repairs to joinery and other connected items in md accn and otm accn under age b / r-i of ge brichgunj - 1 taking down chowkats or frames n. exc. 1.5 square metre each with shutters ( without taking off shutter from the frame ) including cutting holes to facilitate the taking down, inserting hold fast while provision and making good disturbed surfaces in cm ( 1:3 ) or pcc ( 1:2:4 ) type b-1 as required, complete all as specified and as directed 2 all as per item no 1 here in before but exc 1.5 n exc 4 square metre each. 3 taking down shutters of any description n.exc 1 square metre each all as directed. 4 taking down shutters of any description exc 1 square metre and n.exc 2square metre each all as directed. 5 supply and fix second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints. 6 supply and fix 35 mm thick 2 nd class hard wood panelled shutters with panels of timber flat on both sides ( feather edges ) or of veneered particle board medium density , wood particle board with commercial face veneers supplied and fitted to chowkats factory made second class hard wood, chemically face veneers etc. 7 supply and fix 35 mm thick 2nd class hard wood glazed / and skeleton shutters open rebated and prepared to receive glass / gauze etc. ( without sash bars ) edges of framing plain chamfered or round fitted with cut and mitred beads for securing glass gauze etc. and fitted to chowkats etc. all as directed by engr-in-charge . 8 cutting holes for inserting hold fasts in pcc block masonry built in cement mortar and making good disturbed portion in pcc 1:2:4 type b1 or in cement mortar 1:3 as required, depth of embedded portion exceeding half brick but not exceeding one brick for full brick walls, complete all as specified and as directed by engineer-in-charge. 9 material and labour for preparing surface of wood and wood based materials and treating ends of posts, backs of chowkats etc area tarred exceeding 0.10 square metre but not exceeding 0.50 square metre each treated with tar or coal tar black paint, complete all as specified and as directed by engineer-in-charge. 10 material and labour for synthetic enamel paint of two coats over a coat of pink primer incl preparation of new wooden surfaces over 10 cm width or girth complete all as specified and as directed. 11 taking down aluminium chowkats or partition frames of any description including glass panes, rubber packing, snap beading, particle board, etc available at site complete all as specified and as directed 12 supply and fix in repairs aluminium snake guard comprising nylon bristle duly secured with aluminium flat section of minimum width 30 mm and length 900 mm fixed to bottom rail of door shutter using aluminium screws complete all as specified and as directed 13 supply and fix solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with ms square tube, supplying & fixing in opening as per specification & drawing. 14 supply and fix factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of ms tubes for top & bottom rails. ms frame shall be covered with heat moulded plain colour pvc `c channel having at pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. 15 material and labour for anodized aluminium sections ( minimum anodisation 15 micros ) for partitions, window and door with frame and shutters fully or partially glazed, side hung type ( two numbers glazed and gauzed ) without sash bars, with panel inserts of sheet glass, gauze including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, the size of aluminium sections shall be all as specified in relevant is code and ssr part-i and completed all as specified and as directed by engineer-in-charge. n ( note: ( i ) supply only panel inserts of glass / gauze will be measured and paid separately as supply only. n ( ii ) weight of aluminium section only shall be accounted for payments purpose. however, until rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as handles, butt hinges, tower bolts and fixing only of panel inserts of glass / particle board / gauze, etc. n ( iii ) weight of aluminium handles, butt hinges & tower bolts shall not be accounted for payment purpose ) 16 supply only 4 mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares not exceeding 0.50 square metre in each pane complete all as specified and as directed. 17 supply only 5.5 mm thick sheet glass and glazing with rubber packing around the glass, in squares exceeding 0.50 square metre in each pane complete all as specified and as directed. 18 supply only 12 mm thick prelaminated particle board exterior grade both side laminated and fixed to aluminium frame. 19 supply and fix in repair 12 mm thick prelaminated particle board exterior grade both side laminated and fixed to aluminium frame. 20 supply only aluminium anodised fly proof mesh 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium straps complete all as directed 21 supply and fix in repairs 18 / 19 mm thick pre- laminated particle board exterior grade pre- laminated on both side with decorative choice lamination fixed with beading as in pelmet box, cupboard shutter etc, complete all as directed by engr-in-charge 22 material and labour in repair 12 mm plywood grade bwp, type bb fixed with beading and nails to timber frame as in partition in kitchen cabinet / cupboard shelves, board etc all as specified and as directed by engr-in-charge. 23 material and labour for hacking out old broken glass ( any thickness, size, quality or description ) from wooden metal / aluminium frames, including oil putty or removing beadings etc, complete all as directed by engr-in-charge 24 supply and fix 4 mm thick sheet glass ordinary quality not exceeding 0.50 square metre in each pane complete all as specified and as directed. 25 supply & fix 5.5 mm thick sheet glass ordinary quality exceeding 0.50 square metre in each pane complete all as specified and as directed. 26 supply & fix 4 mm thick figured glass not exceeding 0.50 square metre in each pane complete all as specified and as directed. 27 supply and fix 4 mm thick figured glass exceeding 0.50 square metre in each pane complete all as specified and as directed. 28 supply and fix butt hinges, of size 100 mm length extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type b-21 complete all as specified and as directed. 29 supply and fix aluminium alloy anodised sliding door bolt with hasp, staple ( bolt type ) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy complete all as specified and as directed. 30 supply and fix aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified and as directed. 31 supply and fix aluminium anodised, barrel tower bolts of extruded section of 100 mm long complete all as specified and as directed. 