equipments for edc lab , equipments , single phase ac circuit kit for voltage,current and power measurement specification: measurement of power by using various loads, analog voltmeter 0-300 v ac panel mounted, analog ammeter 0-5a ac panel mounted, analog wattmeter 1.5kw ac panel mounted, single phase digital power monitor to measure power, single phase ac lamp load 230v/5a 1 kw, panel enclosure with hylam front panel with input/outputterminal outlets. experiments to be conducted 1. to conduct an experiment to measure voltage, current and power in single phase ac circuit by usingvolt meter,ammeter and wattmeter respectively for different loads. 2. to do the same experiment by replacing abovemeters with single digital power monitor. , mcb and elcb training kit specifications:single pole mcb 2-5amps, two pole elcb 30ma, lamp load single phase 5amps, panel enclosure and terminal outlets, experiment to be performed: 1. demonstration and testing of mcb and elcb by short circuit test, earth fault test and load test by using lamp load 2. connect elcb with lamp load and test the tripping operation for earth fault. , single phase induction motor kit for load test specification: single phase induction motor 1hp, 230v, ac & 1500 rpm with loading arrangement ( kirloskar / equivalent) - 1 no,, voltmeter (0-300) vac - 96x96 mm with input terminals –1 no, ammeter (0-10) a ac- 96x96 mm with input terminals –1 no, wattmeter 2kw - 96x96mm with input terminals –1no, power factor meter, 96x96mm with input terminals –1no, auto transformer 0-300 v 1f variac –1 no, mcb 2 pole 40a/230vac–1 no, digital rpm indicator with proximity sensor – 1 no, aluminium brake drum, dia 230mm – 1 no, springbalance(0-25)kg–02 nos, circuit diagram to be printed on front panel, with instruments connecting terminals, motor and loading arrangement mounted on a rigid channel frame with anti-vibration mounting pads with m12x1.5 bolt & nut - 85mm dia/- 4 nos, mild steel powder coated electrical panel table set up, experiments to be conducted to conduct load test and to draw its characteristics curves as follows 1. load current vs torque 2. load current vs speed 3. load current vs efficiency , 3 phase induction motor kit quarter cut section model: to show all the parts of induction motor are displayed with stator core and rotor core cut for showing the rotor bars etc. , dc shunt motor kit for load test specification: dc shunt motor 1hp, 230v, dc & 1500 rpm with loading arrangement ( kirloskar / equivalent)- 1 no, ammeter (0-30)a - 1no,ammeter (0-2a) - 1 no, voltmeter (0-300)v - 1no, rheostat 350o (1.5a) - 1no, digital rpm indicator with proximity sensor - 1 no, three-point starter 220 v / 5hp - 1no, connecting wires 2.5 sq.mm red, black each 5 meter rectifier in built with the kit , aluminium brake drum, dia 230mm, spring balance (0-25) kg – 02 nos, 2 pole dc mcb 30a (1no), circuit diagram to be printed on front panel, with instruments connecting terminals, motor and loading arrangement mounted on a rigid channel frame with anti-vibration mounting pads with m12x1.5 bolt & nut - 85mm dia/- 4 nos, mild steel powder coated electrical panel table set up, experiments to be conducted: to conduct load test and to draw its characteristics curves as follows 1. load current vs torque 2. load current vs speed 3. load current vs efficiency , dc shuntmotor kit for speed control specification: dc shunt motor 1 hp, 230v, dc & 1500 rpm without loading arrangement ( kirloskar / equivalent) - 1 no, ammeter (0-2) a mc - 2nos, voltmeter (0-300) v mc - 1no, 2 pole dc mcb 30a - 1nos, tachometer digital / sensor –1 no, three - point starter-1no, rheostat 100 o 5a - 1no, rheostat350?1.5a–1nos, connecting wires 2.5 sq.mm red, black each 5 meter, rectifier inbuilt with the kit , circuit diagram to be printed on front panel, with instruments connecting terminals, motor and loading arrangement mounted on a rigid channel frame with anti-vibration mounting pads with m12x1.5 bolt & nut - 85mm dia/- 4 nos, mild steel powder coated electrical panel table set up. experimentsto be conducted: to run and study the speed for the given dc shunt motor by armature voltage control and field control. , stepper motor drive kit specification torque: 0.5kgm2/s2 input: 220v ac angle: 0-360° direction: forward/reverse drive: lm2907u run step direction clock input & step clock pulse speed variable system metal enclosures components on pcb system motorvolts: 5-12v ddc(2a) , serve motor drive kit specification: ac servo motor system, input: 220vac, type: closed loop system, angle: 0-360°, set & actual position, microcontroller based set position with servo feedback pulse , bldc motor kit specification: 48v,750w bldc motor without loading arrangement, mecos mp 48 model 48x96 panel dc voltmeter – 04 nos, all input & output are terminals connected to controllerby terminals experiments, testing points, firing angle or triggering angle of dc motor, fwd/rev switch output, hall sensor output, brake switch output, high brake & low brake output, armature & mosfet test, accelerator or potentiometer test, motor and loading arrangement mounted on a rigid channel frame with anti vibration mountings pads with m12x1.5 bolt & nut - 85mm dia- 4 nos, mild steel powder coated electrical panel table set up. , half wave , full wave and bridge rectifier kit specification: input: 220vac, output: 12v dc/1amps, halfwaverectifier, bridge rectifier, full wave rectifier, filter connections, with testing points, experimentsto be conducted: to study half wave rectifier circuit , full wave rectifier circuit and bridge rectifier circuit with and without filter , digital trainer kit specification: built-in power supply dc+5v@ 500 ma, bread boards, 8 logic input switches with green led display, 8 logic output red led display, required numbers of patch cords