tender for special repair of bldg no t-915 (or living accn) and p-82/c4, p-82/c6 (toilet block) at lt ad wksp under ge 865 ews; 1 demolition of cement concrete (un reinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) and removing debris off the premises complete all as specified and/or as directed by engr-in-charge. 2 demolition brick work / block masonry or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and/or directed by engr-in-charge. 3 dismantling floor, hearth or wall tiling including cement mortarbedding (but including backing), removing rubbish off the premises complete all as specified and/or as directed by engr-in-charge. 4 dismantling wall and ceiling boards (fiber, pulp, insulation, blankets) etc. any thickness including covered fillets and supporting members, complete all as specified and/or directed by engr-in-charge. 5 dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc.under 40 sqcm in section, complete all as specified and/or directed by engr-in-charge. 6 demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by engr-in-charge. 7 taking down cement plaster on brick/pcc block or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by engr-in-charge. 8 taking down chowkat or frame with shutters (without taking of shutters from the frame)not exc 1.5 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by engr-in-charge. 9 taking down chowkat or frame with shutters (without taking of shutters from the frame)exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by engr-in-charge. 10 dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and/or as directed by engr-in-charge. 11 hacking out old broken glass (any thickness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and/or directed by engr-in-charge. 12 dismantling plain or corrugated steel sheeting any gauge or thickness including nanital or similar pattern complete all as specified and as directed by engr-in-charge. 13 dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and/or directed by engr-in-charge. 14 m&l for9mm thick prelaminated particle boardmedium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed. 15 m&l for9mm thick prelaminated particle boardmedium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in ceiling panelling, complete all as specified and as directed. 16 m&l for 2nd class soft wood clean sawn as in battens for grids of ceiling & liningfixed with nails exc 13 sqcm and not exc 25 sqcm in section, complete all as specified and directed by engr-in-charge 17 m&l for 2nd class soft wood clean sawn as in battens for grids of ceiling & liningfixed with nails exc 6 sqcm and not exc 13 sqcm in section, complete all as specified and/or as directed by engr-in-charge. 18 m&l for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and/or as directed by engr-in-charge. 19 m&l for 75 mm thick pcc 1:3:6 type c-2 (using 20mm graded aggregate) as plinth protection finished even and smooth with out using extra cement, complete all as specified and/or as directed by engr-in-charge. 20 m&l forming contraction (dummy) joints 65 mm deep x 10mm wide, filled with sealing compound grade a in plinth protection, complete all as specified and/or as directed by engr-in-charge. 21 m&l for pcc 1:4:8, type d2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by engr-in-charge. 22 demolition of reinforced cement concrete of any description and position not otherwise specifically provided for. 23 m&l for cement concrete type 1:4:8,d-2, (using 40mm stone graded aggreate) 75 mm thick as in sub -floors, sub- bases, floors and pavings etc., complete all as specified and as directed. 24 m&l forchequred cement concrete tiles 30cm x 30cm x 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments and laid over & including 20mm thick cement screed base (1:6) complete all as specified and/or as directed by the engr-in-charge. 25 m&l form work for rough finished concrete surfaces to sides and soffits of floor or roof beam ,beam haunchings ,girders, bresum-mers,lintles,cantilevers,shelves including supports ,overhanging, etc. also splays between floors and beams, etc, complete all as specified and directed. 26 form work to edges of concrete flats in floors openings in concrete walls floor and roof and sides of rcc/pcc bands in walls horizontal or sloping and similar work not exc 20 cm wide complete all as specified and as directed by engr-in-charge. 27 m&l mild steel tmt bars 10mm dia and over, cut to length, bent to shape required, includingcranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than0.9mm dia or securing with clips quality conforming to tmt bar, complete all as specified and/or as directed by engr-in-charge. 