supply testing installation commissioning and demonstration of hand tools instruments equipment and machineries of electrician and turner trade at iti jalpaiguri , supply of short fall of electrician trade course , relay- reverse current, 16a, 440v , relay- over current, 16a, 440v , relay-under voltage, 360v-440v , pin type insulators including hardware fitting , shackle type insulators including hardware fitting , egg type insulators including hardware fitting , suspension type insulators including hardware fitting , laboratory type induction coil, 1000 w , knife switch dpdt fitted with fuse terminals, 16 amp , knife switch tpdt fitted with fuse terminals, 16 amp/ 440 v , earth plate, 60cm x 60cm x 3.15mm copper plate , earth electrode,primaryelectrode2100x28x3.25mm secondary cu strip 20x5mm , mccb, 100amps, triple pole , twisted pair cable, 1 mtr , non-metallic sheathed cable , 1 mtr , underground feeder cable , 1 mtr , ribbon cable , 1 mtr , metallic sheathed cable, 1 mtr , multi-conductor cable, 1 mtr , coaxial cable , 1 mtr , direct-buried cable, 1 mtr , rheostat(sliding type), 0-25ohm,2amp , rheostat(sliding type), 0- 300ohm, 2 amp , rheostat(sliding type), 0-1ohm, 10amp , rheostat(sliding type), 0-10ohm,5amp , bus bar with brackets, 1 mtr each , rcc pole with accessories (ms angle iron, ‘c’ clamp, stay insulator etc.) and materials, 6 mtrs , digital multi meter, dc 200mv -1000v,0 – 10a & ac 200mv- 750v , 0-10a, resistance 0-20 m? and 3 1/2 digit , digital wattmeter, 230 v, 1 kw, 50 hz , magnetic flux meter, 0-500 tesla , meggar, analog-500v , ac starters:- resistance type starter, for a.c motors of 2 to 5 h.p. , ac starters:- star delta starter–semi automatic, for a.c motors of 2 to 5 h.p. , ac starters:- star delta starter- soft starter, for a.c motors of 2 to 5 h.p. , oscilloscope dual trace, 20 mhz , temperature controlled soldering iron, 50-watt, 230 volt , immersion heater,1500watt,240v , motor pump set,1hp,1phase,240v , oil testing kit, oil testing kit, 230v,singlephase50 hz 60 va output 0-60 kv variable , inverter with battery, 1 kva with 12 v battery input- 12 volt dc, output- 220 volt ac , dc power supply, 0 - 30 v, 5 a , potential transformer,415v,50hz,ptratio,440v/110v, 10 va , ac phase-wound slip ring motor with starter switch, 5hp,440v,3phase,50hz , universal motor with starter/switch, 240v,50hz,1 hp , three phase transformer, shell type oil cooled with delta/ star, 3 kva , 415/240 v, 50 hz , diesel generator set with change over switch, over current breaker and water/ air-cooled with armature, star-delta connections ac 3 phase ,7.5 kva, 415 volt or higher rating , used dc generators-series type for overhauling practice , used dc generators- shunt type for overhauling practice , used dc generators -compound type for overhauling practice , ceiling fan coil winding machine, 250v, 50 hz, 1-?, with speed control , shaded pole motor, fractional hp, 240v,50 hz , smart meter,1phase-smart energy meter , smart meter,3phase-smartenergymeter , ev charger, 3phase input , ev charger (home), 1phase input , supply of short fall for turner trade course , surface plate - granite, 1000 x 1000 mm with stand and cover , marking table (ci), 120 x 120 cm with stand and cover , micrometer inside, upto 25 to 50 mm, least count 0.01 mm with nabl accrediated lab certificate , vernier caliper outside, inside and depth, 200mm / 8 inch with metric and inch scale (lc=0.02mm) with nabl accrediated lab certificate , dial vernier caliper, 200mm , least count 0.05mm with nabl accrediated lab certificate , vernier bevel protractor, 300mm blade with nabl accrediated lab certificate , vernier micrometer, 0- 25 mm o/s lc=0.001mm with nabl accrediated lab certificate , gauge feeler, thickness - 0.05mm to 0.3 mm by 0.05 mm-13 leaves , gauge feeler, thickness -0.4mm to 1mm by 0.1mm -13 leaves , gauge - radius set, 1mm to 25mm by 0.5mm , drill angle gauge, 45 degree, 55 degree, 90 degree , magnifying glass, 75mm with magnifying factor 10x , plain ringgauge, 12,16,20,25,30,32,36,40,45,50 mm , plainplug gauge, 12,16,20,25,30,32,36,40,45,50 mm , tap &die , ba no 0 to 10 in a box , tap &die set, metric - 3 to 24 mm , tap &die , bsf upto 1 inch , tap &die, bsw upto 1 inch , angle plate, adjustable - 150 x 175 x 250 mm , tool makers button , hand chaser with handle, m-12 & m-16 (external) , hand chaser with handle, m-12 & m-16 (internal)