tender for annual plan-kmbp 2025-26 148/26-cdpo office rennovation-general civil work - building maintenance 2 15.23.1:dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.for thickness of tiles 10 mm to 25 mm 3 15.2.2:demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in-charge.nominal concrete 1:4:8 or leaner mix ( including equivalent design mix) 4 2.8.1:earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil 5 5.1.2:providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) 6 4.1.8:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 7 50.6.2.2:solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to is 2185 part i of 1979 for super structure up to floor two level with thickness 15cm in : cm 1:6 ( 1 cement : 6 coarse sand) etc complete 8 5.3:reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15°landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (zone iii)derived from natural sources: 3 graded stone aggregate 20 mm nominal sizederived from natural sources). 9 5.22.6:steel reinforcement for r.c.c work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelthermo - mechanically treated bars of grade fe-500d or more 10 5.9.5:centering and shuttering including strutting, etc. and removal of form for:lintels, beams, plinth beams, girders bressumers and cantilevers 11 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 12 od228941/2025-2026:providing and laying vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. size of tile 600x600 mm 13 11.41a.3.1: providing and laying vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer)with water absorption less than 0.08% and conforming to is:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)jointing with grey cement slurry @3.3 kg/sqm including grouting thejoints with white cement and matching pigments etc. the tiles must be cut with the zero chipping diamond cutter only .laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.glazed vitrified tiles matt/antiskid finish of size size of tile600 x 600 mm 14 17.2.1:providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:w.c. pan with isi marked white solid plastic seat and lid 15 50.17.1.5:supplying and fixing cp health faucet superior quality ( jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site engineer-in-charge. 16 od228946/2025-2026:od1278040/2021_2022 :providing and fixing factory made pvc door including cost of all fittings, labour charges etc complete (approved data of ce lsgd vide circular dated 18.08.2016) od-11, dsr 2016 1.4902 dtd 05.06.2017 17 17.7.3:providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:white vitreous china wash basin size 550x400 mm with a pair of 15 mm c.p. brass pillar taps 18 50.18.9.20.1:providing and fixing pvc moulded fittings/ accessories for rigid pvc pipes, including jointing with pvc solvent cement - 63 mm dia elbow 19 50.18.9.7.1:providing and fixing pvc pipes includings of pipes with one step pvc solvent cement, trenching refilling & testing of joints complete as per direction of engineer in charge. 63 mm dia 6kgf/cm2 20 50.18.9.9.2:providing and fixing pvc pipes includes joints of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge. 110 mm dia 4 kg/cm2 21 13.88:removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 22 13.43.1:applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:water thinnable cement primer 23 13.98.1:wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:one or more coats on old work 24 13.60.1:wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:two or more coats on new work 25 50.9.11.1:providing and fixing thomson multi wood board or equivalent make paneling 12 mm thick, to frame, backing or studding with screws etc. complete ( frames, backing or studding to be paid separately) as per the direction of site engineer-in-charge. 26 50.9.11.2:providing and fixing thomson multi wood board or equivalent make paneling 18 mm thick, to frame, backing or studding with screws etc. complete (frames, backing or studding to be paid separately)as per the direction of site engineer-in-charge. 27 21.1.1.1:providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionanodised aluminium (anodised transparent or dyed to required shade according to is : 1868, minimum anodic coating of grade ac 15) 28 21.3.2:providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer - in -charge. ( cost of aluminium snap beading shall be paid in basic item):with float glass panes of 5.50 mm thickness(weight not less than 12.50 kg/sqm) 29 21.2.1:providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is : 12823 grade i type ii, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer - in- charge.pre-laminated particle board with decorative lamination on one side and balancing lamination on other side 30 od228972/2025-2026:supplying ansupplying and fixing ferrocement slab for cuboardd fixing ferrocement slab for cuboard 31 10.25.2:item shifted to sub head 14 as item 14.73item shifted to head 14 as item 14.74steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 32 11.41.2:providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.size of tile 600 x 600 mm. 33 15.28.1:dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :g.s. sheet 34 10.16.1:steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.hot finished welded type tubes 35 12.50:providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer-in-charge. the sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 36 13.99.1:painting with synthetic enamel paint of approved brand and manufacture ofrequired colour to give an even shade :one or more coats on old work 37 50.12.4.2:providing and fixing false ceiling with 7.5 mm thick pvc wooden grains panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete ( aluminium frame work shall be paid separately) 38 21.5:providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to is : 733 in frames of false ceiling including aluminium angle cleats with necessary c.p brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to g.i level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the engineer-in-charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ). 39 11.20.4:chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).ordinary cement without any pigment 40 14.5.1:renewing glass panes, with putty and nails wherever necessary including racking out the old putty :float glass panes of thickness 4 mm (weight not less than 10kg/sqm)