annual maintenance of hsvp building in sector-1 to 21, panchkula (providing and fixing of door, window, chowkhat and othersanitary items complete in all respect staff quarter at t/well no. 03, sector-12, panchkula).- 1 12.19.1.1.1:- providing and fixing wire gauge shutters using galvanized m.s. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters with isi marked m.s. pressed butt hinges bright finished of required size second class teak wood 2 12.10.1.2:- providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws. second class teak wood 30 mm thick 3 30.54.2:- renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5 mm (weight not less than 12.5 kg/sqm) 4 12.36.1:- providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including isi marked stainless steel butt hinges with necessary screws 5 30.53.1.1:- replacing and fixing 25 mm thick shutters for cup board etc i/c disposal of dismantled shutters, if any: 1.1 panelled or panelled & glazed shutters : superior class teak wood including nickel plated bright finished m.s. piano hinges with necessary screws. 6 13.22.1:- supply and fixing windows frames (chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 0.58mm thick galvanized sheet (base steel as per is 513) with zinc of 120 gm/sqm steel sheet pre coated (as per approved colour) with polyester paint of 12-16 microns thickness under coat of epoxy primer and back coat with alkyd backer of 5-7 microns, total sheet thickness with coating 0.58mm of approved shade, weld less corner assembly with brackets and screws, fixed in position by means of pvc and metal hold fastener with pvc cap complete in all respects as per drawing, design, specification and entire satisfaction of engineer-in-charge. 1 windows outer frame of size 72mm x 55mm and central mullion 72mm x 50mm with double rebate 7 18.26:- providing and fixing factory made kitchen cabinet shutter/partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (single extruded) having density 600 kg/cum and laminated on both side by laminate sheet/pvc foil lamination. the exposed edges shall be sealed with pvc edge beading of same shade and colour. the shutter shall be fire retardant having necessary screw holding capacity. shutter shall be fixed to frame using approved hinges with necessary stainless steel screws, all complete as per direction of engineer-in-charge. 8 12.25.2.1:- providing and fixing 25 mm thick shutters for cup board etc. : glazed shutters : second class teak wood including isi marked anodized aluminium butt hinges with necessary screws 9 30.22:- removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 10 11.58:- providing and applying two coats white cement based putty of approvedbrand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete 11 30.27.1:- wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: 1 one or more coats on old work 12 30.37.2:- finishing walls with acrylic smooth exterior paint of required shade : old work (one or more coat applied @ 0.90 litre/10 sqm). 13 30.28.1:- painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 1 one or more coats on old work 14 30.10.1:- replacing sand stone slabs in roofing, laid in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary repairs and cement pointing with same mortar complete, including disposal of rubbish to dumping ground, all complete as per direction of engineer-in-charge. 1 red sand stone slabs 30 to 50 mm thick