bids are invited for 1 earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer-in-charge. all kinds of soil 20.00 cum 2 filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m 10.00 cum 3 supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 10.00 cum 4 surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto 1.5m: all kinds of soil 100.00 sqm 5 cleaning jungle including uprooting of rank vegetation, grass, brush wood, trees and sapling of girth upto 30cm. measured at a height of 1 m above ground level and removal of rubbish upto a distance of 2km out side the periphery of the area cleared by your own vehicle. 18000.00 sqm 6 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-iii) : 4 graded stone aggregate 20 mm nominal size) 40.00 cum 7 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level .grade:-1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) 10.00 cum 8 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work above plinth level .grade:-1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) 10 cum 9 providing and laying for fixing steel reinforcement for reinforced cement concrete work including transporting , decoiling, straightening, cutting, derusting bending, placing in position at all height and binding with binding wire etc. complete as per drawing, specification and instruction of the engineer-in-charge. 1200 kg 10 centering and shuttering including strutting, propping etc. and removal of form for : foundations, footings, bases of columns, etc. for mass concrete 150.00 sqm 11 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 150.00 sqm 12 providing and laying for 40mm thick cement concrete in flooring, in ratio 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate) finished with a floating coats of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete including cost of all materials 200.00 sqm 13 grading of roof for water proofing treatment with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12mm nominal size) mix with sika top seal and sikadur 32 in appropriate proportion. 10.00 cum 14 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:6 (1 cement : 6 coarse sand) 20.00 cum 15 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) 30.00 cum 16 half brick masonry with common burnt clay f .p .s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1:4 (1 cement :4 coarse sand) 100.00 sqm 17 12 mm cement plaster of mix : 1: 6 (1 cement : 6 coarse sand 200.00 sqm 18 providing neat cement punning about 1.5mm thick in wall, dado, window sills, plinth etc. and like at any level to anywhere as directed and specified by the engineer-in-charge. 200.00 sqm 19 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.m including cutting the patches in proper shape, raking out joints and preparing and plastering( 1 :4 ) the surface of the walls complete shade including cost of all materials, labours, scaffolding, tools and tackles , disposal of rubbish to the dump yard with in 50 m lead. 100.00 sqm 20 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 400.00 sqm 21 removing dry/oil bound distemper by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 200.00 sqm 22 removing white or color wash snowcem/distemper by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 200.00 sqm 23 white washing with lime to give an even shade : new work (three or more coats). 2000.00 sqm 24 applying priming coat: with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 500.00 sqm 25 applying priming coat: with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works 500.00 sqm 26 applying priming coats with primer of approved brand and manufacture, having low voc (volatile organic compound ) content. with water thinnable cement primer on wall surface having voc content less than 50 grams/litre 500.00 sqm 27 finishing walls with waterproofing cement paint of approved brand and manufacture and of required shade to give an even shade.new work (three or more coats) 500.00 sqm 28 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work (two or more coats) over and including water thinnable priming coat with cement primer 200.00 sqm 29 finishing walls with acrylic smooth exterior paint of required shade : new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 200.00 sqm 30 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. preferable make dulux/burger/asian paints or as per direction of eic 500.00 sqm 31 demolishing of cement conc. including disposal of material within 50m lead.1:3:6 or richer mix 10.00 cum 32 dismantling of old brick work including stacking of serviceable material and disposal of unserviceable material within 50m lead.in cement mortar. 