Supply Of Tools, Equipments And Machines For Govt Itis Of Gwalior Zone - 1 Air Blow Gun With Standard Accessories :- Plastic Blow Gunthe Body Is Moulded From A Special Acetalic Resin To Resist Damage, Staining And Contamination With A 100% Brass Inner Valve. The Blow Gun Adjusts The Airflow Gradually For Delicate Working. Suitable For Use With Both Air And Water. Recommended Maximum Working Pressure Of 10 Bar ( 150Psi ) . 2 Air Compressor Suitable For Air Plasma Cutting System. 3 Ammeter 300A / 60A Dc With External Shunt 4 Angle Grinder Ag4 5 Arbor Press Hand Operated 2 Ton Capacity, Hand Operated 6 Arc Welding Table ( All Metal Top ) 122 Cm X 12 Cm X 60 Cm With Positioner.With Portable Screen , Welding Booth 7 Auto Electrical Test Bench1. Motor 2 Hp Three Phase 1500Rpm 2. Digital Dc Voltmeter Of 3.5 Digital Display With Minimum Readable Upto 0.1 Volt 3. Digital Dc Ammeter For Load Of 3.5 Digit Display With Minimum Readable Upto 1 Amp. 4. Digital Rpm Indicator 0-5000 Rpm. 5. Speed Sensor For Sensing Starter Speed 6. Alternator Loading Through Wire Wound Resistors Of 0-50 Amps Capacity 5. Alternator Loading Through 4Nos Rotary Switches. 6. Two Directional Rugged Mounting Arrangement To Suit Various Range Of Alternators. 7 Provision For Two Speed Check With Two Set Of Pulley And Belts 8 Starter Free Spin Testing Up To 100 Amps Capacity. 9 110 V Series Lamp Test Facility Also Available. 8 Automotive Exhaust 5 Gas Analyzer ( Petrol & Diesel ) Or Diesel Smoke Meter :- A ) 4 Gas Analyser Arai Approved Measures Co, Hc, Co2, O2, Lambda Rpm, Oil Temperature B ) Diesel Smoke Meter Without System Arai Approved, Black Box Version ( Without Display ) Smoke Density In K / M & % Steady State & Free Acceleration Tests Engine Rpm & Oil Temperature Main Spindle-: Spindle Motor Power 5.5 / 7.5Kw Spindle Bore ( Mm ) 150Spindle Nose A2-5Max. Bar Capacity ( Mm ) 38 Speed Range 50-4500Rpm 9 Car Jet Washer With Standard Accessories Max.Pressure- 130 Bar , Max. Folw Rate-370 L / H , Motor Power -1700W , Max. Flow Temperature-40°C, Weight Without Accessories-6.53Kg, Hose Length / Material - 6M / Pvc , Power Cable Length / Material -5 M / Pvc .Specification As: Max.Pressure- 130 Bar , Max. Folw Rate-370 L / H , Motor Power -1700W , Max. Flow Temperature-40°C, Weight Without Accessories-6.53Kg, Hose Length / Material - 6M / Pvc , Power Cable Length / Material -5 M / Pvc . 10 D.C .Arc Welding Rectifiers Set With All Accessories ( 400A, Ocv 60- 1 00V, 60% Duty Cycle ) Arc Welding Rectifier With Accessories General : 1 ) Thyristorised Power Source With Remote Control For Current Control- 10M. ( 2 ) F- Insulation With Suitable Buffering Material For Thermal Resistance. 3 ) Forced Air Coolin ( 4 ) Protection Class - Ip23. 5 ) Light Weight And Compact Input: 1 ) Supply Voltage - 415V, 3Phase 50Hz Ac 2 ) Characteristics - Constant Currrent 3 ) Maximum Input Power ( A ) 60% Duty Cycle - 23.5Kva ( B ) Input Current At 100% Duty Cycle - 32.5A Output: 1 ) Current Range - 10- 400A ( 2 ) Maximum Current A ) 60% Duty Cycle - 400A, Power Factor - 0.89 B ) 100 % Duty Cicle 310A Power Factor - 0.69 3 ) Open Circuit Voltage - 100V Accessories 11 Pedestal Grinding Machine D.E. With 200Mm Diameter Wheels Rough And Smooth With Twist Drill Grinding Attachment. Direct Driven With Inbuilt Motor Mounted On C.I. Pedestal Stand Hp 1.0 Kw 0.75 Ph 3 Hz 50 Amp 1.6 Volt 415 Rpm 2800 Complete With Grinding Wheel Size: 200 X 25Mm X 19.05 Mm ( Original Bore 31.75 Mm ) , Fitted With Eye Shield, Starter, Wheel Guard, And Standard Tool Rest Plate & Drill Grinding Attachment ( Upto 19 Mm ) Wheel Centre Dist. : 460Mm