tender for repair and maintenance works of toilet block in office building at cws rampur => limited; 1 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointingwith grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm 2 providing and fixing ist quality ceramic glazed wall tiles conforming to 1s: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarsesand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 3 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead for thickness of tiles 10 mm to 25 mm 4 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 5 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand) 6 finishing with deluxe multi surface paint system for interiors and exteriorsusing primer as per manufacturers specifications : two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm 7 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled devicehandle lever) conforming to is : 7231, with all fittings and fixtures complete, includingcutting and making good the walls and floors wherever required: white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 8 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device(handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid 9 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps 10 providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. 11 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. flexible pipe 40 mm dia 12 providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 13 providing and fixing factory made p.v.c. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid pvc foam sheet, mitred at corners and joined with 2 nos of 150 mm long brackets of 15x15 mm m.s. square tube, the vertical door frame profiles to be reinforced with 19x19 mm m.s. square tube of 19 gauge, epdm rubber gasket weather seal to be provided through out the frame. the door frame to be fixed to the wall using m.s. screws of 65/100 mm size, complete as per manufacturers specification and direction of engineer in-charge. 14 providing and fixing factory made panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture. m.s. frame covered with 5 mm thick heat moulded pvc ‘c’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide pvc sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide pvc sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross pvc sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side pvc sheet to be fitted in the m.s. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide pvc sheet beading on inner side, and joined together with solvent cement adhesive. an additional 5 mm thick pvc strip of 20 mm width is to be stuck on the interior side of the ‘c’ channel using pvc solvent adhesive etc. complete as per direction of engineer-in-charge, manufacturer’s specification & drawing. 15 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surfaceto prepare the surface even and smooth complete