tender for improvement of qm store and dhobi shop at bsf campus panisagar under shq bsf panisagar; 1 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 2 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone - iii) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 3 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundations and plinth in :cement mortar 1:4(1 cement :4 coarse sand) 4 providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including black enamelled isi marked m.s butt hinges with necessary screws.:kiln seasoned and chemically treated hollock wood: 30 mm thick 5 providing and fixing isi marked flush door shutters conforming to is: 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 30 mm thick including isi marked stainless steel butt hinges with necessary screws. 6 providing and fixing wire gauge shutters using galvanized m.s. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: with isi marked m.s. pressed butt hinges bright finished of required size :kiln seasoned and chemically treated hollock wood. 30 mm thick shutters. 7 fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4 mm wide aperture with matching wood beading 8 providing and fixing aluminium sliding door bolts isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm 9 providing and fixing aluminium tower bolts isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to:100x10 mm 10 providing and fixing aluminium handles isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 100 mm 11 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete. with 4.0 mm thick glass panes. 12 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a including jointing with seal ring conforming to is : 5382 leaving 10 mm gap for thermal expansion.(i) single socketed pipes :110 mm diameter 13 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 14 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old work. 15 distempering with 1st quality acrylic distemper (ready made) having voc content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete. as per manufacturer’s specification.. one or more coats on old work. 16 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 17 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 18 cement plaster 1:3(1 cement: 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster 19 finishing walls with acrylic smooth exterior paint of required shade :old work (one or more coat applied @ 0.90 ltr/10 sqm). 20 taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :of area 3 sq. metres and below 21 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead 22 providing and placing on terrace (at all floor levels) polyethylene water storagetank,is : 12701marked,withcoverandsuitablelocking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 23 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge. external work 25 mm nominal dia pipes