Supply Of Equipments Auto Clave (Vertical)The Vertical Autoclave Should Have Chamber Size Ø35 X 55 Cm. The Chamber Of Vertical Autoclave Should Be Manufactured As Per Asme Standards., 230 V Ac, 50 Hz, Single Phase. The Units Internal Chamber, Cover Lid And All Wetted Parts Should Be Fabricated From Ss Of 304 Grade. The Vertical Autoclave’S All Joints Should Be Smooth Finished For Crevice Free Internals. The Outer Body Should Be Made Up Of Ms Sheet With Heat Cured Epoxy Coating On Both Sides. The Lid Should Be Equipped With Single Lever Lock Mechanism And Lever Handle Moulded From Industrial Plastic. The Lid Should Be Provided With Auto Purge Cum Vacuum Breaker Valve And A Manually Operable Valve For Exhaust. The Unit Should Have A Solenoid Valve For Auto Purging Of Air & Normal Exhaust. The Vertical Autoclave Should Have Stainless Steel Pressure Gauge With Dual Range Dial Display In Kpa And Psi Along With A Co-Related Temperature Scale For Steam In Deg C. The Operations Of The Unit Should Be Controlled By A Microprocessor Based Controller. The User Should Be Able To Set The Temperature Up To 122 Deg C In Steps Of 0.1 Deg C Each. The User Should Be Able To Set The Sterilization Hold Time In Steps Of 1 Minutes Each. The Timer Range Should Be Up To 95 Mins. In Case Of Abrupt Power Failure / Switching Off, The Last Cycle Which Was Set Should Remain In The Memory. The Display For The Parameters Should Be Two Line Alpha-Numeric Digital Display. The Unit Should Be Equipped With Low Water Detection Unit And Should Give Audio- Visual Alarm In Case Of Low Water In The Chamber And Cut Off The Supply To The Heater. The Unit Should Have Safety Valve To Protect The Equipment In Case Of Over Pressurization. The Lid Should Be Equipped With Pressure Interlock Device. Also The Heater Should Not Start If The Lid Is Open. The Unit Should Be Provided With Safety Cut-Out For High Temperature. The Unit Should Give Indication By Audio-Visual Alarm On Completion Of Set Autoclave Cycle. The Electrical Safety Should Be Ensured By Inbuilt Mcb. The Unit Should Be Mounted On Pu Coated Castors Out Of Which At Least 2 Should Have Locking Mechanism. Supplied With Suitable Voltage Stabilizer The Vertical Autoclave Should Be Ce Certified. Manufacturer With Iso 13485 Certified Will Be Preferred. Calibration Reports With Nabl Traceability To Be Given With Autoclave. Capacity :50 Ltrs Equipment Shall Be Supplied With -Three Years Warranty Radiant WarmerServo Control Advanced Microcontroller Based Self Diagnostic With Proportional Temperature Control. Resuscitation (Optional) With Bottom Phototherapy. Switchable Air / Servo Mode. Continuous Baby’S Body Temperature Monitoring And Control With Precise Accuracy. Safety Alarms For All Faulty Conditions. Unit Mounted On Castors For Easy Mobility. Digital Control Solid State Proportional Control With Higher Accuracy. Rugged Design For Stability And Durability. Silica Heater Used For Uniform Temperature Distribution. Safety Alarms Provided For Probe Failure And High Temperature Condition. Trendelenberg Facility Provided For Tilti Power Supply : 230/240 V Ac 50Hz Single Phase Power Consumption : 650 Watts Approx. Operating Modes : Air Mode Accuracy : In Stabilized Condition + / - 0.2 º C. Display Resolution : 0.1 º C Temperature Control : 28.0 º C. To 37.0 º C In Air Mode High Temperature Cut Off : Around 38.5 º C. Alarm Indication : Audio And Visual Warning With Automatic Heater Cut-Off. Heater Control : Tdm Control Zero Emi Oxygen Concentration Achieved : Head Box (Oxygen Hood) To Be Used. Operating Room Temperature : 21.0 º C To 30.0º C. Storage Temperature : 10 º C To 50 º C . Baby Tray Tilt : 15 º At Either End. Stabilization Time : 15 Minutes Fuse Type : 230 V 5A Rating Small Glass Fuse. Dimension : H Eight : 1900 Mm Width : 500 Mm Depth : 675 Mm Weight : 30 Kgsng Of Baby Tray.Suction ApparatusSuction Machine With Pump: - Power Supply: 230-240V/50Hz - Vacuum Capacity: 18 Litres/Mim - Maximum Depression: -75Kpa (-563Mmhg) Vacuum Is Created By A Plastic Piston And Cylinder System, With Four Vacuum-Creating Modules (Quatroflex™ Technology). The Membrane Vacuum Regulator Permits Accurate Vacuum Settings. Double Overflow-Protection System (Bottle And Pump). Working Temperature Range: +5 To +40°C.Adult Weighing ScaleEquipped With A High Precision Strain Gauge Sensor. 8Mm Tempered Safety Glass Platform. Size Of The Lcd Digits: 25Mm (1) Edge-Tap Switches On. Auto Zero Resetting/Auto Off. Power: 2X Cr2032 Li-Ion Battery Capacity: 150 Kg (330Ib) Division: D=100G(0.21Ib)Baby Weighing ScaleElectronic Scale For Weighing Babies. Measuring Range 0 To Approx 10 Kg. Minimum Graduation: 5 G. With Tare Function. On Switch And Auto-Off. Auto-Calibration With Each Switch-On. Large Led Display Readable In Low Light Working Situations, Display Cover Durable Plastic. Display In Kg And Lbs, Easy Switch Between Kg And Lbs. Reading Time Max 5 Seconds. Zero Weighing Adjustment. Smooth Surface/Finishing Allows For Easy Cleaning/Disinfection. All Vital Parts Made Of Rust Proof Materials. Horizontal Leveling With Height Adjustable Feet. Splash Proof And Shock Resistant Light-Weight Body. Power Requirements: 220 V / 50 Hz. Power Consumption: 150 W.Height Measuring ScaleGoose Neck LampPhototherapy UnitNst MachineFoetal Doppler§ Should Be 12.1 High Resolution Colour Tft Display With Tiltable Screen § Should Be Standard Configuration: Fhr, Toco, & Foetal Movement § Should Be Compact, Portable And Lightweight § Should Be Large Letter Display Interface § Should Be Special High Sensitive Waterproof Probe § Should Have Volume Control For Fhr § Should Be12 Hour Data Storage With Play Back & Print Facility § Thermal Paper Should Be Available Locally § Should Be Low Ultrasound Power, Safe On Foetus § Should Be Automatic Detectionfoetal Movement With Event Marker § Should Provide Belt For Both Ultrasound And Toco Transducer § Should Be In-Built Rechargeable Li-Ion Battery § Should Havecentral Monitoring System Software (Optional) § Warranty Two Years § Should Quote For The Equipment After Warranty Periodamc/Cmc For Next One Year.Bp ApparatusFirst Grade Quality - Virgin Material Used Purity Of Mercury 99.99% Due To Assured Triple Distillation Process 0 To 300 Mm Of Hg Scale With Elegant Finish, Fine Numbering And Durable Background Contrast Paint For Clear Visibility Fused Type, Permanent Graduation Marking On The Glass Tube Special Control Valve For Perfect Pressure Drop Best Quality Cuff For Getting Excellent Grip Proven Rubber Material Like Bag And Bulb To Give More Durability Surface Plating Adapted To All Exposed Metal Parts To Prevent Corrosion Classic Hi-Stove Painting To The Body Of The Instrument To Withstand In Any Climate Optimum Damping Effect Provided For Easy And Fast MeasurementStethoscopeDeluxe Stainless Steel Head, For Adults. Stainless Steel Binaural With Thick Tubing Assembly Soft Ear Tips Assure Maximum Comfort And Excellent Acoustical Seal Stainless Steel Binaural With Thick Tubing Assembly The Conducting Tube Features An Embedded Elastic Sheet With High Durability. Resistance To High And Low Temperature, Minimal Susceptibility To Deforming And Ageing, And High Fidelity. The Earphone Can Perfectly Fit The Auricle With No Sound Leakage And Feels Good In Long Time Use.NebuliserPneumatic Nebulizer / With Compressor 0.2 Ml/Min | FoggyjetRefrigerator2 Doors Refrigerators With 70 Liters Freezer Capacity, Has Frost Free Defrosted System And Clea Back. It Shall Be Have 12 Shelves And Boxes Which Are Adjustable. It Shall Have Other Facility Like