10.00 cum 33 dismantling of old plaster or skirting raking out joints and cleaning the surface of plaster including disposal of rubbish to the dumping yard with 50 mtr. lead. 100.00 sqm 34 providing and laying for fixing and sizing of any sizes of cgi/colour corrugated sheets of 0.63mm thick with ridges and wind tie on roof at any height including scaffolding and etc. all complete as per instruction of engg.-in-charge. 90.00 sqm 35 providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per is: 14871) roofing up to any pitch and fixing with polymer coated j, or l hooks, bolts and nuts 8 mm dia. g.i. plain and bitumen washers or with self drilling fastener and epdm washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required. 90.00 sqm 36 providing and fixing structural steel work reveted,bolted or welded in built up sections, trusses and framed work ,including cutting hoisting, fixing in position and applying a priming coat of approved steel primer. 1000.00 kg 37 providing and fixing anodized aluminum tower bolt (heavy type) including necessary screws etc. complete. 150 x 10mm 40.00 each 38 providing and fixing is : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 125x64x1.90 mm 100.00 each 39 providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type) 40.00 each 40 providing and fixing anodized aluminum tower bolt including necessary screws etc. complete.250 x 10mm 50.00 each 41 providing and fixing anodized aluminum door handle including necessary screws etc. complete.a) 125mm 40.00 each 42 providing and fixing anodized aluminum hanging floor door stopper (twin robber) with necessary screw etc. complete. 40.00 each 43 providing and fixing aluminum. (heavy type) sliding door bolts with nuts and screws etc. complete.a) 300 x 16mm 20.00 each 44 providing and fixing bright finished brass casement window fasteners of minimum weight 200 grams to side hung steel windows with necessary welding and machine screws etc. complete. 50.00 each 45 providing and fixing bright finished brass peg stays 300mm long of minimum weight 330 grams. to side hung steel windows with necessary welding and machine screws etc. complete. 40.00 each 46 providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 50.00 each 47 providing and fixing chromium plated brass night latch of approved quality including necessary screws etc. complete. 20.00 each 48 providing and fixing bright finished brass 100 mm mortice latch and lock, isi marked, with six levers and a pair of anodised (anodic coating not less than grade ac 10 as per is : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. 20.00 each 49 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including isi marked stainless steel butt hinges with necessary screws 80.00 sqm 50 providing and fixing of glass panes, with putty and nails wherever necessary: glass panes 4mm thick. 120.00 sqm 51 providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic molded frame of approved make and shade with 6 mm thick hard board backing : rectangular shape 453x357 mm. 20.00 each 52 rectangular shape 1500x450 mm 8.00 each 53 providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40 mm long screws, rawl, plugs etc., complete. 10.00 each 54 providing and fixing factory made panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture. m.s. frame covered with 5 mm thick heat moulded pvc c channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide pvc sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide pvc sheet out of which 75 mm shall beflat and 20 mm shall be tapered on both sides to form lock rail. top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross pvc sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side pvc sheet to be fitted in the m.s. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide pvc sheet beading on inner side, and joined together with solvent cement adhesive. an additional 5 mm thick pvc strip of 20 mm width is to be stuck on the interior side of the c channel using pvc solvent adhesive etc. complete as per direction of engineer-in-charge, manufacturers specification & drawing. 30 mm thick plain pvc door shutters 30.00 sqm 55 providing and fixing g.i. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of engineer-in-charge. made of g.i. wire of dia 4 mm 200 sqm 56 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge. 15 mm nominal outer dia pipes 90.00 meter 57 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge. 25 mm nominal outer dia pipes 60.00 meter 58 providing and fixing g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc. 15 mm dia nominal bore 90.00 meter 59 providing and fixing g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc. 25 mm dia nominal bore 60.00 meter 60 providing and fixing g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc. 50 mm dia nominal bore 60.00 meter 61 providing and fixing gun metal non- return valve of approved quality (screwed end) :25mm nominal bore a)horizontal 15 each 62 providing and fixing gun metal gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore 15.00 each 63 providing and fixing gun metal gate valve with c.i. wheel of approved quality (screwed end) : 50 mm nominal bore 12.00 each 64 providing and fixing heavy duty c.p brass bib cock of 15mm nominal bore as per approved sample (brand:-jaquar). 