tender for repair / replacement of windows, doors ventilators, roof treatment and other misc b/r works at area-ii of age b/r-ii under ge kamptee.; 1 taking down door / window frame with shutter (without taking of shutter from the frame )area n. exc 1.50 sqm complete all as specified and as directed. 2 taking down door / window frame with shutter (without taking of shutter from the frame )area exc 1.50 sqm but not exc 4 sqm complete all as specified and as directed. 3 taking down existing water proofing treatment including pcc padding, mortar etc and disposal of rubbish outside of md land and hacking for key, scrubbing down with water complete all as specified and as directed. 4 m&l for provision of water proofing treatment by using app torch on non woven polyster film reinforcement with 3 mm thick and weight not less than 3.00 kg/sq m over roof and vertical surfacesincluding preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sqm on clean and dry surface and then providing app membrane laid with 100 mm over lap on both sides all as per manufacturers instructions including 15mm thick cement plaster in cm 1:4 with wpc and two coat of aluminium paintof 0.2kg/sqm over membrane complete all as specified and as directed. 5 taking down shutter of any description exc 1 sqm but not exc. 2 sqm each and removing from site complete all as specified and as directed. 6 s&f 30 mm thick flush shutters solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed. 7 all as per item no.08081 but wire gauzed i.e. panel will be of wire gauze in lieu of wood grain printed pvc sheet panel. the wire gauze shall be wrapped on an additional square 8mm m.s. solid tube and this tube shall be welded to m.s. tubes. the wire gauge shall be stretched to tighten firmlycomplete all as specified and as directed. 8 hacking out old broken glass (any thickness size and quality and description) from wooden/steel/aluminium frames glazed with putty or fixed with beads etc complete all as specified and directed 9 s&f 4 mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete. 10 s&f 4 mm thick glass, ordinary quality and glazing with oil putty/wooden beads in square exceeding 0.5 square metre in each pane complete. 11 s&f 4 mm thick glass, ordinary quality and glazing with oil putty/wooden beads in square exceeding 0.5 square metre in each pane complete. 12 s&f stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed. 13 all as per ssr no 08095 but wood grain printed pvc sheet used instead of plain colour pvc sheet & edges will be painted to match with printed sheet complete all as specified and as directed. 14 factory made solid pvc moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded pvc sheet on the front face & 2mm plain colour pvc sheet on back face, with wood free eps, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed. 15 s&f butt hinges medium weight cold rolled stainless / mild steel 100mm size complete all as spd and directed. 16 supply & fixing 150mm aluminium barrel tower bolts, fixed complete all as specified and as directed 17 supply & fixing 150 mm aluminium pressed handles fixed complete all as specified and as directed. 18 s & f 250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and as directed. 19 s & f in repairs 40 mm dia, cupboard knobs fixed with nut, screws and washer of mild steel, bright finished 20 s & f powder coating aluminium frame for doors, windows , ventilators with one or more rebates incl joining cleat for fixing etc. complete all as spd. (thickness or powder coating not less than 50 micron) 21 s&f powder coating aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing,02 nos handles, anodised aluminium snap beading, screws, sliding wheels, including concealed ss body type arragement etc. complete all as specifiedand directed. (thickness or powder coating not less than 50 micron) complete all as specified and as directed.note-(i) glass and other filling material in panels shall be measured and paid seperately 22 s&f powder coating aluminium window / ventilator shutters, sliding type, slides of two/three/four track without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, sliding wheels, including concealed ss body type arragement etc. complete all as specifiedand directed. (thickness or powder coating not less than 50 micron) complete all as specified and as directed.note-(i) glass and other filling material in panels shall be measured and paid seperately 23 s&f powder coated aluminium ventilator louvers type section aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc louvers after open use in ventilator in order to allow air or light in while keeping sun in or moisture out complete all as specified and as directed.(thickness or powder coating not less than 50 micron) complete all as specified and as directed.note-(i) glass and other filling material in panels shall be measured and paid seperately 24 material & labourfor preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. 25 m&l for preparation of new steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint etc complete all as specified and as directed. 26 s&f pre-polished granite 20mm thick fixed on platform/shelves/steps/cill over 20mm thickscreed bedin cement mortar 1:4 including necessary moulding etc complete all as directed. 27 dismantling boarding, any description, fixed in any position with screw ,complete all as specified and as directed. 28 s& f in repair 18 mm thick alstone wood polymer composiveboard ( wpc) in cupboard shutter and like with decorative on both side design fixedby drilling screws and brackets all as specified all as directed. 29 s&f 12 mm thick particle board, medium density, flat pressed, single layer type or three layer type with bwr type adhesive fixed in aluminium doors, cabinet self,etc complete all as specified and as directed . 30 s&f in repair continuous (piano) hinges, ss, bright finish with 30 mm width of flaps (when open), complete all as specified and as directed. 31 s&f magnetic catcher of size 20mmx50mm suitable for cup board shutters complete all as specified and as directed. 32 s&f in repair for curtain rails, mild steel, chromium plated with fixing brackets,stops,rollers etc complete all as specified and as directed. 33 dismantling of asbestos cement sheet (corrugated, semi-corrugated etc) sheets in roof coverings complete all as specified and as directed. 34 m & l for 0.50 mm thick prepainted galvalume aluminium zinc coating g.i. based corrugated steel sheet(az150) of any colour having tensile strength of 550 mpa as in roof covering, fixed with and including self tapping screw/j-type bolt/l-type boltcomplete all as per manufacturer instructions. 35 m & l pre-painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick (az150)of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws/j-type bolt/l-type boltcomplete all as specified and as directed. 36 dismantling of timber fillets,rails, posts, rafters, purlins under 40 sq cm in section complete all as specifed and directed. 37 s&f steel work in tubular trusses including special shaped washer etc. complete using erw or induction butt welded tubes conforming to i. s 1161-1979 grade st.-240 complete all as specified and as directed. 38 s&f mild steelwork such as roof trusses (framed), trussed, purlins, and heavy bracket framing (beam, tee, angle, channel or flat section) including distance pieces, cleat etc complete all as specifiedand directed. 39 dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets any thickness and wall paneling including cover fillets,complete all as specified and as directed. 40 m&l for 4mm thick non asbestos, fibre cement building board of size 595x595mm size in ceiling fixed or laid/ inserted including gi powder coated snap grid framework for false ceiling comprising of the following section for making partition of 600x600 mm size fixed to wall with rawl plug and screw and hanged to roof with 4 mm dia gi suspended wire of suitable length and butterfly clip of size of main tee shall be 32mmx15mmx0.30mm, cross tee shall be 32mmx15mmx0.30mm thick with black lining in mid portion and wall angle shall be 24mmx24mmx0.30mm thick complete all as specified and directed