Centre Height : 940Mmd.E. Pedestal Grinding Machine With 200Mm Diameter Wheels Rough And Smooth With Twist Drill Grinding Attachment.With Water Tank And Switch Roatary Used Carbied Tipped Tool 12 Grinding Machine ( General Purpose ) D.E. Pedestal With 300 Mm Dia Wheels Rough And Smooth Pedestal Grinder Direct Driven With Inbuilt Motor Mounted On C.I. Pedestal Stand Hp 2.00 Kw 1.5 Ph 3 Hz 50 Amp 3.5 Volt 415 Rpm 1400 Complete With Grinding Wheel Size :300 X 50 X 31.75 Mm ( Original Bore 50.8 Mm, ) ( One Coarse & One Medium ) Fitted With Eye Shield, Siemens Starter, Wheel Guard, & Std Tool Rest Plate Wheel Centre Dist. : 615Mm Centre Height : 940Mm 13 Diesel Engine – Crdi - 4 Stroke For Dismantling And Assembling With Swivelling Stand -The Device Is Designed Based On Latest Technology Diesel Engines With Common Rail Direct Fuel Injection System. The Trainer Helps To Simulate Engine Startup, Speedup, Slowdown And Other Actions So As To Illustrate The Structure And Working Principle Of Crdi Engines. Features 1. Real And Operating Crdi Diesel Engine, Illustrating The Structure And Working Process. 2. Coloured Circuit Diagram On The Training Module Printed On To 6Mm Organic Glass Base.. 3. Detection Terminals For Operator To Detect Various Sensors, Actuators, Electrical Signals For Engine Control Unit, Such As Resistive, Voltage, Current , Frequency And Wave Form Signals Are Provided On To The Printed Circuit Diagaram. 4. Automobile Meters Are Fitted On To The Training Module Along With The Printed Circuit Diagram, To Demonstrate Engine Speed, Temperature, Fuel Pressure, Charging Light Etc., 5. The Training Module Is Fitted With Diagnostic Socket ( Dlc ) For Universal Automobile Decoder ( Scan Tool ) To Read Fault Codes, Clear Fault Codes And Read Data Stream. 6. Fault Setting Switch Bank Will Be Provided To Induce Faults In The Training Module To Demonstrate The Fault And To Diagnose Faults. 7. Good Working Condition Engine Will Be Provided With Fuel Tank And Battery. Throttle Control Is Provided On The Module To Accelerate. 8. The Training Module Is Fabricated Using Steel Pipe Frame With Spray Painted For Good Looks And The Entire Setup Is Provided With Caster Wheels With Brakes For Easy Movement Of The Same. 14 Diesel Engine ( Running Condition ) Stationary Type The Four Stroke Diesel Engine Setup To Be Prepared By Using Good Working Condition Single Cylinder Diesel Engine With All The Fittings Of The Engine Along With Air Filter, Fuel Tank , Electrical Wiring Etc., All Mounted On To A Sturdy Iron Frame. 15 Diesel Generator Set With Change Over Switch, Over Current Breaker And Water Cooled With Armature, Star-Delta Connections Ac 3 Phase, 5 Kva, 240 Voltac 3 Phase, 5 Kva, 240 Volt 16 Different Type Of Engine Bearing Model 17 Different Type Of Piston Model This Model Should Be Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information And The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 18 Drilling Machine Bench Sensitive 0-12 Mm Cap Motorised With Chuck And Key. 1.1 Electrical Electric Motor 0.50 Hp 3 Ph Motor 1440 Rpm With R & F Switch & V-Belt. 1.2 13Mm Drill Chuck 1.3 Machine Vice 100Mm [ S G Material ] Extra Accessories: . Isi Make Electric Motor, Switch And V Belt. . Drill Vice . Drill Chuck Drill Bit Set 3 Mm To 12 Mm Set Of 10 Pcs. 19 Drilling Machine Pillar Sensitive 0-20 Mm Cap With Swivel Table Motorised With Chuck & Key. 8 Speed, 4’ Pillar Height, Without Electrical. Extra Accessories : 1.1 Electrical Motor 1 Hp 3 Ph 1440 Rpm With R & F Switch & V-Belt 1.2 13Mm Drill Chuck Mt-2 Arbor & Sleeve Mt-2 / 3 1.3 Machine Vice 100Mm [ S G Material } Drilling Machine Pillar Sensitive 0-20 Mm Cap With Swivel Table Motorised With Chuck & Key. Precision Heavy Duty Pillar Drill Machine, Cap: 20 Mm, Spindle Traveling – 125 Mm, With Standard Accessories Optional: ® Drill Vice ® Drill Chuck, Arbor ® Isi Electric Motor, Switch And V Belt 20 Dual Magnetization Yoke : Ac / Hwdc, 230 Vac, 50Hz Along With Accessories;- A ) Copper Bulb - 1 No B ) Pipe Gauge - 1 No C ) Manual - 1 No D ) Calibration Certificate E ) Carrying Bag F ) Test Bar 21 Oven, Electrode Drying 0 To 350°C, 10 Kg Capacitycap.Input Voltage:- 230V Ac Current Amp:- 7.5 Phase:- 1 Phase Frequancy:- 50Hz Watts:- 1.75 Kw Output Temp:- 50C To 205C Capacity: 10 Kg Or 450Mm Electrod Working Space:- 440X450x490mm ( Hwd ) Temp Control:- Thermostate 22 Fly Press Ball Press No.4 Single Body 23 Fuel Feed Pump For Diesel This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information, And Working Of The Same, The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 24 Fuel Injection Pump ( Diesel ) Inline This Model Should Be Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information And The Model Should Be Suitably Painted And Mounted On A Navopan Wooden Base. 25 Fuel Injection Pump Dismantling Tool Kit / Universal Vice 26 Fuel Injection Pump Distributor Fuel Rotary Pump ( Dpc ) Pumps Along With Special Tools And Accessories . This Model Should Be Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information And The Model Should Be Suitably Painted And Mounted On A Navopan Wooden Base 27 Fuel Injection Pump Ve Pump Along With Special Tools And Accessories. This Model Should Be Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information And The Model Should Be Suitably Painted And Mounted On A Navopan Wooden Base 28 Gas Welding Table 1220Mm X760mm With Positioner 29 Grinding Machine ( General Purpose ) D.E. Pedestal With 300 Mm Dia Wheels Rough And Smooth 30 Hand Press Brake Capacity ( 0.8Mm ) 31 Hydraulic Jack Hi-Lift Type 5 Ton Capacity 32 Injector – Multi Hole Type This Model Is Made Out Of Original Used Part, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information, The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 33 Injector – Pintle Type This Model Is Made Out Of Original Used Part, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information, The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 34 Injector Cleaning Unit Injector Cleaning Kit With Brush And Pin 35 Injector Testing Set ( Hand Tester ) 36 Liquid Penetrant Inspection Kit 37 Multi Scan Tool With Oscilloscope Diagnostic Scanner Ultra Scan P1 With Complete Software And 4 Adaptors’ Suitable For All Mpfi & Crdi Vehicles / Built-In Can Bus System / 512Mb Memory Card / Live Data / Activation Test Parameter Reset / Key Coding / Blackbox Flight Record / Ecu Simulation / Digital / Millimeters / 4 Channel Oscilloscope / Ignition Pattern Analyzer / Gas Analyser Interface Usb Direct Pc Interface Specification : -Internal Memory : Lmbyte Srammemory Card : 512Mbyte Nand Flash Memory Display : 32Ox24o Graphic Lcd Wiih Led Backlight Input Device : Membrane Keypad Quality System : Iso9001:2000Emc Compliance : Ce / C-Tick / Fcc / Gost Special Function : -Oscilloscope -Four Channels Display Up To 4 Scope Graphs At One Time -High Speed Digital Scope Samplins Rate 500Khz -19 Pre- Setup Sensor Selection Auto Setup, Standard Pattern Presentation -Host-Pro Real Time Pc Interface View Waveform By Pc Screen Through Usb Ignition Pattern Analyzer Primary & Secondary Ignition Pattern -Conventional And Dliidis Engine -Display Mode Individual Waveform-Single Pattern