tender for misc. civil works in sabhagar bhawan - 1 demolishing brick work manually by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. in cement mortar. 2 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 3 dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: for thickness of tiles 10 mm to 25 mm. 4 demolishing cement concrete manually by mechanical means including disposal of material within 50 metres lead as per direction of engineer-in-charge. 1:3:6 or richer mix. 5 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1:4 ( 1 cement : 4 coarse sand ) 6 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. 7 half brick masonry in superstructure, above plinth level upto floor vlevelusing bricks of designation 75 cement mortar 1:4 ( 1 cement : 4 coarse sand ) 8 supplying and fixing stone lintels / bed plates of approved quarry rough dressed in cement mortar 1:4 upto 15 cm thick. 9 providing and fixing steel gate, grating, and grills made of angles, tees, square bars, flats or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 10 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm × 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete ( excluding the cost of cement plaster on walls and pillar ) . 11 extra for using size above 200×300mm in glazed tiles and for using 400mm × 400mm mat finished tiles in place of 300mm × 300mm size. 12 providingandfixing75 mm wide decorativeborderindifferentshadesandin allcolouresinglazedtiles laid over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white mixed with pigment of matching shade complete. 13 providing and fixing 1st quality mat finished ceremic tile size 300×300mm confirming to is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete ( including the cost of cement mortar bed 1:4 ) . 14 extra for using size above 200×300mm in glazed tiles and for using 400mm × 400mm mat finished tiles in place of 300mm × 300mm size. 15 p & f 1st quality vitrified porcelain polished tiles on floor, skirting and steps etc. in different sizes ( thickness to be specified by manufacturer ) with water absorption less than 0.08% and conforming to is:15622 of approved make in all colour and shade, laid with 20 mm thick cm 1:4 including grouting the joints with white cement and matching pigment etc complete. size 600 mm × 600 mm. 16 supplying and filling in plinth with blown sand under floors including watering ramming consolidating and dressing complete including cost of sand. 17 random rubble dry stone kharanja under floor. 18 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m-20 grade nominal mix 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size ) . 19 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m-10 grade nominal mix 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size ) . 20 providing and fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is:733 and is:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap at junctions, at top, bottom and sides with required pvc / neoprene felt etc. aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws al. tower bolt & al. handle & al. aldrop etc., all complete as per architectural drawings and the directions of engineer-in-charge. ( glazing and paneling to be paid for separately ) . powder coating aluminum ( minimum thickness of powder coating 50 micron ) 21 providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm × 6.0mm and opening of size 102mm × 99mm to aluminum window / vent with required screws, y and h aluminium section ( as per drawing ) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. powder coating aluminum ( minimum thickness of powder coating 50 micron ) 22 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with pvs / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. ( cost of aluminium snap beading shall be paid in basic item ) with float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg / sqm ) 23 providing and fixing external grade board solid core single leaf flush door shutters isi 2202-67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 30 mm thick. commercial veneer both side 24 extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters ( over all area of door shutter to be measured ) over item no. 8.13. 25 providing and fixing is : 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. 26 providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete. new plastered surface ( three or more coats ) 27 painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including preparation of base with sand papering, primer, putty, etc. complete in all respect including scaffolding and safety provision. new work. 28 painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including preparation of base with sand papering, primer, putty, etc. complete in all respect including scaffolding and safety provision. old work. 29 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding : two or more coats on new work including preparation of base with primer, putty, lippy etc. complete in all respect. 30 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: old work ( one or more coats ) 31 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work. 32 french sprit polishing : two or more coats on new work including a coat of wood filler. 