tender for repairing works of electric crematorium with replacement of refractories and heating elements for the electric crematorium furnace no.1 & furnace no. 2, under katwa municipality up to 31/03/2025-- 1 roast bricks 2 fire tilesbrick no. 27 3 fire tilesbrick no. 29 4 angle bricks brick no. 88 5 ash bricksbrick no 16 to 24 6 air pocket brick brick no 100 7 air pocket brick brick no 101 8 brick no. 92 9 brick no. 93 10 insulation bricks 11 24 x 12 x 3 tiles 12 fire bricks is : 8 13 ash door bricks (small) 14 ash door bricks (big) 15 fire clay 16 ceramic fibre blanket 17 ceramic tube 18 heating elements coil 19 copper wire 10 swg with porcelain bit 20 brass connector for heating coil 21 supply, delivery at site and laying of 1.1 kv grade xlpe insulated pvc outer sheathed armoured alluminum cable conductor power cable of following size either through cable duct or through cable tray or through protection pipes incl end termination as required and as per technical specification.a) 3 ½ core x 35 sq. mm. (al.) 22 b) 3core x 6 sq mm (al) 23 c)termination of cable with necessary gland & socket 24 200amp tpn fuse switch unit fn type open/closed 25 100 amp tpn fuse switch unit fn type open/ closed 26 32 amp tpn fuse switch unit fn type open/ closed 27 32 amp-tpn isolator 28 16 amp. dp isolator (enclosed) 29 63 tpn contactor (l & t) ml 4 30 starter for motorl& t make 31 400 a hrc fuse base hn/ hq 32 200 a hrc fuse base hn/ hq 33 100 a hrc fuse base 34 63 a hrc fuse base 35 32 a hrc fuse base 36 16 a hrc fuse base 37 300 a porcellain fuse 38 63-100a hrc fuse 39 2a 32a fuse base 40 0-125a ammeter ae 4 x 4 41 0-15a ammeter ae 4 x 4 42 0-300 a ammeter ae 4 x 4 43 0-500 a volt meterae 4 x 4 44 temperature controller meter 45 300/5a current transformer 46 led indicating lamp 47 chrome allumina thermocouple 48 repairing and overhauling the front door assembly with s.s rod, grade 310 , ceramic blanket 128 density 1400 degree c temperature carrying etc. complete required including dismantling the damage items and restore. 49 shaft for door lifting gear 50 handle for door lifting 51 shaft for door operating handle 52 pulley for door operating 53 chain i) 1 x 3 mtr. 54 chain ii) 3/4 x 2.5 mtr 55 spring sets for door pressing to guide rail 56 trolley rollers 57 trolley pin 58 trolley bush 59 trolley socket 60 ash collection door hinge block 61 liver 62 bearing sets for blower motor fresh air 63 bearing sets for door handle shaft 64 handle pin for door lifting 65 sprocket for door lifting gear 66 counter weight 67 ash collection spade and hooks 68 ash collection tray stainless steel 69 sprocket for door operating handle 70 turn buckle for door lifting chain 71 painting of furnace unit and charging trolley by using aluminum paints before applying red oxide. 72 painting of pollution control unit by using aluminum paints before applying red oxide. 73 fresh air blower 74 4mm m.s sheet 75 m.s angle 50mm x50mm 76 m.s angle 25mm x25mm 77 nut, bolt 5/8 x2” with washer 78 nut, bolt ½” x2” with washer 79 nut, bolt 3/8 x2” with washer 80 flue exhaust blower with ss impeller (id fan) 81 induced draught fan for fresh air (fd fan) 82 recirculation pump 83 10 h.p/7.5 h.p. , 3 ph, 2900 rpm -abb make and accessories 84 2 h.p,3 ph, 2900 rpm -abb make, and accessories 85 spray tower unit for scrubber 86 spray tower unit for ventury 87 m.s flange 88 30 mtr height chimney painting with scrubbing thoroughly and applying 2 coat red oxide and two coat aluminum paints 89 10 h.p. motor 90 7.5 hp motor 91 2 h.p. motor 92 2 h.p mono block pump motor 93 delivery charges per trip