tender for annual maintenance of staff quarters in sector-11, u/e panipat.repair and mtc. of staff quarter no. 123e (durga dass)complete in all respect and all other works contingent thereto.-- 1 [11.64.1]distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1. new work (two or more coats) over and including water thinnable priming coat with cement primer 2 [11.68.1]applying priming coat: 1. with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 3 [11.68.3]applying priming coat: 3. with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 4 [6.14.2]providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 2. 1:2:4 (1 cement : 2 coarse sand (zone-iii) : 4 graded stone aggregate 20 mm nominal size) 5 [11.94]finishing walls with textured exterior paint of required shade : 1. new work (two or more coats applied @ 3.28 litre/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm 6 [11.95]finishing walls with acrylic smooth exterior paint of required shade : 1. new work (two or more coat applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 7 [11.93]finishing walls with water proofing cement paint of required shade : 1. new work (two or more coats applied @ 3.84 kg/10 sqm) 8 [30.16.1]repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of engineer-in-charge. 1. with cement mortar 1:4 (1 cement : 4 fine sand) 9 [23.1.1.1]copper wiring in ms conduit (surface/recess) 1.1. wiring for light/fan/call bell point in 1.5 sqmm frls pvc insulated copper conductor cable in 1.6 mm thick ms conduit pipe. group a 10 [23.1.1.2]copper wiring in ms conduit (surface/recess) 1.2. wiring for light/fan/call bell point in 1.5 sqmm frls pvc insulated copper conductor cable in 1.6 mm thick ms conduit pipe. group b 11 [23.1.5.3]copper wiring in ms conduit (surface/recess) 5.3. wiring in ms conduit system for 3-pin 15amp. plug point by using 2 no 4 sqmm frls copper wire and 1 no 4 sqmm frls copper wire for earthling , including providing 1 no 15/16 amp 3/6 pin socket and 1 no 15/16 amp switch required ms box etc complete as required group c 12 [12.1.1.3]providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paidseparately). 1.3. kiln seasoned and chemically treated hollock wood 13 [12.9.7.1]providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 7.1. float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). 14 [12.20.1]providing and fixing wire gauge laminated veneer lumber shutters conforming to is : 14616, using galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm as per is :1568, for doors, windows and clerestory windows, including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws, as per directions of engineer-in-charge: (note:- butt hinges and necessary screws shall be paid separately) 1. 35 mm thick shutters 15 [12.36.1]providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 1. 35 mm thick including isi marked stainless steel butt hinges with necessary screws 16 [12.13.1]providing and fixing factory made laminated veneer lumber glazed shutter conforming to is: 14616, using 4 mm thick float glass panes for doors, windows and clerestory windows, including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws, all as per directions of engineer-in-charge (note:- butt hinges and necessary screws shall be paid separately) 1. 30 mm thick shutters 17 [22.39.1]providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete. 1. 10 litre capacity - white