tender for supply of electrical and electronics engineering department lab equipments are required as per new syllabus , upgradation of labarotaries ece department , 8051 micro controller kit • operating voltage: +5 v dc. • flash memory: 4 kb (at89c51) / 8 kb (at89s52). • ram: 128 bytes internal ram. • 16 × 2 alphanumeric lcd display. • push buttons / tactile switches. • dip switches for digital input. • inbuilt adc interface: ldr, potentiometer. • inbuilt dac interface. • inbuilt stepper motor driver with stepper motor. • inbuilt dc motor driver with dc motor. • 1 × 4 led array, 1 × 4 keypad, 1 × relay. • 1 × buzzer, 16 × 2 lcd display, 1 × pwm driver. • 1 × hardware interrupt key, inbuilt rtc. • inbuilt eeprom and uart module. • 4 × 7-segment display. • supports both assembly and c language programming. • pc interfaceable. , single phase induction motor 1 hp, 230 v ac, 1500 rpm with loading arrangement - 1 no. voltmeter: (0-300) v ac, 96 × 96 mm with input terminals - 1 no. ammeter: (0-10) a ac, 96 × 96 mm with input terminals - 1 no. wattmeter: 2 kw, 96 × 96 mm with input terminals - 1 no. power factor meter: 96 × 96 mm with input terminals - 1 no. auto transformer: 0-300 v, 1φ variac - 1 no. mcb: 2-pole, 40 a / 230 v ac - 1 no. digital rpm indicator with proximity sensor - 1 no. aluminium brake drum: 230 mm diameter - 1 no. spring balance: (0-25) kg - 02 nos. circuit diagram printed on front panel with instruments and connecting terminals. motor and loading arrangement mounted on rigid channel frame with anti-vibration mounting pads, m12 × 1.5 bolt & nut, 85 mm dia - 4 nos. mild steel powder-coated electrical panel table setup. , auto transformer input: 230-240 v ac, 50 hz. output: variable (0-270) v ac. rating: 1 kva. insulation class: class f / class h. construction: copper winding with carbon brush arrangement. mounting: bench-top / panel type. protection: suitable fuse / overload protection. , dth trainer kit power supply: • 200 v to 240 v ac, 50 hz. dish antenna: • 1.5 ft aluminium steerable dish antenna. lnb (low noise block down converter): • input frequency: ku-band. • output frequency: 950 mhz to 1450 mhz. • conversion gain: 65 db. • noise temperature: 35 k (max). set-top box receiver in trainer form: • if frequency: 70 mhz. • video bandwidth: 50 hz to 5 mhz. • video output level: 1 vpp at 75 ω load. • video polarity: normal/inverted, switch selectable. • audio subcarrier frequency: tunable from 5.0 mhz to 8.0 mhz. • remote control provided. • hdmi cable: 10 m. controls: • channel selection. • volume control. fault simulation: • five built-in simulated faults for troubleshooting experiments. • if signal disconnected. • video output fault. • audio mute fault. • tuner misalignment. • rf output interruption. pcb size: • 15 × 12 with multicolour section-wise block diagram. standard accessories: • 1.5 ft dish antenna. • lnb. • trainer pcb. • dish connecting wire.• audio-video cable. • user manual. • acrylic cover.• hardware materials for assembly of dish antenna. additional features: • dth subscription connection with doordarshanfree channels. , sim reader trainer kit power supply: • operates on 230 v ac ±10%, 50 hz mains supply. • built-in regulated smps power supply. • operating dc supply: 5 v / 12 v with overload and short-circuit protection. sim card interface: • supports gsm sim cards compatible with 2g / 3g / 4g / 5g networks. • sim card read/write interface. • supports sim card initialization, authentication, and communication functions. • compatible with standard 6-pin / 8-pin sim card sockets. communication interface: • usb 2.0 interface for pc communication. • rs-232 serial communication interface. • uart communication facility for embedded system interfacing. sim operating parameters: • selectable sim clock frequencies: • 3.579 mhz • 7.159 mhz • 14.318 mhz • sim supply voltage selection facility. • sim reset and activation control. supported protocols and standards: • gsm etsi 07.07 and etsi 07.05 at command support. • iso/iec 7816 smart card communication support. • sim communication command monitoring facility. hardware features: • on-board sim card socket. • led indication for: • power status • sim detection • reset activity • data transmission/reception • built -in keypad for standalone operation. • lcd display module (128 × 64) for menu and status display. • on -board microcontroller -based control section. software support: • at command execution and monitoring software. • sim manager utility software.• data logging and communication terminal utility. • pc -based gui software for sim data communication experiments. trainer features: • fault simulation facility for troubleshooting experiments. • simulation of faults such as: • sim not detected • clock failure • vcc failure • reset failure • multiple on -board test points for signal observation. • test points for: • sim_rst • sim_clk • sim_io • vcc • uart tx/rx • suitable for cro/dso signal monitoring. • glass epoxy pcb with educational block diagram layout. • compact tabletop enclosed cabinet design. construction: • front panel with printed block diagram.• banana test points and patching facility. standard accessories: • gsm sim trainer unit. • usb communication cable. • rs-232 communication cable. • power cord. • user manual. • utility software cd / downloadable software package. , fpga trainer kit • must use industry-standard mid-range fpga device • usb-jtag programmable, compatible with vivado ise (webpack). • power supply: 5 v dc through usb or external adapter. • on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb-uart bridge, usb cable. •user manual.