompleteas per specification : 13 structural steel work riveted,bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: 14 steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete.hot finished seamless type tubes. 15 supply and installation of multi rib proofing /cladding sheet manufacture out of 0.50mm tct( total coated thickness) high tensile zinc aluminum alloy coated galvaiume steel ( as per 150gsm zinc aluminum coated 550mpa yield strength)confirming to is: 1397/astm a -792 sheet to have wide pens 30mm high nb at 250centre and centre width of 1020 mm shets be casted with regular modifedpolyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have propportionality with siphoned plate atmade at to prevent lrakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. the sheet shall be supplied in cost one length and foe a minimum up to 12 mts with all scaffolding. 16 roof ridge cap:ridge flashing for roof panels shall be made from 0.5mm thick pre-coated ppgl sheet of 200mm x200 mm.