33 providing and fixing stainless steel railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . ( a ) grade 304 34 providing and fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap at junctions, at top, bottom and sides with required pvc / neoprene felt etc. aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws al. tower bolt & al. handle & al. aldrop etc., all complete as per architectural drawings and the directions of engineer- in-charge. ( glazing and paneling to be paid for separately ) . anodised aluminum ( anodised transparent 81 dyed to required shade according to is : 1868. ( minimum anodic coating of grade ac 15, anodizing to be got done from approved anodizer ) 35 providing and fixing 25 mm thick non slippery reflective type designer paving tile with metallic hardening using 2 kg / sq. mtr made out of cement concrete of required grade, sizes of tile upto 300×300 mm manufactured with wet cast vibration system in two layers and laid over base of 20 mm thick cement morter1:4 using neat cement slurry in cluding finishing of joints etc. complete. using m-40 grade cement concrete. 36 providing and fixing stone slabs table rubbed, 15-18 mm thick in walls, steps, pillars, counters, jambs, shelves, sills etc. laid on 12mm ( av. ) thick base of cm 1:3 ( 1 cement : 3 coarse sand ) jointing with white cement mortar 1:2 ( 1white cement : 2 marble dust ) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. makrana adanga. above 3601 cm2 slabs 37 p & f european type white glazed vitreous china 1st quality w.c pan ( is : 2556 mark ) with p or s trap including cutting and making good the wall and floor 38 providing & fixing premium quality white glazed vitreous china sanitary wares ( is:2556 mark ) of approved make as per direction of engineer-in-charge including cutting and making good the wall and floor. wall mounting european type w.c. 39 supply of hydraulic seat cover for european wc of superior quality approved make in white colour 40 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. health facet ( premium heavy quality ) as approved by engineer-in-charge 41 p & f c.p. brass urinal spreader for large urinal of heavy duty of approved make as per direction of engineer-in-charge 42 providing & fixing concealed cistern with floor mounting frame and flush plate of superior quality and approved sample by engineer-in-charge. 43 p & f water closet seat covers with brass hinges complete : solid pvc ( is 2548 marked ) grade-i white for ewc. 44 providing & fixing premium quality bottle trap internal portion 32mm, size 250mm long wall connection pipe & wall flange as per approved by engineer in charge. 45 providing & fixing premium quality wvc urinal with pvc waste pipe, dome couplings, concealed iron brackets or screws etc. complete. flat back ( large ) or half stall size 590×375×390 mm. 46 providing & fixing premium quality wvc wash basin with c.i. brackets duly painted & 32 mm c.p. brass waste coupling of approved make with pvc waste pipe complete. size 550 mm × 400 mm dia for counter top. 47 p & f wvc wash basin ( ist quality is:2556 mark ) of approved make with c.i. brackets duly painted 1 no. 15 mm c.p. pillar cock ( is:8934 mark ) & 32 mm c.p. brass waste coupling of approved make, p.v.c waste pipe with pvc nut 32 mm complete including cutting & making good the wall : size 550 mm × 400 mm 48 p & f low level flushing cistern of 10 litres capacity ( is : 2556 mark ) of approved make with complete fittings c.i. brackets duly painted, brass ball cock with ball ( is: 1703 mark ) complete including cutting and making good the wall : pvc with pvc withpvcbend and superior internal fittings as per is : 7231. 49 p & f c.p. brass urinal flush pipe set complete with flanged brackets of approved make. for 1 urinal 50 p & f looking mirrors with p.v.c. frame of approved make as per direction of engineer-in-charge. round 500mm dia 51 p & f toilet shelf of approved quality / make. acrylic shelf on c.p. brass casted brackets & guard rail of approved make as per direction of ei ofsize 550×125mm 52 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. jet spray ( premium heavy quality ) as approved by engineer-in-charge 53 providing and fixing premium quality towel rack 600mm long 260mm wide with lower hangers cp brass fittings of approved make as per direction of engineer-in-charge 54 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. 600 mm long towel rail 55 p & f grating of approved quality / make: stainless steel sheet size 125mm dia. 56 p & f liquid soap container with brackets complete of approved make: c.p. brass. 57 p & f tooth paste & brush holder of approved quality / make: c.p. brass ( heavy and superior quality ) 58 p & f toilet paper holder with rod of approved quality / make: c.p. brass heavy & superior quality. 59 p & f soap dish or tray of approved quality / make. wvc ( 1st quality, is 2556 marked ) recessed size 150×150 mm. soap dish 380 mm. 60 p & f extension pipe for bib cocks of approved quality / make. c.p. brass of heavy & superior quality 150×15 mm. 61 providing & fixing c.p. flange for 15mm dia taps. 62 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. central hole basin mixer 63 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. bib cock with long thread 15 mm nominal size 64 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. long body bib cock 15 mm nominal size 65 p & f stop cock ( is : 8931 mark ) , superior quality & of approved make : brass 400 gm 15mm nominal bore. 750 gm. 20 mm nominal bore. 66 p & f ball cock ( is:1703 mark ) with rod & p.v.c. ball complete : brass wt. not less than 800 gm, 32mm. 67 p & f inlet connection ( angle valves ) superior quality, of approved make, for wash basin, gyser etc. c.p. inlet connection 15mm brass ( is : 8931 marked ) with 37 cm long pipe and nut. 68 p & f 15 mm dia connection pipe of approved quality / make : pvc pipe withc.p. brass nuts upto length, 600mm 69 p & f full-way valve ( is:778 mark ) or wheel valve of approved make : gun-metal 20 mm nominal bore. 70 p & f full-way valve ( is:778 mark ) or wheel valve of approved make : gun-metal 25 mm nominal bore. 71 p & f pvc storage tank isi marked ( is : 12701 ) indicating the bis license no ) , of approved make with cover, 25mm dia 1m long g.i. over-flow pipe & 25 cm long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres capacity. 