supply of cs item on conversion / supply basis and forged steel item cs item on conversion / supply basis and forged steel item , c.s coupling having material as per is:1030 grade 280-520w for mill size 30x60 as per drg. , supply basis , conversion basis , machining charge , cast steel crown pinion having material is:2708 grade-iii-b for mill size 30x 60 as per drg. , supply basis , conversion basis , machining charge , c.s.trash plate having material as per is:1030 and grade-iii-b , supply basis , conversion basis , machining charge , teeth cutting / grooving of trash plate as per drg. , c.s.trash beam as per is-1030 / is 2708 as per drg. , supply basis , conversion basis , machining charge , forge steel tail bar for taxmaco and kcp mill having material c-40 / 8 as per drg. mh- 6 & mh-56 , supply basis , conversion basis , forge steel pinion for transmission gear of taxmaco mill as per drg. no. mh 39, material en-24, tensile strength70-80 kg. / sqcm, hardness 200-220 bhn , c.s.bearing housing for taxmaco mill as per deg no mh-17-c / 04 side roller housing , supply basis , conversion basis , gun metal bearing housing for taxmaco mill as per deg no mh-17-c / 04 top roller housing , supply basis , conversion basis , c.s.bearing housing for k.c.p.mill as per drg no mh-17-b side roller housing , supply basis , conversion basis , c.s.bearing housing fork.c.p.mill as per drg no mh-17-b top roller housing , supply basis , conversion basis , c.s.gear coupling for c / f machine as per drg.no.bh-14 ( duly case hardness ) , c.s. pinion for cane unloader as per drg, cu- 16teeth-17 , teeth -18 , c.s.sprocket 2 pitch ( both pilot bore ) , no of teeth 18 , boss dia 3 , no of teeth 36 , boss dia 6 , c.s.sprocket for boiler rotary feederas per drg.blr-73 / 1 pitch- 25.0 mm, no of teeth 21, od -180mm. p.b -25mm , , c.s.sprocket for bagasse elevator ( pilot bore ) as per drg.mh-75 pitch 50.8 mm, no of teeth 50, od 842.70mm. pcd 808.7mm, teeth thickness 28mm , boss- 270x130 mm , cs sprocket ( pilot bore ) as per drg.blr-62pitch 50.8 mm, no.of teeth-14 pcd 226.49mm, od 258.8mm , static coller of 25 mm thick duly hard faced of 5 mm thick layer . total thick 30 mm after hard facing for taxmaco & kcp mill as per drawing no. mm 105 , m.s. material , c.s.material , sprocket of inter carrier od 280 mm, no.of teeth45.pitch 19.5 mm , c.s. sprocket ( duplex ) for enter carrier teeth 12, as per drg. mh-72 / sample , s.s. wear plate is 304 quality , 435 mm length x 370 mm width x 15 mm thick , 385 mm length x 330 mm width x 15 mm thick , c.s.tresh beam bracket as per sample / drg. , c.s.eccentric pin for taxmaco as per sample / drg. , c.s. trash beam adjusting connecting rod for taxmaco mill, as per drg. mh- 297 , bridge wheel for cane unloader as per sample / drg. , trolly wheel for cane unloader as per sample / drg. , pinion gear set for cane unloader as per sample / drg , c.s. pinion ( gear ) for rbc cross carrier pitch 41mm. teeth 25 , type of teeth in valute ( spur ) module 12.7 mm width 125 mm .od 343 mm, bore 2 dia as per drg. , clutch shaft for mill. as per drg. mh-76 , en-8 , for taxmaco mill -sl.no.2 , for kcp mill - sl.no.1 , cs worm for crystilizer wheel od 290 mm, bore 81 mm.pitch 80 mm complete , groving of c.strash plate as per drg. , groving of ci scrapper as per drying , idler wheel gear for cane unloader., no of teeth 68, od-420 mm, module-6, pitch- 18.84 mm, pcd-408 mm, as per drg. no. cu-25i , pinion for cane unloader no. of teeth- 33, od-212 mm, pcd-198 mm, pitch- 18.84 mm, module-6 as per drg. no. , pinion for cane unloader no. of teeth- 18, od-200 mm, pitch- 35 mm, bore- 50 mm, width-115 mm, module-6, teeth depth-25 mm as per drg. no. , break stand complete for cane unloader, size-10 , chief engineer