total of 18 black spots on the identified pwd routes in the year 2022 in agra district ( badagaon, arnauta, kalal kheria, basai fatehabad road, tajview tiraha, targarh crossing, miyanpur, fatehpura tiraha, pathakpura, khilabali, syahipura, badagaon, thana garhi, garhi improvement work of jaha singh mod, khand chauraha, kanharpura pulia, derak bridge, abhaypura chauraha. - providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes. ( chp-24 si no.-2 morth-803 ( 8.13 ) 2 road marking with hot applied thermoplastic compound with reflectorlsing glass beads on bituminous surface. ( repeated / tranvers bar ) providing and laying of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads 0 ) 500 gms per sqm area, thickness of 5 mm is exclusive of surface applied glass beads as per irc:35-2015 the finished surface to be level, uniform and free from streaks and holes. 3 reflective raised pavement markers ( cat eye / road stud ) supply and fixing of raised pavement marker with made of plastic body of rpm / road stud shall be moulded from asa ( acrylic styrene acrylonitrile ) or hips ( high-lmoact polystyrene ) or acryloniitrite butadien styrene ( abs ) or any other suitable material approved by the engineer. the marker shall support a load of 13, 635 kg tested in accordance with astm d4280.the reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entring the lens face. lenses shall be mouled of methyl methecrylate conforming to astm d788 of equivalent. the slop or retro-reflecting surface shall preferably be 35+1-5 degree to base and the area of each retro -reflecting surface shall not be less than 13.00 sq.cm. the marker height shall not be less than 10 mm and shall not exceed 20 mm & width shall not exceed 130 mm. the base of the marker shall be flat within 1.3 mm all road studs shall be legibly marked with the name , trade or other means of identification of the manufacture. epoxy installations, excess adhesive around the edge of the marker, excess adhesive on the pavement and adhesive on the exposed surfaces of the markers shall be immediately removed. the contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel , to the engineer . in addition . a two year warranty for satisfactory infield performance of the finished road marker shall also be given by the contractor who carries out the work of fixing of reflective road markers. in case the markers are displaced , damaged . get worn out or lose their reflectivity compared to stipulated standards , the contractor would be required to replace all such markers within 15 days of the intimation from the engineer . at his own cost the rate shall include all materials, labour, t&p, transportation, installation and incidentals all complete as per direction of the engineer-in-charge. ( with shank ) 4 direction and place identification signs up to 0.90 sqm size boardproviding and erecting direction and place identification retro-reflectorised sign as per irc-67 made of high intensity grade sheeting the retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection. daytime colour and luminance, shrinkage, flexibility. liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international / govemment laboratory / institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad. alternatively, a certificate conforming to astm specification ( d4956-09 ) on artificial ccelerated weathering requirements from a reputed laboratory in india can be accepted provisionally. in such a situation, the employer i client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per irc 67:2012. legends , letters , numerals and borders etc should be as per morth specification no-801.3.7 . sheet fixed over aluminium sheeting .2 mm thick with area not exceeding 0.9 sqm.supported on a mild steel single angle iron post 75x75x6 mm firmly fixed to the ground by means of property designed foundation with m-15 grade cement concrete 45x45x60 cm., below ground level as per approved drawing. complete. ch-28 si no- 19 5 retro-reflectorised traffic sign as per irc-87-2012providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc :67-2012 made of high intensity grade sheeting type-iv vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete 45 cm x 45 cm x 60 cm. 60 cm below ground level as per approved drawing. the retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international / government laboratory / institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad. alternatively, a certificate conforming to astm specification ( 0 4956-09 ) on artificial accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally. in such a situation, the employer / client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per irc 67.2012. legends , letters , numerals and borders etc should be as per morth specification no-801.3.7 . proof of the same in form of government report shall be uploaded while quoting tender. ch-28 si no-.ii ) 60 cm equilateral tringle with diffinitation plate ( 20cm x 60cm ) 6 retro-reflectorised traffic sign as per irc-87-2012providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc :67-2012 made of high intensity grade sheeting type-iv vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete 45 cm x 45 cm x 60 cm. 60 cm below ground level as per approved drawing. the retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international / government laboratory / institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad. alternatively, a certificate conforming to astm specification ( 0 4956-09 ) on artificial accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally. in such a situation, the employer / client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per irc 67.2012. legends , letters , numerals and borders etc should be as per morth specification no-801.3.7 . proof of the same in form of government report shall be uploaded while quoting tender. ch-28 si noiii ) 60 cm circular with diffinitation plate ( 20cm x 60cm ) . 7 retro-reflectorised traffic sign as per irc-87-2012providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc :67-2012 made of high intensity grade sheeting type-iv vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete 45 cm x 45 cm x 60 cm. 60 cm below ground level as per approved drawing. the retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international / government laboratory / institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad. alternatively, a certificate conforming to astm specification ( 0 4956-09 ) on artificial accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally. in such a situation, the employer / client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per irc 67.2012. legends , letters , numerals and borders etc should be as per morth specification no-801.3.7 . proof of the same in form of government report shall be uploaded while quoting tender. ch-28 si no v ) 60 mm x 45 mm rectangular with diffinitation plate ( 20cm x 60cm ) 8 retro-reflectorised traffic sign as per irc-87-2012providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc :67-2012 made of high intensity grade sheeting type-iv vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete 45 cm x 45 cm x 60 cm. 60 cm below ground level as per approved drawing. the retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international / government laboratory / institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad. alternatively, a certificate conforming to astm specification ( 0 4956-09 ) on artificial accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally. in such a situation, the employer / client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per irc 67.2012. legends , letters , numerals and borders etc should be as per morth specification no-801.3.7 . proof of the same in form of government report shall be uploaded while quoting tender. ch-28 si no vii ) 90 cm high octagon 9 delineator supply & fixing of m s delineator made of mild steel with pure polyester powder coating with the minimum thickness of powder coating of not less than 40 micron for protection against corrosion the surface should be conceated so that there should not be any exposed surface without powder coating. alternatively, these metal guide poles can be concealed with thermoplastic body. the posts shall have ian ellipsoidal or circular design with the height of the pole shall be 800 to 900 mm above the ground with about 200 to 300 mm base which can be anchored onto the ground. mild steel guide poles shall conform to type xi sheeting specifications as per irc:67 and astm d4956 which would ensure to obtainl clear visibility of the road alignment during night time. the retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international / government laboratory / institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad. alternatively, a certificate conforming to astm specification ( d4956-09 ) on artificial accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally. in such a situation, the employer / client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per irc 67:2012 & proof of the same report shall be uploaded which quoting tender. the rate shall include all materials, labour. t&p, transportation, installation and incidentals all complete as per direction of the engineer•in-charge. ch-28 si ni-1 10 providing & applying tack coat with bitumen vg-10 using bitumen pressure distributor at the rate of 0.20 kg. / sqm. on the prepared primed granular / old painted surface, cleaned with air compressor, including all taxes, material, labour, t&p etc required for proper completion of the work. ( for bitumenous surface ) . 11 providing and laying bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder @ 5.4 % ofmix and filler, transporting the hot mix to work site laying with a hydrostatic paver finisher to the required grade, level and alingment, rolling with smooth wheeled bibratory and tendom rollers to achiev the desired compection as per morth specifiaction clause 509 complete all respects. grading-ii 12 note - 1- rates are inclusive of all taxes but excluding gst which shall be paid extra as applicable2- labour cess @ 1% will be deducted from contractors bill at the time of payment