tender for repairs to fencing, gates, concertina coil, pcc at 3 afru chandan under ge (af) jaisalmer; 1 dismantling posts or struts (wood, steel or r.c.c.) any section, including taking out embedded portion and making good disturbed ground complete all as spd and dir. 2 excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance nexc 50m and making good distrubed surface for any type of soil complete all as spd and dir.(size of holes minimum (0.75mx0.75mx0.75m) 3 m & l pcc 1:3:6 type c-2 (using 40mm graded stone aggregate) as in foundation for concrete post/struts complete all as spd and dir. 4 s&f mild steel angle ironposts and struts in fencing including cutting tops to shape as directed,drilling holes,notching for wire,etc;flat iron fillets(for securing wire mesh etc) including all necessary drilling ,bolting or riveting,etc, andsimilar works conforming to fe-410-0 or fe-310-0. 5 s & f round tie bars 10mm dia conforming to fe290 gde e-165 let in and fixed independantely incl hooking ends for securing wire mesh chain link fencing as in bearing bars complete all as spd and dir. 6 ditto all as per item no above but except bars 7 dismantling chain link fencing wire, any type complete all as spd and dir. 8 fixing only chain link fencingincluding line wires, any mesh, size and type of standards, rails, straining bolts etc. including provision of binding wire complete all as specified and directed 9 supply only ms galvanized chain link fencing any size and type complete all as specified and directed 10 s&f mild steel screw bolts (machine made) with hexagonal or square head and one end screwed or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut, exc. 5 cm long & diameter of neck 5 to 10mm complete all as specified and directed . 11 s&f in repair galvanized, 2 strand, steel barbed wire, 2.24 mm dia barbed with 2 mm dia barbs at 75 mmspacing and straining and fixing to any type of standard rails, straining boltsincluding securing or tying atcrossing with and provision of galvanized ms wire staples or steel pins etc as specified. (each line wire to be measured). complete all as specified and directed 12 all as per item no. 20 above but restraining resecuring including making good staples etc complete all as spd and dir 13 supply & fixing concertina coil with core wire diameter of 2.5mm, blade thickness ranging from 0.4mm to 0.6mm and coil diameter 750mm dia complete. 14 dismantling structural steel work including doors, gates but excluding framed truss etc. 15 framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete 16 m & l pre-cast cement concrete block masonry with solid blocks, type c-1 1:3:6 (using 20mm stone aggregate)exc. 10 cm in width and setting in mortar,incl dismantling of damage/ extg wall complete all as spd and dir 17 m&l pcc 1:2:4 typeb-1 (using 20mm graded stone aggregate) as in coping, benching etc incl necessary form work complete all as specified and directed 18 m&l 15mm thick cement plastering in cement morter 1:4 on other than fair faces of brick/concrete/stone work finsihed cement complete all as spd dir. 19 m & l for preparation of new plastered surfaces of wall and applying two coats of exterior emulsion over a coat of primer complete all as spd and dir. 20 m&l preparation of new steel surfaces of any description,exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed . 21 m&l preparation of old steel surfaces of any description,exc 10 cm width or girth and applying two coats of synthetic enamel paintcomplete all as specified and directed . 22 m&l preparation of old steel surfaces of any description,n exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed . 23 m&l welding in repairs n.exc 2.5 cm in length, thickness of mild steel members to be welded not exc 6 mm complete all as specified and directed. 24 m&l welding in repairs exc 2.5 cm but n. exc 5 cm in length, thickness of mild steel members to be welded not exc 6 mm complete all as specified and directed. 25 m & l holes drilled up to 12mm dia (and countersunk, if required) depth of holeexc 3mm but nexc 12mm complete all as spd and dir. 26 m&l 75mm thick pcc 1:2:4 b-2 (using 40mm graded crushed stone aggregate) as in floor, path and similar finished even and fair all as specified. 27 excavating in trenches n exc 1.5m wide and n exc1.5 m in depth for foundation etc and getting out soft /gard soil.