72 hoisting charges for each floor : for items 2.26.1 to 2.26.4 73 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. two way bib cock 15 mm nominal size 74 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. revolving type towel ring 75 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer-in-charge. double coot hook. 76 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes ( is 15778 : 2007 code ) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. ( concealed work including cutting chases and making good the walls etc., ) 15 mm nominal size 77 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes ( is 15778 : 2007 code ) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. ( concealed work including cutting chases and making good the walls etc., ) 20 mm nominal size 78 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes ( is 15778 : 2007 code ) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. ( concealed work including cutting chases and making good the walls etc., ) 25 mm nominal size 79 providing and fixing 3-layer pp-r ( polypropylene random coplymer ) pipes sdr 7.4 uv stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all pp-r plain & brass threaded polypropylene random fittings including trenching, refilling and testing of joint complete as per direction of engineer - in charge. ( external works ) pn-16pipe, 32 mm od 80 p&f rigid pvc pipe ( is:4985 mark ) class ii / ( 4 kg. / cm2. ) approved quality / makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia. 81 p&f rigid pvc pipe ( is:4985 mark ) class ii / ( 4 kg / cm2 ) approved quality / make including joining the pipe with solvent cement rubber ring and lubricant. providing & laying c.c. 1:3:6 ( stone aggregate 20mm nominal size ) all around pvc pipe including 7.5 cm thick bed concrete [ width & height =dia of pipe in cm+15cm ] excluding cost of pipe & excavation of trenches etc. pvc pipe 110 mm dia. 82 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : coupler ( socket ) 110 mm dia. 83 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : plain tee 110 mm dia. 84 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : door tee110 mm dia. 85 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : bend 45. 110 mm dia. 86 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : bend 87.5. 110 mm dia. 87 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : door bend ( top side ) .110 mm dia. 88 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : vent cowel. 110 mm dia. 89 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : socket plug. 110 mm dia. 90 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : pipe clip. 110 mm dia. 91 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : p-trap. 110 mm dia. 92 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : gully trap. 110 mm dia. 93 construction of manhole in all type of soil inner size 90 × 60 cm 300 mm thick masonry in cm 1:6, 10 cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in cm 1:6, finished with floating neat cement, 50mm thick m-15 grade c.c. flooring, making channels, 80mm thick stone slab covering with 40mm thick m-15 grade c.c. flooring, cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. depth up to 0.5 m 94 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m, 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m-15 grade c.c. flooring, earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 300×300 mm depth upto 0.5m cement cover with frame. 95 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m, 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m-15 grade c.c. flooring, earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 450×450 mm depth upto 0.5 mcement cover with frame. 96 construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in cm 1:6, 80mm thick stone slab, jointing of slab in cm 1:3, ralthal, kharanja, 40 mm thick m-15 grade c.c flooring, earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: size 300 cm. dia outside & 300 cm. depth. 97 construction of soakage trench inall types of soilwith 300 mm thick dry stone masonry, 80 mm thickstone slab covering, jointing of slab in cm 1:3 ralthal, kharanja, 40 mm thick m-15grade c.c. flooring earthwork etc. complete as per approved drawing including disposalof earth within a lead of 50 mtr.: top width 180cm., bottom width 90cm. & depth 240cm. 98 construction of septic tank in all types of soil with 40 cm thick masonry in cm 1:6, 15 cm thick c.c bed of 1:5:10, m-15 gradec.c floor &rcc slab covering with m15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in cm 1:6 finished with neat floating cement, 4 nos. stone foot rests of approved design , two no. 450 mm dia each ferro cementcover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr. -size 200×100×130 cm. ( for 10 users ) with 115 mm thick rcc ( m-20 ) slab with tor steel reinforcement 8mm ? @15 cm c / c bothways including shuttering complete in all respect.