Deodorizing Ability, Door Lock And Moisture And Humidity Control. It Has Cool Ever Zone And Cool Pack Which Helps In Maintain A Low Temperature In The Freezer Section And Refrigerator During The Power Failure. It Shall Have Unique Freshness Lamp, Fire Retardant Wires And Rust Resistant Cabinet. Capacity 360Ltrs. Supplied With Suitable Std Stabilizer And Stand . Equipment Shall Be Supplied With -Three Years Warranty Hyduralic TableSteel Top & Steel Base And Mounted On Sturdy Castor Trendlenburg Each 30 Deg, Lateral Tilt Each 30Deg, Back Break 90 Deg Up. Hyduralic Pump Elevation With Brass Lock For Accessories Rotation In 360 Deg With Locking System Detachable Head & Leg Table Top:48.5 X 180 Cm Elevation: 70Cm To 100Cm Weight 250KgOt Light Central MobileLight Intensity: 1,00,000 Lux Color Temperature : 5000 Kelvin C.R.I. 99% Temp Rise At The Head Area : 1 Deg Maximum Temp Rise At The Operating Area : < 5 Deg 10 Intensity Color Setting In Steps* (Optional) Improved Contrast, Giving Less Fatigue With Greater Ease Of Operation Durable Long Led Life Expectancy Of 50,000 Working Hours No Distortion Of Colors Easy To Position 360 DegOxygen Flow MeterSemi Automatic AnalyserLight Source • Quartz-Halogen Lamp 12V-20W. Wavelength Range • A Utomatic By 12 Positions Filterwheel; • 6 Standard Interference Filters: 340, 405, 505, 546, 578 And 620 Nm; • 6 Positions For Optional Filters. Photo Metric Range • -0.1 To 2.3 Absorbance. Detector • Photo Diode (320-1000 Nm). Blanking • A Utomatic Zero Setting. Operator Interface • Membrane Keyboard, For Direct Function And Alpha-Numeric Entry; • O Ptional External Keyboard; • High Contrast Graphical Lcd Display; • R Eal Time Clock, 24 Hours System. Languages • E Nglish; Measurement Pro Cedures • Kinetic, With Linearity Check: • Kinetic, With Linearity Check And Sample Slope Blank; • T Wo Point Kinetic, With Or Without Reagent Blank; • E Nd Point, With Or Without Reagent Blank; • B Ichromatic End Point, With Or Without Reagent Blank; • End Point, With Sample Blank And With Or Without Reagent Blank. Mult Iple Test Ing • U P To Nine Replicates; • Means, Sd And Cv. Measuring Time • Programmable, 2 To 998 Seconds For Kinetic And Two Point Type Of Tests; • For End Point Fixed At 2 Seconds. Delay Time • Programmable, 0 To 999 Seconds. Method Parameter Sett Ings A.O. • Method Name; • Measurement Mode; • Wavelenght 1 And 2; • A Spiration Volume; • Measurement Delay; • Measurement Time; • Factor; • C Oncentration Standards; • R Eagent Blank Y/N; • S Ample Blank Y/N; • U Nits For Results; • L Evels For Flagging; • C Urve Fit Y/N; • L Inearity Check. Calibration • Factor, One-Point, Two-Point And Multi-Point; • A Utomatic On 1 Standard (Linear Mode); • A Utomatic On Up To 10 Standards (Non Linear Mode). Quality Control • T Wo Controls Per Test; • Qc Survey Of Last 30 Control Measurements; • L Evey Jenning Plot; • High/Low Flags. Flo Wcell • Metal, With Quartz Windows, Measuring Volume 30 Μl. Temperature Control • B Y Means Of Peltier Elements; • Fixed Temperature At 37°C. Aspirator Syste M • I Nternal Pump Of Bellows Type, Driven By Stepper Motor: • Back Panel Connection For Waste; • A Spiration Volume Programmable. Printer • I Nternal Matrix Printer; • N Ormal Paper; • E Xternal Printer Port Available. Signal Interface • C Entronics Type Parallel Port; • Rs 232 Type Serial Port; • Ps 2 Type Port For External Keyboard. Quality • Ul ;• Ce ;• Cb Certificate. Power Requirements • 100-240 Vac Nominal, 50/60 Hz; • B Attery Back-Up To Retain Data. Dimensions • 40 X 17 X 36,5 Cm (W X H X D). Weight • 8,5 Kg.Binocular MicroscopeBinocular Head With Ocular Adjustable In Both Occular Must. One Piece Sturdy Stand. Semi Plan Achromat Objective , Objectives 10X,20X,40X,100X Oil Immersion Spring Loaded Led Illumination With Battery Back Up Eye Piece Wf 10X ( 18Mm Field Of View) Centrifuge99 Programs With ( 5 Direct Acess Key) Digital Countdown Timer 0-99Hr,59 Min With Continuous Run. Automatic Rotor Identification ,Automatic Door Opening ,Motor Over Load Protection,Emergency Lid Lock Release,Imbalance Detection With Centrifugation Cut Off Without Any Screws To Fix The Rotor. Max Speed: 15200Rpm , With G Force Of 25,830 The Range Of Control Of Refrigeration Should Be -10 Deg C To 40Deg C. Accelaration And Decelaration Profiles Shall Have 0-9 Levels, Should Have Fast Spin And Quick Cooling Features , Calibration Window On Lid For Speed Display: Led/Lcd ,Control Communication : Digital, Self -Diagnostics Of Erros Brushless Motor With Frequency Drive Cfc Free Refrigeration System The Centrifuge Should Have Advanced Imbalance Technology That Adapts For Specific Rotors. Rotors : Supplied Along With Centrifuge Swing Bucket Rotor 400Ml Max Rpm 4000.-1No To Spin At Least 76 Of 5/7 Ml Tubes Aerosol Tight Buket With Sealing Caps/ Aerosol Tight Caps Bucket-2Pcs, Fixed Angle Rotor To Spin 48X2 Of 2Ml With Minimum Rpm Of 15200 Supplied With Suitable Voltage Stablizer Equipment Shall Be Supplied With -Three Years Warranty Split Ac Capacity: 2 Ton(S)Split, Active Carbon Deodoriser, Dehumidification, Remote Control Features: Active Carbon Filter, Anti Rust Cabinet, Auto Restart, Auto Swing, Independent Dehumidification, Leakage Detector, Led Display., Self Diagnosis, Sleep Mode, Turbo Mode Dimension: 1080X225x330, Weight:20 KgSolar Water HeaterName & Specification Of Furniture.Labour Cot SteelOverall Size: L-72, W-30, H-30 Top Sheet: Stainless Steel 16 Gauge 304 Grade, Double Press Bent, Mirror Polished And With U Cut Design: Sturdy Frame Work Made Up Of 16 Gauge S.S. 202 Grade 1 ¼ Sq. Pipes (Tubes) With Cross Bars-Both At Top And Bottom Sides Of 1 Sq. S.S. Tube 202 Grade. 2 Nos. Lithotomy Rods Adjustable S.S.304 Grade ½ Sq. Located On Both Sides With Ankle Stripes (Rexine). Lithotomy Rod Holders- S.S. Mirror Finished. All The Corners Are Grounded And Blunted. Nylon Feet To Be Provided. The Above Product Should Confirm To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance. All Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Hospital CotAdult Steel Sheet Cot. Size-78Lx36Wx24H, 1 ¼ Dia 14 Swg Tubular Head And Leg Bows Erw Tube. The Head Bow And Leg Bows Are 42 And 36 Height Respectively. Head And Leg Bows Should Have 14 Gauge, 1 Dia Erw Cross Bar And ½ Dia 16 Gauge Erw Three Vertical Support Bars. Top Sheet 16 Swg Crca Sheet, Double Press Bent Uniformly On All The Four Sides, 2 Vertically And ¾ Further Inside. A 6 Broad X 2 Deep Full Length 16 Gauge Square Cross Section Rib Should Be Reinforced To The Top Sheet 2 Nos. M.S. Gages Using 10 Swg, 4 Broad X 6 Length To Be Welded On Each Side Of The Bows For Fixing The Cot Top Steel Sheet To The Frame By Using 8 Nos. Zinc Plated ½ Nuts & Bolts. Facility For Fixing Mosquito Net Poles To Be Provided On The Side Of The Bows. 4 Nos. Of Shoes Made Up Of White Nylon Are To Be Provided. Epoxy Powder Coated With Seimen’S Gray Colour With 50 Microns Minimum Coating. The Above Product Should Conform To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance The Above Items Must Conform To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.MattressSize: 76” X 36” X 4”. Latex Coir Oriented Mattress With 75 Mm Coir Block. Top Side Pasted With High Density Polyurethane Foam Of25 Mm Thick Covered With Protective Inner Cover Of 20’S X 20’S Grey Cloth. Further S.T. Quality Green Drill Back Rexine Cover. Density Of The Latexed Coir Block Should Not Be Less Than 80 Grams /Dm^3. Four Sides Of The Block Should Be Re-Inforced By Cotton Blanket Cloth.Examination TableOverall Size:L-72, W-27, H-33 Top Sheet:Crca 16 Swg M.S. Sheet, Double Press Bent In Tow Sections Head Rest:L- 17, W-27 Adjustable On Ratchet Design :Main Main Frame Made Of Erw 16 Gauge 1 Sq. Pipe With Cross Bars Of 1 Sq. Pipe Both On Top And Bottom Sides. The Top Sheet Should Be Reinforced With A Full Length Rib Of 16 Gauge Thick And 6 Breadth. Nylon Bush (White) Paint:Epoxy Powder Coated With Seimen’S Grey Colour Of Minimum Of 50 Microns The Above Product Should Conform To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance The Above Items Must Conform To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent. Instrument TrolleyOverall Approx Size: 680 Mm Lx 450 Mm W X 900 Mm H. Design: Sturdy Frame Work Made Up Of 16 Gauge S.S 304 1” Tubular Frame Mounted On Four Castors Of 100 Mm Dia. Two Stainless Steel 16 Gauge 304 Grade, Double Press Bent, Mirror Polished Shelves With 1 Protruding Railings On Three Sides. The Above Product Should Confirm To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance All Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Dressing TrolleyOverall Approx Size: 680 Mm Lx 450 Mm W X 900 Mm H. Design: Sturdy Frame Work Made Up Of 16 Gauge S.S 304 1” Tubular Frame Mounted On Four Castors Of 100 Mm Dia. Two Stainless Steel 16 Gauge 304 Grade, Double Press Bent, Mirror Polished Shelves With 1 Protruding Railings On Three Sides. Provision To Mount Stainless Steel Basin Of 12” Dia And 12” Dressing Bins On One Side Of The Trolley. The Above Product Should Confirm To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance All Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Drip StandAdjustable From 60 To 90 Central Stand-16 Gauge Erw 1 Sq. Pipe 4 Winged Base Each Wing Having A Length Of 9, Base Of 2 X 1 Cross Section. 10 Gauge Rectangular Tube On 2 Swiveling Nylon Castor Wheels. A Telescopic ½ Dia S.S.304 Grade Rod With Double Hooks. Locking Hook (Grip) Mad Of Ss Stud Fitted With Bakelite Knob For Holding Saline Rod In The Position Epoxy Powder Coated In White Colour With Minimum 50 Microns The Above Product Should Confirm To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance. All Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Foot Elevation Double StepOverall Size: 18”X9”X20” Top Sheet: S.S.304 Grade Sheet, 18 Gauge S.S. Design: Top Fitted With Aluminum Tread Flats. Height 9 And 20 1 Sq.16 Swg S.S. Pipes To Be Used. 4 Nos. Nylon Feet The Above Product Should Confirm To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance. All Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Bed Side LockersFramework Of The Medicine Trolley Has Two S.S. Shelves & Two Smooth Drawers. These Medicine Trolleys Cover The S.S. Rails To Cover Three Sides Of Top Shelf & Four Of Bottom. Medicine Trolley 60X45x80cm. S.S. Tubular Frame Mounted On Four 10 Cm Swivel Castor, Two With Breakings. Overall Size Of The Medicine Trolley:-101L*50W*90H.Revolving Stool 4 LegOverall Size: 12 Dia Round Top S.S. Sheet, Revolving With Height Adjustable From 20 Min. To 28 Max. From Floor By Machined Screw Mechanism.Design: Frame Made Up Of 14 Gauge Erw 1 Dia Pipe Tripod. Leg To Leg 16 Apart. A Round Top Crca 10 Gauge Should Have A Ring Of Same Dia. M.S. Metal 1 X ¼Flat, So That The 22 Swg S.S. Top Sheet Would Be Beaded Of Inside. Top Mirror Polished. The Central Guiding Tube Of 10 Gauge Erw And The Screw Rod Of Dia 1½ And The Nut (En8 Alloyed Steel) Are Firmly Welded. Nylon Feet Are To Be Provided. Paint: Epoxy Powder Coated In Siemens Gray Colour With Minimum 50 Microns.The Above Product Should Conform To Applicable Isi Standards In Respect Of Materials Welding Process, Tests And Performance.The Above Items Must Conform To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.BasinBasin StandPillowsSize : 30” X 16” X 5” Rubberized Coir Pillow With