For Cyliner Parallel Waveform-Up To 6 Cylinders Peak Voltage Bar Graph Display ( Up To 8 Cylinders ) Battery Voltage, Dwel Angle, Spark Time Indication Host-Pro Realtime Pc Interface View Ignition Pattern By Pc Screen Through Usb Digital Multimeter -Dual Channel -Voltage Meter : Dc 30V -Frequency Meter : Lhz-I } Okhz -Duty Cycle : O-99.9Vo -Current Meter : 0T 128A ( Optional ) Emission Analyzer Interface Real Time Interface With Im2400 Ultra 4 / 5 Gas Analyzer That Enables Simultaneous Display, Record And Replay Of Scanner Data And Gas Readings -Reliability Andros 6241 Inspection Level Gas Bench -Business Solution A Solution For Countries With I / M Program And Regulations 38 Multimedia Dvd For Automotive Application / Subjects 39 Oxy – Acetylene Gas Welding Set Equipment With Hoses, Regulator And Other Accessories. 40 Plate Bending Machine ( Roller Type ) Capacity Upto 8 Mm Thickness 41 Portable Abrasive Cut-Off Machine 42 Portable Electric Drill Machine 6 Mm Capacity 43 Power Saw Machine – Hydraulic Feed System – 400 Mm. Blade Size. 44 Radiator Cut Section-Cross Flow This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information And The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 45 Radiator Cut Section-Down Flow This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information And The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 46 Radiator Pressure Cap 47 Ss And Sc Centre Lathe ( All Geared ) With Minimum Specification As: Centre Height 150 Mm And Centre Distance 1000 Mm Along With 3 & 4 Jaw Chucks, Auto Feed System, Safety Guard, Taper Turning Attachment, Motorized Coolant System, Lighting Arrangement & Standard Accessories. 48 Starter Motor Co-Axial Type This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information, And Working Of The Same, The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 49 Starter Motor Pre-Engagement Type This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information, And Working Of The Same, The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 50 Starter Motor Axial Type This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information, And Working Of The Same, The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 51 Tandem Master Cylinder With Booster This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information And The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 52 Temperature Gauge With Sensor 0-100 Deg C 53 Thermostat-0-100 C 54 Advance Timing Lighter For Checking And Setting Ignition Timing On Automotive, Agricultural And Marine Engines. Measures Ignition Spark Advance From 0-60Ş. For Use On 12V Systems. Reverse Polarity Protected. Accurate To 8, 000Rpm. 1M Long Removable Coiled Power Leads. Impact Resistant Metal Case And Rubber Nose Cone. On / Off Trigger Switch. Bright Linear Xenon Flash Tube For Daylight Use. Focused Lens Provides A Concentrated Light. Easy To Apply Inductive Impulse Pick-Up. Built-In Check Light. 55 Transformer Welding Set 150 Amps. – Continuous Welding Current, With All Accessories And Electrode Holder 56 Trolley Type Portable Air Compressor Single Cylinder With 45 Liters Capacity Air Tank, Along With Accessories & With Working Pressure 6.5 Kg / Sq Cm 57 Turbocharger Cut Sectional View This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information And The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 58 Water Pump For Dismantling And Assembling This Model Is Made Out Of Original Used Parts, Will Be Suitably Sectioned To Demonstrate The Internal Construction Details Showing The Minute Information, And Working Of