providing installation testing and commissioning of various electromechanical equipments at wss pampora-1 providing installation testing and commissioning of new horizontal pump , for wss pampore r / w nhorizontal split case pump n• make:wilo n• discharge: 300m3 / hr. n• head: 40mtr. n• speed :1450 / 1480rpm n• efficiency > 80% n• npshr =2.5 n nthe new unit shall be connected to existing suction ( 200mm ) and delivery line ( 150mm ) without any alteration to the existing setup of suction / delivery. the scope of work shall include all the mechanical jobs, nuts, bolts, alignment, leveling and tools and tackles necessary for installation and testing of the said pumping unit .the job also includes providing of 05 kg palmative packing of required size and four no of bearings ( two for each pump ) as spare to be used for preventive maintenance. nas par annexure a 2 providing, installation testing and commissioning ofmccb of the following specifications at pampore ( r / w ) : ncurrent rating : 250 amp. nno of poles: 4pole nbreaking capacity: 50kv ntype of release: thermal-magnetic release nconforming to is / iec 60947-1, iec 60947-2 & iec 60947-3. nthe job includes providing and fitting of spreader terminals including providing& fitting of the suitable size copper thimbles on both input and output terminals. napproved make:l&t / abb / simens n 3 providing, fitting, testing and commissioning of 150mm nominal dia. heavy duty ductile iron sluice valve of rating pn 1.6 conforming to is / 14846 ( 2000 ) .the valve shall have body and bonnet of ductile iron fully covered with rubber ( epdm ) approval identical seal on both sides, with integrated rubber joint protected against overload, body seat cast iron, bolts and nuts of stainless steel ( a2 ) . ncorrosion protection: ninside and outside epoxy coating, blue, ral 5005 according to gsk. the job includes p / f of 02 no. m.s. flangesconforming to is / 6392 perfectly adaptable to the inbuilt flanges of the valves, which shall be fitted at the suitable place in the rising mains , cost on account of nuts, boltsconforming to is / 1363 part-ist ( 2002 ) &gasketsconforming to is / 638 / 79 required for the completion of job is included in the scope of work. napproved:vag / avk / tallis n 4 providing, fitting, testing and commissioning of 150mm nominal dia. heavy duty ductile iron , nrv of rating pn 1.6 conforming to is / 5312 ( 2000 ) . the valve shall have body and bonnet of ductile iron, with drainage plug disk of ductile iron, fully covered with rubber ( epdm ) approval identical seal on both sides, with integrated rubber joint protected against overload, body seat cast iron, bolts and nuts of stainless steel ( a2 ) . ncorrosion protection: ninside and outside epoxy coating, blue, ral 5005 according to gsk. the job includes p / f of 02 no. m.s. flangesconforming to is / 6392 perfectly adaptable to the inbuilt flanges of the valves, which shall be fitted at the suitable place in the rising mains , cost on account of nuts, boltsconforming to is / 1363 part-ist ( 2002 ) &gasketsconforming to is / 638 / 79 required for the completion of job is included in the scope of work. napproved: approved:vag / avk / tallis n 5 providing, installation, testing and commissioning of fully automatic star-delta starter conforming to is13947-4 & iec 60947-4 with relay range 90-150 amp. the starter shall be sheet enclosure type suitable for operating on 3 – phase, 415 v, 50 hz ac power supply. the starter shall be able to provide single phase, phase reversal, phase imbalance and overload protection to the motor. the starter shall also consist the on / off, voltage and current indication. the job includes p / f of nut bolts, washers and fitting of same on panel board. the job includes minor wiring i.e. connecting of main incoming and outgoing connection leads duly crimped with copper thimbles and testing on full load at site. napproved: l&t / abb n