Inner Cover White Sheeting Cloth Cover Land Outer Cover S.T. Quality Green Drill Back Rexine Cover. The Above Products Should Confirm To Applicable Isi Standards In Respect Of Materials, Tests And Performance. All Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Chair S TypeS-Type Chair Made Of 1” Heavy Ms Tubular Frame & Duly Powder Coated With Wooden Hand Rest. Seating & Backrest Made Of Nylon Rope Netted In Wooden Frames. Suitable Heavy Pvc Bushes In The Bottom For The Chair. Epoxy Powder Coated With Seimen’S Gray Colour With 50 Microns Minimum Coating. The Above Product Should Conform To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance The Above Items Must Conform To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Chair Visitor - 3SeaterA Unit Of Three Seater M.S. Perforated Bucket Type Visitor Chairs With Arm To Be Supplied As Follows: Frame Made Out Of M.S. Square 35X35 Mm 16 Gauges. Two Nos. Of Vertical Supports Of 35X35 Mm 16 Gauge Square On Each Side To Be Provided Interconnected By A Cross Member Of Same Dimension. Two Nos. Of Horizontal Supports Of M.S. 35X35 Mm 16 Gauge 40 Cm Length To Be Provided At The Bottom. Three Chairs To Be Mounted On The Frame With Welding. Provision Of Suitable Moulded Studs To Be Incorporated At The Bottom Of Seats For Rigid Mounting. Dimensions Of Seat Is As Follows: Seat Height: 37-40 Cm Seat Length: 37-40 Cm Seat Width: 58-60 Cm The Above Product Should Conform To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance. The Above Items Must Conform To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent. Epoxy Powder Coated With Black Colour With 50 Microns Minimum Coating.Doctor Table With DrawsMade Out Of Pre-Laminated Particleboard With Special Top Surface, 3 Nos. Drawers On Either Side Slides Smoothly On Roller Bearings. Flush Drawers Have Single Key Locking Facility For 3 Drawers. Table Legs Are Made Out Of Erw Steel Tube, Rectangular Or Size 4 X 3 Cm Of 14 Gauges. And Top Frame Of Size 3 Cm. Frames Welded By Mig Welding Process. Frames Are Powder Coated With Minimum Thickness Of 50 Microns. Tabletop Is 25Mm Thick Phenol Bonded Particleboard Mounted On 1Mm Thick Laminate. Size Of The Top Is 72” X 36”. Backing Sheet 0.5 Mm Thick To Glued Below The Tabletop Using Good Adhesive. All Exposed Edges Are Bonded With Pvc Tapes. Hardware Of Good Quality, Height To The Table Is 0.76Meter. The Above Product Should Conform To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance. The Above Items Must Conform To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Steel Almirah-BigSteel Almirah 6.6 Ft With 4 Shelves Plain Overall 18 Gauze Size 78”X36”X19” Wheel ChairFoldable Wheel Chair For Patient With 2 Solid Rubber Tyred Bicycle Wheel With C.P. Hand Hoops Castor Wheels In Front Foldable Metal Foot Rest. Stretcher On TrolleyDimensions: 213 (L) X 56 (W) X 81 (H) Cm Frame Work Of Crc Tubes Mounted On 15 Cm Castors Removable Stretcher Top With Chrome Plated Handle Pre-Treated And Epoxy Powder Coated Finish Without MattressSteel Almirah( Small )Executive Chair Half BackApproximate Dimensions Seat Depth 480 - 500 Mm Seat Width 480 - 500 Mm Back Height With Foam Seat 380 - 400 Mm 5 Star Gravity Aluminum Die Cast, Base Made From High Quality Material Confirming To I.S. 6051 / 1970. Base Should Have 5 Nos. Specially Designed Twin Wheel Castors (Castors To Be Abrasive Resistant And Resistant Free Movements On Carpets). Manually Seat Height Adjustment And Lockable At Any Suitable Height.The Chair Should Have Tilting Mechanism. The Structure Of The Mechanism Is Manufactured Out Of Crc Steel Sheet. The Seating Structure Is Made Of Erw Steel Tubular Structure Upholstery To Be Made Out Of Polyurethane Foam Of 55 Density Thickness 37 Mm Backed By 1” Kurl On.Arms Of The Chair