supply of austenitic steel coilaustenitic steel coil, austenitic steel coil 1.25x1250mm., as per drawing / specification: rdso spec no.c- k201, grade x5crni1810 ( 304 ) table 1&2, heat treatment condition 2b as per table-5, coil id 450-650mm, od 1000-1300mm, coil weight 5-10 tonnes., packing instruction: stainless steel ( austenitic & ferritic steel coils etc. ) : the coil shall be protected in reasonably good condition to withstand normal handling hazard during transit with the following provisions as the barest minimum: i ) coil should be wrapped with a layer of water proof paper throughout the whole length. ii ) coil should be wrapped with a layer of biodegradable sheet. iii ) outer & inner of coil should be wrapped with gi sheet. iv ) side of the coil should be covered with card board sheet. v ) after this whole coil should be wrapped with biodegradable plastic sheet of suitable thickness. vi ) the inner edge of the coil should be protected by gi ring , followed by another iron ring. vii ) outer edge of the coil should be wrapped with gi ring. viii ) coil should be securely strapped with minimum 5 steel bands through the eyes of the coil and minimum 3 steel bands on the circumference of the eye. ix ) whole coil should be mounted on wooden blocks for easy lifting / stacking. , austinitic steel sheet 3x1250x3300 mm., as per drawing / specification: rdso spec no.c-k201, grade x5crni1810 table 1&2, heat treatment condition 2b as per table-5., packing instruction: as per standard packing. it should be ensured that item should not rub during transportation. the item should be packed with adequate strength. transit damage , if any , shall be at the cost of supplier. , austenitic steel coil 2x1250mm., as per drawing / specification: rdso spec no.c-k201 grade x5crni1810 ( 304 ) table 1&2 heat treatment condition 2b as per table-5, coil id 450- 800mm, od 1000-1300mm, coil weight 2.4-10 tonnes., packing instruction: stainless steel ( austenitic & ferritic steel coils etc. ) : the coil shall be protected in reasonably good condition to withstand normal handling hazard during transit with the following provisions as the barest minimum: i ) coil should be wrapped with a layer of water proof paper throughout the whole length. ii ) coil should be wrapped with a layer of biodegradable sheet. iii ) outer & inner of coil should be wrapped with gi sheet. iv ) side of the coil should be covered with card board sheet. v ) after this whole coil should be wrapped with biodegradable plastic sheet of suitable thickness. vi ) the inner edge of the coil should be protected by gi ring , followed by another iron ring. vii ) outer edge of the coil should be wrapped with gi ring. viii ) coil should be securely strapped with minimum 5 steel bands through the eyes of the coil and minimum 3 steel bands on the circumference of the eye. ix ) whole coil should be mounted on wooden blocks for easy lifting / stacking. , austenitic steel coil 1.7x1100mm., as per drawing / specification: rdso spec no.c- k201, grade x5crni1810 ( 304 ) table 1 & 2, heat treatment condition 2b as per table-5, coil id 450-650mm, od 1000-1300mm, coil weight 5-10 tonnes., packing instruction: stainless steel ( austenitic & ferritic steel coils etc. ) : the coil shall be protected in reasonably good condition to withstand normal handling hazard during transit with the following provisions as the barest minimum: i ) coil should be wrapped with a layer of water proof paper throughout the whole length. ii ) coil should be wrapped with a layer of biodegradable sheet. iii ) outer & inner of coil should be wrapped with gi sheet. iv ) side of the coil should be covered with card board sheet. v ) after this whole coil should be wrapped with biodegradable plastic sheet of suitable thickness. vi ) the inner edge of the coil should be protected by gi ring , followed by another iron ring. vii ) outer edge of the coil should be wrapped with gi ring. viii ) coil should be securely strapped with minimum 5 steel bands through the eyes of the coil and minimum 3 steel bands on the circumference of the eye. ix ) whole coil should be mounted on wooden blocks for easy lifting / stacking.