supply of furniture items for op wks shelters in 2 mtn div sector , f . o . r : dinjan , chair writing wooden . chair writing of size 535 x 470 x 890 mm shall be provided . chair shall be made out of well seasoned 1st class teak wood free from knots . all wooden exposed surfaces shall be finished with to coats of french polish high gloss finish after preparation of wooden surface . plastic cane seat of size 470 x 470 x 535 with arm rest of size 60 x 25 mm shall be provided . the legs will be fitted with hard pvc shoe . all as per drg no fd 280 sheet 1/1 and technical specification given in shedule-i ( a ) of rfp . , writing table . table of size 1145 x 610 x 760 mm shall be provided . table top shall be 19 mm thick pre-laminated decorated particle board fixed with hollow section frame with screw @ 200 mm c/c . the frame work of table shall be of ms hollow section of size 25 x 25 mm all as per drg . end of legs will be sealed with ms sheet 1 . 6 mm thick with proper welding process to avoid the dust entry . 6 mm thick teak wooden lipping shall be provided on all the exposed edges of mdf duly treated with french polish as specified . all steel surface will have two coats of synthetic enamel paint over a coat of red oxide primer . the legs will be fitted with hard pvc shoe . all as per drg no wt 1/1 and technical specification given in shedule-i ( a ) of rfp . , chair dining . chair dining of size 440 x 430 x 890 mm shall be provided . chair shall be made out of well seasoned 1st class teak wood free from knots . all wooden exposed surfaces shall be finished with two coat of french polish high gloss finish after preparation of wooden surfaces . single piece pvc seat of size 440 x 430 x 405 mm with 4 x 10 mm thick ribbsmoulded shall be provided . the legs will be fitted with pvc shoe hard . all as per drg no fd/map/03 sh 1/1 & technical specification given in schedule-ia of rfp . , table dining . table dining of size 1800 x 900 x 750 mm shall be provided . table top shall be 19 mm thick pre-laminated decorated particle board sheet fixed with hollow section frame with screw @ 200 mm c/c . the frame work of table shall be of ms hollow section of size 25 x 25 mm all as per drg . end of legs will be sealed with ms sheet 1 . 6 mm thick with proper welding process to avoid the dust entry . 6 mm thick teak wood lipping shall be provided on all the exposed edges of mdf duly treated with french polish as specified . all steel surface will have two coats of synthetic enamel paint over a coat of red oxide primer . the legs will be fitted with pvc shoe hard . refer all as per drg no dt 1/1 & technical specification given in schedule-ia of rfp . , stainless steel table . stainless steel table of size 1800 x 750 x 760 mm shall be provided . table top shall be 14 gauge stainless steel sheet on top fixed with 35mm stainless steel square pipe with screw . the frame work of table shall be made of stainless steel tube of size 35 x 35 x 1 . 25 mm thick all as per drg . stainless steel wire mesh shall be fixed at the bottom of the table as per drg . the legs will be fitted with hard rubber shoe . all as per drg no sst 1/1 & technical specification given in schedule-ia of rfp . , almirah steel large . almirah steel large shall as per drawing of size 1300x485x1985mm made up of 20 mm thick ms sheet . four number of shelves shall be provided equally spaced to make five compartments . one chromium plated handle 150 mm long with 3 way locking device shall be provided . in addition one hasp and staple of size 150 mm long shall be provided for alternative locking arrangements . all steel surfaces internally and externally to be painted with 2 coats of synthetic enamel paint over a coat of red oxide . all as per drg no asl 1/1 & tecnical specification given in schedule-ia of rfp . , store rack . consists of four platforms , each made of rigid angle iron frame work to hold 4x2 , 12mm thick plywood . all four rigid platforms to be supported at four corners with angle iron vertical columns as per spacing mentioned in drawing no sr-1/1 with suitable nut bolts . angle iron size 40mm x 40mm x 5mm to be used . bracing with ms flat of size 40mm x 5mm to be provided at the rear . all as per drawing no sr-1/1 and technical specification given in part-ii of rfp .