The Same, The Model Will Be Suitably Painted And Mounted On A Navopan Wooden Base. 59 Welding Plant Oxy-Acetylene Complete ( High Pressure ) With Regulator Tenchnical Specification: A ) High Pressure Welding Torch With 6 Nos. Tips Complete As Per Isi Marked Tip Size 2, 3, 6, 13, 20 & 30 B ) Double Stage Oxygen Regulator Fitted With Two Pressure Gauges & Outlet Valve Complete Conforning To Is. Inlet, Pressure Gauges:0-280 Bar Outlet Pressure Gauge:0-10 Bar C ) Double Stage Acetylene Regulator Fitted With Two Pressure Gauges & Outled Valve Complete Conforning To Is Inlet Pressure Gauge:0-40 Bar Outlet Pressure Gauge:0-2.5 Bar D ) Hose Clip 8 Mm, Goggles For Welding And Cutting With One Pair Dark Glass Of 4 / 5 Din And One Pair Clear Glass , Cylinder Outfit Spanner ( Spaindle Key Single End Spark Lighter.Apron Made Of High Split Leather Size 24 X 36 ( With Out Gas Cylinder ) 60 Welding Transformer ( 150-300 Amps ) 61 Welding Transformer Or Invertors With All Accessories ( 300A , Ocv 60 ± 100 V, 60% Duty Cycle ) 62 Welding Transformer With All Accessories ( 400A , Ocv 60 ± 100 V, 60% Duty Cycle ) 63 Work Bench 250 X 120 X 60 Cm With 4 Vices 12Cm Jaw 64 Work Bench Approx. Size 340X120x75 Cm With 4 Bench Vices Of 150 Mm Jaw 65 Working Bench 2.5 M X 1.20 M X 0.75 M 66 Working Condition Of Diesel Engine – Crdi - 4 Stroke Engine Assembly With Fault Simulation Board The Device Is Designed Based On Latest Technology Diesel Engines With Common Rail Direct Fuel Injection System. The Trainer Helps To Simulate Engine Startup, Speedup, Slowdown And Other Actions So As To Illustrate The Structure And Working Principle Of Crdi Engines. Features 1. Real And Operating Crdi Diesel Engine, Illustrating The Structure And Working Process. 2. Coloured Circuit Diagram On The Training Module Printed On To 6Mm Organic Glass Base.. 3. Detection Terminals For Operator To Detect Various Sensors, Actuators, Electrical Signals For Engine Control Unit, Such As Resistive, Voltage, Current , Frequency And Wave Form Signals Are Provided On To The Printed Circuit Diagaram. 4. Automobile Meters Are Fitted On To The Training Module Along With The Printed Circuit Diagram, To Demonstrate Engine Speed, Temperature, Fuel Pressure, Charging Light Etc., 5. The Training Module Is Fitted With Diagnostic Socket ( Dlc ) For Universal Automobile Decoder ( Scan Tool ) To Read Fault Codes, Clear Fault Codes And Read Data Stream. 6. Fault Setting Switch Bank Will Be Provided To Induce Faults In The Training Module To Demonstrate The Fault And To Diagnose Faults. 7. Good Working Condition Engine Will Be Provided With Fuel Tank And Battery. Throttle Control Is Provided On The Module To Accelerate. 8. The Training Module Is Fabricated Using Steel Pipe Frame With Spray Painted For Good Looks And The Entire Setup Is Provided With Caster Wheels With Brakes For Easy Movement Of The Same. 67 Portable Drilling Machine ( Cap. 6 Mm ) 68 Gmaw Welding Machine 400A Capacity With Air Cooled Torch, Regulator, Gas Preheater, Gas Hose And Standard Accessories 69 Ac / Dc Gtaw Welding Machine With Water Cooled Torch 300 A, Argon Regulator, Gas Hose, Water Circulating System And Standard Accessories. 70 Air Plasma Cutting Equipment With All Accessories, Capacity To Cut 12 Mm Clear Cut 71 Portable Gas Cutting Machine Capable Of Cutting Straight & Circular With All Accessories 72 Pedestal Grinder Fitted With Coarse And Medium Grain Size Grinding Wheels Dia. 300 Mm 73 Bench Grinder Fitted With Fine Grain Size Silicon Carbide Green Grinding Wheel Dia. 150 Mm 74 Welding Simulators For Smaw / Gtaw / Gmaw 75 Spot Welding Machine