28 m&l forhardcore of broken stone gauge not exc 63mm , deposited, spread and levelled in layers not exc. 15cm thick watered and rammed to a true surface, complete all as specified and as directed. 29 s&f rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guide, complete all as specified by engr-in-charge for sliding doors fixed with angle cleats or other connecting plates fe -410 gde e-250 quality-a, complete all as specified and/or directed by engr-in-charge. 30 m&l for preparation new steel surfaces of any description, not otherwise described, over 10 cm width / girth and applying two coats of synthetic enamel paint ovea a coat of red oxide primer, complete all as specified and/or as directed by engr-in-charge. 31 m&l precast solid blocks in cement concrete 1:3:6 type c-1 (20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by engr-in-charge. 32 m&l for 10mm thick rendering on fair faces of block/ brick wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and/or directed by engr-in-charge. 33 m&l for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 including mixing of liquid water proofing compound as per manufacturers instructions complete all as specified and as directed by engineer-in-charge. note : wpc will be measured and paid separately. 34 supply only integral liquid water proofing compound.make : pidilite/sika/asian paints. 35 m&l for preparation of new plastered wallsurface of any description and applying two coats of cement based paintcomplete all as specified and/or as directed by engr-in-charge. 36 s&f 35mm thick 2nd class hard wood plain framed factory made panelled shutters (any number ofpanels) with panels of timber flat on both sides (feather edged), or ofveneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and/or as directed by engr-in-charge. 37 s&fpowder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and/or as directed by the engr-in-charge. 38 m&l for powder coated aluminium door shuttlers, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, hinge type b-21 100 mm longs (3 nos) suitable handle (2 nos) (glass / wiremesh should be measured seperately) complete all as specified and/or as directed by engr-in-charge. 39 s&f anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sash, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type b-21 100mm long (2 nos) suitable handle (1 no) etc. complete all as specified and/or as directed by engr-in-charge. 40 s&f 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and/or as directed by the engr-in-charge. 41 m&l for preparation of new untreated wood or wooden based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and/or as directed by engr-in-charge. 42 m&l sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and/or as directed by engr-in-charge. 43 m&l sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and as directed. 44 s&f galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and/or as directed by engr-in-charge. 45 s&f 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and/or as directed by engr-in-charge. 46 s&f 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and/or as directed by engr-in-charge. 47 s&f in repair aluminium (die cast) body door closer hydraulically designation no 3 universaltype suitable for door shutter of 851 to1000mm in width and weight61 to 80 kg complete all as specified and/or as directed by engr-in-charge. 48 s&f floor door stopper (length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel springfixed in floor complete all as specified and/or as directed by engr-in-charge. 49 s&f 100mm long aluminium anodized, butt hinges of extruded section type b-21, complete all as specified and/or as directed by engr-in-charge. 50 s&f 100mm long mild steel butt hinges, medium weight cold rolled, complete all as specified and/or as directed by engr-in-charge. 51 s&f 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and/or as directed by engr-in-charge. 52 m&l for 25 mm thickpcc 1:2:4 type b1 (using 20mm graded stone aggregate) as in sub base complete all as specified and/or as directed by engr-in-charge. 53 m&l for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exc. 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cm 1:4 complete all as specified and/or as directed by engr-in-charge. 54 m&l for non - skid coloured ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and/or as directed by engr-in-charge. 55 m&l for glazed ceramic coloured tiles in vertical surfaces of size 450x350x7mm/ 350x250x7mmthick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortar (1:4) as in backing coat complete all as specified and/or as directed by engr-in-charge. 56 m&l for dismantling water tanks exc 250 but not exc 500 litres, and removing to store, complete, all as specified and as directed by the engineer-in-charge. 57 s&f tripple layered rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in ssr part-i of capacity 500 litres including all accessories, complete all as specified and/or as directed by engr-in-charge. 58 s&f mild steel work as in hold fastsand similar work confirming to fe-290 or gd -e 165 complete.all as specified and as directed by the engr-in-chage 59 material & labour pcc (1:3:6) type c1 (using 20 mm graded stone aggregate) as in hold fast, bed block and likecomplete all as specified and as directed by the engr-in-charge. 60 s&fin repairs towel hanger with 6 nos of pin and600mm long chromium plated etc. complete all as specified and/or as directed by engr-in-charge. 61 s&f pre- painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by engr-in-charge. 62 s&f pre- painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by engr-in-charge. 63 m&l for preperation of old woodensurfacesurface any descriptionover 10cm in width or girth and applying one coat of synthetic enamal paintall as specified and as directed complete all as specified and as directed. 64 m&l for preperation of new plastered wall surface of any description and applayng three coats of white wash complete all as specified and as directed. 65 s&f in repair 19mm dia mild steel, chromium plated curtain rods,withbrackets, end bulbs complete all as specified and/or directed by engr-in-charge. 66 s&f in repairs vitreous china squatting pan or orissa pattern580 x 440 mm white with integral foot rest (excluding cistern)with front or back inlet ant pattern including s trap of 125/110mm bore, including bedding with pcc 1:2:4, type b-i (using 20 mm graded crushed stone aggregate) complete all as specified and/or directed by engr-in-charge. 67 taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and/or directed by engr-in-charge. 68 m&l for pvc (swr) pipe single socketed, 110mm soil, waste and rain water drainage pipeslaid in trenches and jointed all as specified. 69 s&f in pvc (swr) swr 75 mm bore, single socketed in any length with rubber ring joints using solvent as per manufacture instruction, laid in trenches or in floors complete all as specified and directed by engr-in-charge. 70 s&f pvc (swr) vent cowl of 75mm bore, complete all as specified and as directed. 71 s&f 75 mm dia pvc (swr) bend any radius, complete all as specified and as directed. 72 m&l for pcc 1:4:8, type d-2 (using 40mm graded stone aggerate) bed to drain pipe incl packing under and haunching against side after they are laid and tested up to 110mm dia pipe, complete all as specified and/or directed by engr-in-charge. 73 m&l for precast cement concrete 1:2:4 type b1 (20mm graded aggregate) in landings, cover slabs (for manholes etc.), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, set in cm 1:6, complete all as specified and/or as directed by engr-in-charge. 74 s&f in repair 1200mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. 75 m&l for excavating in postholes (or similar holes) each not exc. 0.5 cum in hard/dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm. complete all as specified and directed. 76 m&l for pcc 1:3:6, type c-2 (using 40mm graded crushed stone aggregate) as in lean concrete, or mass concrete, foundation filling etc., complete all as specified and/or as directed by engr-in-charge. 77 material & labour walling of random rubble stone, uncoursed, masonry, well bonded, laid dryin retaining walls abutments and similar work all as specified and directed. 78 m&l for reinforced cement concrete (nominal mix) 1:2:4 type b1 (20mm graded aggregate) as in slabs supported of walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc. complete all as specified and/or as directed by engr-in-charge. 79 demolition of bricks (laid flat or on edge) or interlocking tiles in floors, channels, kerbes, aprons, etc laid dry of laid dry and pointed. 80 m & l for 100mm pcc 1:4:8 type d-2 using 40mm graded aggregate as in sub base complete all as specified and/or as directed by engr-in-charge. 81 m&l machine pressed precast concrete interlocking paver block any shape and size polished with grey cement and pigment confirming to is 15658-2006 of 60 mm thickiness m-35 grade complete all as specified and as directed by engr-in-charge.. 82 m&l sand filling under floors in foundations and for laying interlocking paver blocks including watering and consolidation complete all as specified and as directed by engr-in-charge. 83 taking down carefully copper/aluminium point wiring (light, fan, socket and power point) including complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as specified and directed by engr-in-charge. 