tender for periodical services at n area under ge chandigarh.; 1 taking down cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by engineer-in-charge. 2 demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) asin roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by engineer-in-charge. 3 dismantling of cast iron pipe/ pvc drain pipes/pvc (swr) pipe etc, 110mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed. 4 dismantling of cast iron pipe/ pvc drain pipes/pvc (swr) pipe etc, 75mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed. 5 hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones (upto 4th storey of building) completeall as specified and directed by engr-in-charge. 6 installation of rebar by using hilti hammer drill with carbide drill bit,chemical dispensing gun for inserting re-500v3 chemical upto minimum depth of (10 x dia of bar ) as in chajja,beam,lintel,column slab and parapet at any height before inserting an anchor bar.hole must be free from dust debris,water,oil grease (upto 4th storey of building) complete all as per manufacturers instructions.note :- (i) reinforcement shall be measured and paid separately. (ii) rates are inclusive of form work and safety measures.(iii) dia of bar 10/12 mm 7 reinforced cement concretenominal mix ( 1:2:4) using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, chajjas, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete including formwork complete all as specified and directed by engineer-in-charge. 8 tmt steel bars 10mm dia and over, of grade fe-500d cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by engineer-in-charge. 9 use & waste of formwork to chullah hoods,chajjas,troughs and similar item includind edges etc; complete all as specified and directed by engineer-in-charge. 10 rendering 10 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by engineer-in-charge. 11 rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces in two layersmixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, (upto 4th storey of building) complete all as specified and directed by engineer-in-charge. note: water proofing compound shall be measured and paid separately. 12 supply only liquid water proofing comound isi marked complete all as specified and directed. 13 rendering 10 mm thick in cement mortar 1:3as in ceiling/soffits of slabs/chajja/ sunshade finishing the plastered surface even & smooth without using extra cement etccomplete all as specified and directed by engineer-in-charge. 14 material & labour for applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and a priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces on wall, incl necessary preparation works, (upto 4th storey of building) complete all as specified and as directed. 15 preparation of old plastered surfaces of walls and applying two coats of plastic emulsion paint on walls over and including a coat of primer and 2mm thick wall care putty (upto 4th storey of building) including preparation of surface complete all as specified and directed. 16 preparation ofplastered or unplastered new surfaces of ceilingsand applyingtwo coats of white wash including preparation of surface complete all as specified and directed by engineer-in-charge. 17 preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of chalk whiteningover 1mm thick wall care putty including preparation of surface complete all as specified and directed. 18 complete removal of old plastered surfaces of walls and applying two coats of oil bound distemper on walls over and including one coat of chalk whitening and 1 mm wall care putyincluding preparation of surface (upto 4th story of bldg), complete all as specified and directed. 19 preparation of old plastered or un-plastered surfacesof ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on ceilings/ old decorated surfacescomplete all as specified and directed by engineer-in-charge. 20 preparation of old plastered or un-plastered surfacesof walls etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coats of white wash on walls/ old decorated surfaces(upto 4th storey of building), complete all as specified and directed by engineer-in-charge. 21 preparation of old plastered surfaces of wall and applying one coat of cement base paint on walls including preparation of surface (upto 4th storey of building) complete all as specified and directed. 22 preparation of old plastered surfaces of wall and applying two coats of cement base paint over and including a coat of primer over 1mm thick wall care putty on walls including preparation of surface (upto 4th storey of building) complete all as specified and directed. 23 material & labour for applying two coat of 100% premium acrylic emulsion paint having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including 1mm thick putty and a priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces (upto 3rd story bldg) including complete removal of existing treatment from wall surfaces including rubbing with sand paper & scrubbing down with water etc (upto 4th storey of building), complete all as specified and as directed. 24 preparation of old plastered surfaces of wallsand applying one coat of oil bound distemper on walls (upto 4th storey of building),complete all as specified and directed. 25 preparation of old plastered surfaces of ceilingand applying one coat of oil bound distemper on ceiling, complete all as specified and directed. 26 m&l for one coat of synthetic enamel paint over old painted wooden or wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified. 27 m&l for one coat of synthetic enamel paint over old painted steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified. 28 m&l for one coat of synthetic enamel paint over old painted steel & iron surfaces of any description, not otherwise described, not exc 10 cm in width or girth, including preparation of surfaces complete all as specified. 29 m&l for writing letters or figures (block, roman, italic or indian) n exc 30 cm high with thick paint to stand out solidly and boldly without showing signs of brush marks complete all as directed 30 sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clipsusing silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 sq. mtr in each pane (upto 4th storey of building) complete all as specified and directed by engineer-in-charge. 31 sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clipsusing silicon for fixing of glass in addition to glazing putty, in squares exceeding 0.5 sq. mtr in each pane (upto 4th storey of building) complete all as specified and directed by engineer-in-charge. 32 4 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using silicon for fixing of glass in addition to glazing putty (upto 4th storey of building) complete all as specified and directed by engineer-in-charge. 33 110 mm bore, pvc (swr) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including ms clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by engineer-in-charge. 34 75 mm bore, pvc (swr) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including ms clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by engineer-in-charge. 35 pvc(swr)bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by engineer-in-charge. 36 pvc(swr)bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by engineer-in-charge. 37 note: for the purpose of arriving at lumpsum amount, the amount of credit schedule i.e sch a section ii (i.e rs 10,450.00 shall be deducted from the total amount arrived. 38 total of schedule a rs.