balance work (i.e plastering , priming, painting, panel shuttering etc. ) of raghunathchak primary school under ward no. 06 within haldia municipality. ( the rate are based as per schedule of rates with latest revision for building works ( volume - i ) ( including materials, labour & carriage ) effective from 1stnovember 2017 & including 16th corrigenda effective from 21.10.2022)- 1 page no. - 11/10stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. 2 page no. - 189/1plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor).[excluding cost of chipping over concrete surface](ii) with 1:6 cement mortar(b) 20 mm thick plaster 3 (ii) with 1:6 cement mortar(b) 15 mm thick plaster 4 (iii) with 1:4 cement mortar(c) 10 mm thick plaster 5 page no. - 117/1(iii) (b)panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.in ground floor.(in case of non-supply of single plank, penal rate of reduction of 20% will be made)(iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm.(b) sishu, gamar, champ,badam,bhola, mogra, hallak 6 page no. - 140/5iron butt hinges of approved quality fitted and fixed with steel screws, with isimark.(vi) 100mm. x 50mm. x 1.25mm 7 page no. - 144/26 anodised aluminium barrel / tower / socket bolt (full covered) of approvedmanufactured from extruded section conforming to i.s. 204/74 fitted and fixedwith cadmium plated screws:(ii) 75mm long x 10mm dia. bolt. 8 (v) 150mm long x 12mm dia. bolt. 9 page no. - 145/30 a (iv)anodised aliminium d-type handle of approved quality manufactured fromextruded section conforming to i.s. specification (i.s. 230/72) fitted and fixedcomplete:(a) with continuous plate base (hexagonal/ round rod)(ii) 100 mm grip x 10 mm dia rod 10 page no. - 141/10i) iron hasp bolt of approved quality fitted and fixed complete (oxidised) with16mm dia rod with centre bolt and round fitting.(c) 300mm long. 11 page no. - 195/7 applying interior grade acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive distemper/ acrylic emulsion paint including scraping and preparingthe surface throughly, complete as per manufacturers specification and as per direction of the eic.(in ground floor)(a) one coati) water based interior grade acrylic primer 12 page no. - 201/4 applying acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of superintending engineer) : (two coats) ii) luxury quality 13 page no. - 196/8 applying exterior grade acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterioremulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the eic(b) two coatsground floor 14 page no. - 197/17 (c)protective and decorative acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction of engineer-in-charge to be applied over acrylic primer as required. therate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.a) normal acrylic emulsionin ground floor (two coat) 15 page no. - 200/1 (b) (b) priming one coat on timber or plastered surface with synthetic oilbound primer of approved quality including smoothening surfaces by sandpapering etc. 16 item no. 37 / page no. - 200/2 (a) painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary :(a) on timber or plastered surface :with super gloss (hi-gloss) -(iv) two coats (with any shade except white) 17 page no. - 213/21supplying, fitting & fixing upvc pipes a- type and fittings conforming to is:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (spun yarn, valamoid/bitumen/m-seal etc) complete.a) upvc pipes:(ii) 110 mm. dia. 18 b) upvc fittings:c) bend 87.5 degree110mm 19 gst item (effect from 18.07.2022)18 % gst on estimated cost of sl no- 1 to 14.1 20 labour welfare cess item (effect from 01.11.2017) 1% labour welfare cess on estmated cost of sl no -1 to 15