32 supply and fix 100 mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and as directed. 33 supply and fix 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and as directed. 34 supply and fix in repairs stainless steel 20mm dia best quality decorative type curtain rod complete all as specified and as directed by engineer-in-charge. 35 supply and fix stainless steel curtain brackets with holder for 20mm dia curtain rod decorative type complete all as specified and as directed by engineer-in-charge. 36 supply and fix in repair butt hinges, of size 100 mm length extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type b-21 37 supply and fix in repair aluminium alloy anodised sliding door bolt with hasp, staple ( bolt type ) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy 38 supply and fix in repair aluminium anodised barrel tower bolt of extruded section of size 150mm long 39 supply and fix in repair aluminium anodised, barrel tower bolts of extruded section of 100 mm long. 40 supply and fix in repair 100 mm long extruded aluminium alloy anodised handles fabricated type 41 supply and fix in repair 150 mm long extruded aluminium alloy anodised handles fabricated type 42 supply and fix in repair aluminium wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm complete 43 supply and fix in repair aluminium ( die cast ) body door closer hydraulically regulated designation no. 3 universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kilogram all as specified and as directed 44 material and labour for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed. 45 supply and fix in repair floor door stopper of length of cover plate 140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring 46 dismantling mild steel work of any description not otherwise provided for complete all as specified and as directed by engineer-in-charge. 47 supply and fix for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering. doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing, fe 410-w ( gde-e-250 ) quality-b, etc complete all as specified and directed. 48 supply and fix 1.25mm thick mild steel sheet in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints or welded / riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and as directed. 49 supply and fix for rolled ms work of ms plates, angles, channels etc, fixed independently without connecting plate etc. confirming to fe-290 ( grade e-165 ) complete all as specified and as directed. 50 supply and fix of 1.25mm thick steel rolling shutters, push pull or manual type without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, push pull type rolling shutters made with 1.00mm thick mild steel laths, without ball bearing including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position complete all as specified and as directed. 51 material and labour for two coats synthetic enamel paint over a coat of red oxide primer on newly steel surfaces complete all as specified and as directed. 52 supply and fix in repair 12 mm plywood grade bwp, type bb fixed with beading and screwed to frame of any description as in eaves board etc all as directed by engr-in-charge. 53 supply and fix in repair eco board 600x600x4mm thick decorative type fixed in existing aluminium grid frame work for false ceiling all as specified and as directed. 54 material and labour for false ceiling with aluminium grid work ( size of grid 605x605mm ) with 35x25x1.5mm main tee and 25x25x1.4mm, cross tee and wall angle and suspended with 3.15mm dia, gi wire, hooked to roof with needful adjustment bolts at an interval of 1.20m, centre to centre staggered and board with eco board, decorative type, size 600x600x4mm thick, finished with two coats of oil bound distemper over a coat of primer on exposed surfaces incl dismantling existing ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets / frames of any description, complete all as specified and as directed by engineer-in-charge. 55 dismantling boarding of any description, fixed in any position with nails / screws complete all as specified and as directed. 56 material and labour for providing 15mm thick superior quality chemically pressure treated edged glued finger jointed rubber wood boarding tongued grooved fixed over rubber wood frame work with rubber wood runner of size 50mm x 15mm fixed at 1200mm c / c horizontally by secret nailing with brass screws duly fixed to wall including provision of designed rubber wood beading to top and bottom termination of wood boarding and finished with two coats of melamine polish over a coat of honey / natural colour wood filler putty etc, including preparation and applying sand paper and finishing to a glossy / mat finish complete all as specified and as directed. make :- rubco or equivalent 57 supply and fix aluminium composite panel sheet of 3 to 4 mm thick as in wall cladding & false ceiling, fixed on aluminium frame work with plastic strips ( double sided sticker ) of suitable size of varying thickness of 10mm to 30 mm including aluminium frame work, applying adhesive over aluminium sections for fixing composite panel and fixed with screws. the joints of panels shall be filled with weather proof sealant, the board shall be stuck with a layer of any colour high intensity reflective grade polymer sticker installed using epoxy adhesive complete all as specified and as directed. 58 supply and fix best quality shera planks 8 mm thick, as in claddings of approved colour and coat complete with necessary screws, studs, bolts etc to metal frame complete. ( note : necessary frame work will be measured and paid separately ) 59 material and labour for stainless steel of grade ss-316, mirror polished square, rectangular or circular pipe of different size for structural shed, balusters and railing, railing chain etc, including stainless steel arc welding and bright finishing by polishing with grinding etc, including taking down old ss railing etc complete all as specified and as directed by engineer-in-charge. 60 m&l providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed 61 m&l post construction att along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in aprons of external walls complete all as specified and directed 62 m&l post construction att of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and directed 63 m&l post construction att of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand ) to match the existing floors complete all as specified and directed 64 m&l post construction att at points of contact of wood work by chemical emulsion ( in oil or kerosene-based solution ) at the rate of 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed