tender for annual plan-pp2025-26/project n0 165/ rennovation of cdpo office -amount 636011/--general civil work - cdpo office 2 10.2:structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 3 10.1:structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 4 4.1.3:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-iii)derived from natural sources : 4 graded stone aggregate 20 mm nominal sizederived from natural sources) 5 4.3.1:centering and shuttering including strutting, propping etc. and removal of form work for:foundations, footings, bases for columns 6 od212234/2025-2026:supplying and fixing 160 mm dia upvc rain water gutter (rectangular section) of minimum 650gm/m density with all fittings like elbow, drop etc. including all 7 50.18.9.19.2:providing and fixing pvc pipes including fixing the pipe with clamps/clips at 1.00 m spacing. this includes jointing of pipes with one step pvc solvent cement and testing of joints complete as per direction of engineer-in-charge 110 m dia 4 kgf/cm2 - external work - exposed on wall 8 od212916/2025-2026:finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturers specificationspreparation of surface,excludingpriming coat,etc. complete.on steel work (dsr 13.52.1) 9 od213222/2025-2026:providing and fixing aluminium profile sheets (size, shape and pitch of corrugationas approved by engineer-in-charge) 0.45 mm (+/-0.05), total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer-in-charge. the sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required 10 od213285/2025-2026:providing and fixing precoated aluminium sheet roofing accessories 0.45 mm (+/- 0.05) total coated thickness, colour coated as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self 11 50.9.1.1:providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality anjili wood /jack wood 12 50.9.3.1:providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f engineer in- charge. using anjili/ jack wood 13 50.9.4.1:providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality anjili/ jack wood 14 15.12.1:dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:of area 3 sq. metres and below 15 13.62.1:painting with synthetic enamel paint of approved brand and manufacture of required colour to givean even shade:two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture . 16 50.9.15.1:supplying and fixing 200 mm aluminium aldrop 17 9.53:providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 18 9.63.3:providing and fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete : (copper oxidized as per is : 1378)150x10 mm 19 9.77:providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete 20 od213346/2025-2026:supplying and fixing name board including all charges complete