supply of material for balance work construction of home guard training center jhansi district jhansi.-bricks , 20mm guage approved stone grit , coarse sand , 6 supply of pozonolla portland cement as per isi code 1489-2015 ( prism, birla, acc. jaypee or equivalent ) every bag shall be deemed to contain 50 kg. of cement. the suppliers may liable to submit the test report . 7 supply of oil bound distemper of approved brand and manufacture & of required shade for undecorated wall surface to give an even shade overapproved brand & manufacture such as berger, asian paints 8 supply ofpremium acrylic smooth exterior paint with silicone additives of required shade :.manufacture such as berger, asian paints 9 supply of puttyof approved brand manufacture such as birla white putty , jk wall putty 10 supply ofisi marked flush door shutters conforming to is : 2202 ( part i ) non-decorative type, core of block board construction with frame of 1st class hard wood & well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including isi marked stainless steel butt hinges with necessary screws. required size as per site requirment 11 supply of m.s. or iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. providing & fixing of hold fast for chaukhatsof doors and windows. 12 supply of m.s. or iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. providing & fixing of door / windows grill. 13 supply of m.s. or iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. z-section steel windows 14 supply of m.s. or iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work.angle iron door chaukhats 40*40*5 15 supply ofwire gauge laminated veneer lumber shutters conforming to is : 14616, and as per tads 15 :2001 ( part b ) using galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm as per is :1568, for doors, windows and clerestory windows, including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws, as per directions of engineer-in-charge:30 mm thick shutters 16 supply of stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, 17 supply of stainless steel sliding door bolts isi marked to required colour or shade with nuts and screws etc complete. ( a ) 250mm x 16mm . 18 supplyof stainless steel towerbolts ( barrel type ) with necessary screws etc complete ( a ) 250 mm x 10mm 19 supply of stainless steel towerbolts ( barrel type ) with necessary screws etc complete ( a ) 200 mm x 10mm 20 supply of stainless steel handles with screws etc. complete ( a ) 125 mm 21 supply ofsynthetic enamel paint such as luxol3, hi-gloss apcolite superlac, dulux , asian , berger 22 supply ofglass panes3.8 to 4.7 mm thick manufacture as per modi, atul approved brand 23 supply of light cinder filling under floor of toilets & other sunken roofs. 24 supply of isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. ( a ) 25 mm thick ( for cupboard ) including isi marked nickel plated bright finished m.s. piano hinges is : 3818 marked with necessary screws & one side laminated. 25 gst extra as per applicable