84 point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded pvc insulated and unsheathed 1100 volts cable drawn through & including pvc casing & caping with standard accessories such as elbows, tees, junctions etc. and pvc moulded terminal box with top cover of including pvc insulated unsheathed solid 1.5 sqmm copper conductor cable as continuous earth lead complete all as specified and/or directed by engr-in-charge for the followings:- 85 one light/exhaust fan point controlled by one way switch. 86 one switch socket outlet 6 amps, 230 volts point on same board. 87 one switch socket outlet 6 amps, 230 volts point on independent board. 88 all as per srl item no 84 above, but using cables 4 sq mm size. 89 s&f switch piano flush button single pole 6 amps 230 volts one way complete all as specified and/or directed by engr-in-charge. 90 s&f switch socket outlet 2 in 1, 5 pin, 6 amps flush type 230 volts complete all as specified and/or as directed by engr-in-charge. 91 s&f switch socket combination outlet multi purpose 3/5 pin 6 amps and 16 amps 230 volts complete all as specified and/or directed by engr-in-charge. 92 s&f ceiling rose, surface bakelite three terminals complete all as specified and/or directed by engr-in-charge. 93 s&f inreplacement of sheet metal enclosure for dbs double door when mcbs to be used single pole & neutral 240 volts 12 ways complete all as specified and/or directed by engr-in-charge. 94 s&f inreplacement of sheet metal enclosure for dbs double door when mcbs to be used single pole & neutral 240 volts 04 ways complete all as specified and/or directed by engr-in-charge. 95 s&f mcb spn 63 amp 240 volts ac isi marked complete all as specified and/or directed by engr-in-charge. 96 s&f mcb sp 6-32 amps. 240 volts50 hz complete all as specified and/or directed by engr-in-charge. 97 supply and laying of xlpe insulated, armoured, heavy duty electric cables with stranded aluminium conductor rating 1100 volts grade of size 16 sqmm 4 core laid in trenches of passing through pipes ducts or fixed to walls / poles complete all as specified and directed. 98 supply and laying of xlpe insulated, armoured, heavy duty electric cables with stranded aluminium conductor rating 1100 volts grade of size 25 sqmm 4 core laid in trenches of passing through pipes ducts or fixed to walls / poles complete all as specified and directed. 99 supply and fix led light fitting mirror type with high output diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed . 100 supply and fix in replacement led street light fitting 70 watt 230 v ac outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65/66 protection, including connecting up with pvc insulated copper conductor cable 1.5 sqmm, 3 core as required and 40mm bore light grade gi tube mounting bracket of 1.5 metre in lenght complete. 101 s&f in replacement led light fitting 1x9w/1x10w bulkheadluminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and/or directed by engr-in-charge. 102 s&f in replacement led light fitting 1x20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and/or as directed by engr-in-charge. 103 excavation in tenches, not exc. 1.5m wide and not exc. 1.5 m in depth, for foundation, etc. or for laying ug cable in trenches not exc. 10 sqm on plan and not exc. 1.5m in depth in hard soil and getting out all as specified and directed by engr-in-charge. 104 returning, filling in (soil), including spreading, levelling, watering and well ramming in layers not exc. 25 cm, complete all as specified and directed by engr-in-charge. 105 removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified and directed by engr-in-charge. 106 m&l for sand cushioning to underground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of ssr part-i, complete all as specified and directed by engr-in-charge.note : punned thickness of 18 cm will be measured and paid seperately. 107 supply & laying of factory made, machine pressed, unreinforced, precast concrete cable cover lv type-1 flat size 250mm x 150mm x 40mm, complete all as specified and directed. 108 laying only factory made, machine pressed, unreinforced, precast concrete cable cover lv type-1 flat size 250mm x 150mm x 40mm, complete all as specified and directed. 109 m&l for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and including 4 mm dia gi wire as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate no 3 of mes ssr part i and testing on completion including excavation and earth work in any type of soil, pcc (1:3:6) type c1 chamber, ms frame and cover 6 mm thick in cement concrete (1:2:4) type b1 reinforced with welded steel wire fabric or xpm (weight not less than 4 kg per sqm) with cast iron frame, funnel with wire mesh, gi watering pipe 20mm dia medium grade and lugs complete all as specified and/or as directed by engr-in-charge.