24.00 each 65 providing and fixing heavy duty c.p brass stop cock (concealed) of 15mm nominal bore as per approved sample. (brand:-jaquar/cera/hindware). 12.00 each 66 providing and fixing c.p. brass shower rose with 15 or 20 mm inlet : 100 mm diameter (brand:- jaquar/cera/hindware). 6.00 each 67 providing and fixing ptmt bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms 30.00 each 68 providing and fixing ptmt pillar cock of approved quality and colour. 15 mm nominal bore, 107 mm long, weighing not less than 110 gms 10.00 each 69 providing and fixing in position pedestal european type water closet white glazed vitreous chinaware with seat and lid (white) hind ware make or approved brand and quality, 10 litres capacity low level white pvc flushing cistern manually controlled device ( handle lever ) and c.p. flush bend with fitting and brackets, conforming to is : 7231 including assembling all the parts in position and satisfactory testing, 32mm diameter pvc flush pipe with fittings. (the rate quoted shall be satisfactory operation and leak proof joints) . (brand: -jaquar/cera/hindware). 4.00 each 70 providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin with all fittings of 430x260x350 mm or 340x410x265 mm sizes respectively. (brand: -jaquar/cera/hindware). 4.00 each 71 providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white p.v.c.automatic flushing cistern, with fittings, standard size g.i. / pvcflush pipe for back and front flush with standard spreader pipes withfittings, g.i clamps and c.p. brass coupling complete, includingpainting of fittings and cutting and making good the walls and floorsetc. wherever required :single squatting plate with 5 litre p.v.c. automatic flushing cistern (brand: - jaquar/cera/hindware). 4.00 each 72 providing and fixing white vitreous china wash basin with c.i./ m.s. brackets, 15mm c.p.brass pillar tap (single) 32mm c.p. brass waste of standard pattern, including pvc waste pipe and pvc connector pipe including painting of fitting and brackets , cutting and making good the walls wherever required.a)wash basin size: 550 x 400mm. (brand: -jaquar/cera/hindware). 4.00 each 73 providing & fixing white vitreous china water closet squatting pan (indian type) along with s or p trap including dismantling of old wc seat and s or p trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer -in charge. orissa pattern w.c pan of size 580x440 mm (brand: -jaquar/cera/hindware). 4.00 each 74 providing and fixing low level 10 litres capacity white p.v.c. flushing cistern with manually controlled device conformed to is : 7231 with all fittings and fixtures complete (brand: - jaquar/cera/hindware). 75 providing and fixing white solid plastic seat with lid for e.w.c. pan complete. (brand:-jaquar/cera/hindware). 4.00 each 76 providing and fixing 32 mm dia. p.v.c. flexible waste pipes for sinks and wash basins. 4.00 each 77 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion,(i) single socketed pipes.110 mm diameter 30 meter 78 providing and placing on terrace polyethylene water storage tank of 1000 ltr, isi: 12701 with cover and suitable locking arrangement and making necessary holes for inlet and outlets and overflow pipe but without fittings and base supports for tank. 5000.00 litre 79 providing plant budded rose (h.t. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm earthen pot. 200.00 each 80 supply of good quality earthen pot ( gamla) at site earthen pot 10 inch size 300.00 each 81 earthen pot 12 inch size 200.00 each 82 supply of fertilizers, pesticides & fungicides at site: d a p 100.00 kg 83 urea (neem coated) 100.00 kg 84 supplying and stacking of seasonal seedling/cutting at site of work well developed and healthy free from disease plants as per direction of the officerin-charge. marigold inca hybrid 400.00 each 85 portulaca hybrid 400.00 each 86 vinca hybrid 400.00 each 87 dahlia double 200.00 each 88 calendula double 200.00 each 89 chrysanthemum double 200.00 each 90 pansy hybrid 200.00 each 91 petunia hybrid 200.00 each 92 aster dwarf 200.00 each 93 kochia 200.00 each 94 sunflower dwarf 200.00 each 95 lifting, collecting, cleaning and disposal of slurry/mud/dry sand from catch pit drain sumps below conveyor belt , sump behind oil room both side and top of road surface from mines gate to rear gate and including removal of spillage over the road from paddock to rear gate and shifting the same within a radial distance of 2 k.m. by their own transport and dumping the same in specified area as directed by engineer-incharge. total quantity : 41384