tender for provision of street light and other allied work in various location in ward no. 201 under shahdra south zone - supply and fixing of 32mm dia x 1 meter long g.i. pipe (medium class) bracket for mounting of fluorescent/hpmv/hpsv street light fitting on pole including bending the pipe to the required shape , 2 nos 25mm x 6mm flat iron clamps with nuts, bolts and washer , painting the flat iron with primer and finish paint etc. as reqd. 2 supply of xlpe insulated pvc sheathed al. conductor un-armoured cable 1.1kv grade conforming to is-7098 of following size:-2c*4 sqmm 3 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size in the existing masonry open duct as required.upto 35 sq. mm 4 supplying and erection of galvanised d iron clamps complete with shackle insulator (75 mm x 90 mm),g. i. bolts, nuts and washers, coach screws etc.as required. 5 supplying and drawing following sizes of frls pvc insulated copper conductor, single core cable in the existing surface / recessed steel/ pvc conduit as required.3 x 1.5 sq.mm 6 led batten light (system lumen efficacy >135 lm/watt)supplying, installation, testing & commissioning of led surface mounted batten light of following body material and construction as per is : 10322 with driver (replaceable) as per the requirement with driver efficiency >85% ,operating voltage ac 140-270 volt, freq 50/60 hz, operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% , p. f.≥0.95, ip20, cri >80 , flicker free (flicker should be below 5 %), life time (led,driver & electrical circuitry) of minimum 50000 burning hours with , 70% of initial lumen maintained till life ends, cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin), sdcm (standard deviation color matching)<3, maximum power consumption should not more than the specified rating and fixture shall be of relevant bis standard and trade mark certificate (t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. complete in all respect i/c connections with 1.5 sq mm frls, pvc insulated copper conductor single core cable and earthing etc. as required with minimum 5 year oem warranty. system lumen efficacy >135 lm/watt output . lm79 & lm80 test report from nabl lab for all testing required for led fixtures as per bis shall be submitted. shape size and cct shall be as approved by engineerin-charge as per requirement. (thermal management: heat sink of aluminum housing such that led junction temperature shall not rise above 90°c). ( 36 watt) 7 led flood light, powder coated pressure die cast aluminum(system lumen efficacy >135 lm/watt)supplying, installation, testing & commissioning of flood light,powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with driver efficiency >85%, input voltage: input voltage: 140-270 volt ac, freq 50/60 hz, operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 kv l,n,e as per iec 61000-4-5, driver efficiency >85%,thd < 10% as per iec 61000-3-2 , p.f.≥0.95, ip-66,ik-10, cri >80 , under voltage and over voltage protection, emi-emc as per cispr-15, lenses for beam angle 30 deg- 120deg as per the application and the project requirement deg., suitable tilt able fitting, life time (led,driver & electrical circuitry) of minimum 50000 burning hours with 70% of initial lumen maintained till life ends as per lm80 extrapolation ies tm-21-11 report , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , sdcm(standard deviation color matching) <5, maximum power consumption should not more than the specified rating and fixture shall be of relevant bis standard complete in all respect i/c connections with 1.5 sq mm frls, pvc insulated copper conductor single core cable and earthing etc. as required with minimum 5 year oem warranty. system lumen efficacy >135 lm/watt output . lm79 & lm80 test report from nabl lab for all testing required for led fixtures as per bis shall be submitted. shape size and cct shall be as approved by engineer-in-charge as per requirement. (thermal management: heat sink of aluminum housing such that led junction temperature shall not rise above 90°c). 100 watt 8 led street light fixture, powder coated pressure die castaluminum body (system lumen efficacy >135 lm/watt)supplying, installation, testing & commissioning of street light ledfixture, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with driver efficiency >85%, input voltage: 140-270 volt ac, freq 50/60 hz, operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 kv l,n,e as per iec 61000-4- 5, driver efficiency >85%,thd < 10% as per iec 61000-3-2 , p. f.≥0.95, ip-66,ik-10, cri >80 , under voltage and over voltage protection,emiemc as per cispr-15, lenses for beam angle as per iesna type i/ii/iii as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (led,driver & electrical circuitry) of minimum 50000 burning hours with 70% of initial lumen maintained till life ends as per lm80 extrapolation ies tm-21-11 report , cct 3000°k /4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , sdcm(standard deviation color matching) <5, maximum power consumption should not more than the specified rating and fixture shall be of relevant bis standard complete in all respect i/c connections with 1.5 sq mm frls, pvcinsulated copper conductor single core cable and earthing etc. as required with minimum 5 year oem warranty. system lumen efficacy >135 lm/watt output . lm79 & lm80 test report from nabl lab for all testing required for led fixtures as per bis shall be submitted. shape size and cct shall be as approved by engineer-in-charge as per requirement. (thermal management: heat sink of aluminum housing such that led junction temperature shall not rise above 90°c). (50 watt) 9 earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required. 10 providing and laying earth connection from earth electrode with 6 swg dia g.i. wire in 15 mm dia g.i. pipe from earth electrode including connection with g.i. thimble excavation and re-filling as required.