supply and construction of 06 x small arms permanent defence-- 1 rcc permanent defence (small arms) 2 excavating over areas, n exc 1.5 m deep and getting out soft /loose soil all as specified and as directed. 3 excavating over areas, exc 1.5 m deep ,n exc 3.0 m deep and getting out soft /loose soil all as specified and as directed. 4 m & l cement concrete75 mm thick in fdn type b-2, 1:2:4 (40 mm graded aggregate) complete as specified and as directed. 5 m & l for rcc m-20 (nominal mix) type b1 1:2:4 (20 mm graded aggregate) in foundation, including rafts, footing, foundation beams, bases for column etc complete all as specified and directed. 6 m & l formwork to sides of rough finished flat surface of concrete foundations, footings, raft, bases of colums, plinth beams and simillar work vertical or to batter with cover blocks all as specified and as directed. 7 m & l for rcc m-20 (nominal mix) type b1 1:2:4 (20 mm graded aggregate) in walls, retaining walls, basement walls, and the like, any thickness, above top of footings, including attached pilasters and buttresses all as specified and directed. 8 m & l formwork to rough finished flat surface of walls, pillars, posts, struts, piers, columns and stanchions with cover blocks all as specified anddirected. 9 m & l for rcc m-20 (nominal mix) type b1 1:2:4 (20 mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed. 10 m & l formwork to rough finished flat surface soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work exceeding 200mm thick (horizontal or sloping) with cover blocks all as specified and as directed. 11 m & l formwork to edges of rough finished flat surfaces ofroofsexc 20 cm wide with cover blocks all as specified and as directed. 12 m & l brick work with subclass b brickin parapet wall in cm 1:4 all as specified and as directed. 13 m & l cement concrete type b1, 1:2:4, 20 mm graded aggregate) 50 mm thickin coping complete all as specified and as directed. 14 m & l for mild steel tmt bar 6 to 8 mmn dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with andincluding mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed 15 m & l for mild steel tmt bar 12 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with andincluding mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed 16 m & l for mild steel tmt bar 20 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with andincluding mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed 17 m & l rendering 15 mm thick on wall in cm 1:4 on fair faces of bricks work or concrete surfaces complete all as specified and as directed. 18 m&l integral water proofing compund 19 m & l cement concrete75 mm thick in flooring type b-2, 1:2:4 (40 mm graded aggregate) complete as specified and as directed. 20 m&lfor 75mm dia pvc (swr) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. 21 s&f formild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared forhanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing fe 410 -w (gde- e- 250) quality- a complete all as specified and directed. make - sail/tata/jsw/jindal/rinl. 22 s&f for 125mm butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed. 23 s&f for 300mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed ® complete all as specified and directed. 24 m& l for preparation of new plastered surfaces of wall and applying two coats of synthetic enamel paint of apporeved colour and patternover a coat of cement based primer complete all as specified anddirected. 25 m & l priming surfaces and applying bitumen as a primer in base of app membrance completed all as specified and as directed 26 m & l app based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than150 gms/sqm) land on primed surface byforced application completed all as specified. 27 m& l for preparation of new ms surfaces of door and loop hole and applying two coats of synthetic enamel paint of approved colour and patternover a coat of red oxide primer complete all as specified anddirected. 28 supply and fixing in wall pvc (swr) pipe 110 mm dia for rainwater drainage complete all as specified anddirected. 29 supply and fixing in trenches 80 mm dia gi pipe with all fittings complete all as specified anddirected. 30 m&l for filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm, complete all as specified and directed 31 m & l cement concretein stairs in pcc 1:8:16 (40 mm graded aggregate) complete all as specified and as directed. 32 ms sun shades made of 0.60 mm ppgi sheet reinforced with isa frame 35 x 35 x 5 mmand ms flat 35 x 3 mm will be providedloop hole opening and door.the minimum projection of sun shade shall be 450 mm and 300 mm wide than the opening sun shade shall be fixed in 20 degree downword slope and fixed with 8 nos 12 mm dia 150 mm long nut & bolt in rcc wall including two coats of syenthetic enamel paint of apporevedcolour and pattern complete all as specified anddirected. make : sail/tata/jsw.