Are To Be Made Of Moulded Self Skin Pu Arm With Steel Insert For Long Life.The Above Product Should Conform To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance.The Above Items Must Conform To The Relevant Quality And Safety Standards Such As Iec 601 - 1 And Bs 5724 And The Indian Equivalent.All Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.The Above Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601 - 1 And Bs 5724 And The Indian Equivalent.Bed Side Screen 3 FoldsOverall Size: 96 Wx60H Top Sheet: ¾ Diameter Tubular Frame 16 Swg In 3 Sections. Middle Span 48. Provision For Hooks To Fix Springs. Mounted On 6 Nos. 2 Nylon Castors Wheels Design: Epoxy Powder Coated In White Colour With Minimum 50 Microns The Above Product Should Confirm To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance. All Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601-1 And Bs 5724 And The Indian Equivalent.Steel Slotted Angle RacksSteel Rack Made Of Slotted Angles Of Size 2”X2”X3mm Thick, 5 Compartments Of Six 6’ X 1 ¼’X 3’ Length. Paint: Epoxy Powder Coated In Siemens Gray Colour With Minimum 50 Microns. The Above Product Should Confirm To Applicable Isi Standards In Respect Of Materials, Welding Process, Tests And Performance. The Above Items Must Confirm To The Relevant Quality And Safety Standards Such As Iec 601 - 1 And Bs 5724 And The Indian Equivalent.Attainder’S Stool (4 Legged)Stainless SteelSteel Tray With Lid SmallSteel Tray With Lid BigArtery Forceps 6” CurvedArtery Forceps 6” StraightNeedle Holder LongNeedle Holder ShortEpisiotomy Scissor 6Dissecting Toothed ForcepsSpeculum SimsVulsellumCuratorOvum ForcepsVaginal ReactorSuture Removal ScissorsTorch BigFor Quick And Effective Evaluation Of Pupillary Reflex. Spot Illumination With Out Peripheral Ring Of Light. Easy To Handle And Easy To Power On And Off.Ss Bin BigDressing Drums Sizes Are Measured From Hinges To Hinges. Products Mentioned As Super Deluxe Are Made Of Heavier Gauge. Products In 304 Grade S.S. Ss Bin SmallDressing Drums Sizes Are Measured From Hinges To Hinges. Products Mentioned As Super Deluxe Are Made Of Heavier Gauge. Products In 304 Grade S.S. Ss Bin MediumDressing Drums Sizes Are Measured From Hinges To Hinges. Products Mentioned As Super Deluxe Are Made Of Heavier Gauge. Products In 304 Grade S.S. Alice Forceps 6”Bp Handle No3Bp Handle No4Curved Mosquito ForcepsStraight Mosquito ForcepsMayos Cutting Scissor StraightMayos Cutting Scissor CurvedCervical Punch Biopsy ForcepSponge Holding ForcepShirodkars HookDilatorsMr SyringeName Of LinenBedsheet WhiteSpecification: Bed Spread: Size 90 X 60 Pure Cotton 20S X 20S Qualities.Bedsheet BlueSpecification: Bed Spread: Size 90 X 60 Pure Cotton 20S X 20S Qualities.Pillow Cover WhiteSpecification: Pillow Cover: Suitable For Pillow Size: 30” X 16” X 5” Pure Cotton Pillow Cover Of 20S X 20S In Blue/Green Coloured.Pillow Cover BlueSpecification: Pillow Cover: Suitable For Pillow Size: 30” X 16” X 5” Pure Cotton Pillow Cover Of 20S X 20S In Blue/Green Coloured.Baby SheetAbdominal SheetSize : 45” X 85”, ¾ 8 Inch Hole At Abdominal Region.Ot TowelsSize : 35” X 35” And Hole Size 7” Made Of Pure Cotton Auto CleavableDoctors GownPuncture Resistant Fine Finish Water And Dust Repellant Light Weight, Ideal Fitting And Optimal Antibacterial PropertyPatients GownPuncture Resistant Fine Finish Water And Dust Repellant Light Weight, Ideal Fitting And Optimal Antibacterial PropertyDraw SheetSize : 38”W X 58”Perineal SheetSize : 35”W X 75”L, ¾ Hole 8 InchesHand TowelSize : 35” X 35” And Hole Size 7” Made Of Pure Cotton Auto CleavableBlanket BlueSpecification: Blanket: Size 90 X 60 Blanket Red / Blue Colored. Weight Should In Between 1800 Grams - 2000 Grams.Curtain ClothSize : 4 X 5 Feet , Type : Cotton Cloth
